Optimized from Version1.03

ubitx_20/cat_libs.ino

@@ -1,4 +1,5 @@
 /*************************************************************************
+  KD8CEC's CAT Library for uBITX and HAM
   This source code is written for uBITX, but it can also be used on other radios.
   
   The CAT protocol is used by many radios to provide remote control to comptuers through
@@ -108,7 +109,8 @@ void CatSetFreq(byte fromType)
 //#define BCD_LEN 9
 //PROTOCOL : 0x03
 //Computer <-(frequency)-> TRCV CAT_BUFF
-void CatGetFreqMode(unsigned long freq, byte fromType)
+//void CatGetFreqMode(unsigned long freq, byte fromType)
+void CatGetFreqMode(unsigned long freq) //for remove warning messages
 {
   int i;
   byte tmpValue;
@@ -129,23 +131,40 @@ void CatGetFreqMode(unsigned long freq, byte fromType)
   }
 
   //Mode Check
-  if (isUSB)
-    CAT_BUFF[4] = CAT_MODE_USB;
+  if (cwMode == 0)
+  {
+    if (isUSB)
+      CAT_BUFF[4] = CAT_MODE_USB;
+    else
+      CAT_BUFF[4] = CAT_MODE_LSB;
+  }
+  else if (cwMode == 1)
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
   else
-    CAT_BUFF[4] = CAT_MODE_LSB;
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
 
   SendCatData(5);
 }
 
-void CatSetSplit(boolean isSplit, byte fromType)
+//void CatSetSplit(boolean isSplit, byte fromType)
+void CatSetSplit(boolean isSplit) //for remove warning messages
 {
+  if (isSplit)
+    splitOn = 1;
+  else
+    splitOn = 0;
     
   Serial.write(ACK);
 }
 
 void CatSetPTT(boolean isPTTOn, byte fromType)
 {
-  if (fromType == 2 || fromType == 3) {
+  //
+  if ((!inTx) && (fromType == 2 || fromType == 3)) {
     Serial.write(ACK);  
     return;  
   }
@@ -181,7 +200,7 @@ void CatSetPTT(boolean isPTTOn, byte fromType)
 void CatVFOToggle(boolean isSendACK, byte fromType)
 {
   if (fromType != 2 && fromType != 3) {
-    menuVfoToggle(1, 0);
+    menuVfoToggle(1);
   }  
 
   if (isSendACK)
@@ -197,12 +216,18 @@ void CatSetMode(byte tmpMode, byte fromType)
   
   if (!inTx)
   {
-    if (tmpMode == CAT_MODE_USB)
+    if (tmpMode == CAT_MODE_CW)
     {
+      cwMode = 1;
+    }
+    else if (tmpMode == CAT_MODE_USB)
+    {
+      cwMode = 0;
       isUSB = true;
     }
     else
     {
+      cwMode = 0;
       isUSB = false;
     }
 
@@ -214,7 +239,8 @@ void CatSetMode(byte tmpMode, byte fromType)
 }
 
 //Read EEProm by uBITX Manager Software
-void ReadEEPRom(byte fromType)
+//void ReadEEPRom(byte fromType)
+void ReadEEPRom() //for remove warnings.
 {
   //5BYTES
   //CAT_BUFF[0] [1] [2] [3] [4] //4 COMMAND
@@ -237,7 +263,8 @@ void ReadEEPRom(byte fromType)
 }
 
 //Write just proecess 1byes
-void WriteEEPRom(byte fromType)
+//void WriteEEPRom(byte fromType)
+void WriteEEPRom(void)  //for remove warning
 {
   //5BYTES
   uint16_t eepromStartIndex = CAT_BUFF[0] + CAT_BUFF[1] * 256;
@@ -257,7 +284,8 @@ void WriteEEPRom(byte fromType)
   }
 }
 
-void ReadEEPRom_FT817(byte fromType)
+//void ReadEEPRom_FT817(byte fromType)
+void ReadEEPRom_FT817(void) //for remove warnings
 {
   byte temp0 = CAT_BUFF[0];
   byte temp1 = CAT_BUFF[1];
@@ -357,10 +385,21 @@ void ReadEEPRom_FT817(byte fromType)
       CAT_BUFF[1] = 0xB2;
       break;      case 0x69 : //FM Mic (#29)  Contains 0-100 (decimal) as displayed
     case 0x78 :
-      if (isUSB)
-        CAT_BUFF[0] = CAT_MODE_USB;
-      else
-        CAT_BUFF[0] = CAT_MODE_LSB;
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          CAT_BUFF[0] = CAT_MODE_USB;
+        else
+          CAT_BUFF[0] = CAT_MODE_LSB;
+      }
+      else if (cwMode == 1)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
+      else if (cwMode == 2)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
         
       if (CAT_BUFF[0] != 0) CAT_BUFF[0] = 1 << 5;
       break;
@@ -383,7 +422,7 @@ void ReadEEPRom_FT817(byte fromType)
       //7A  6 ? ?
       //7A  7 SPL On/Off  0 = Off, 1 = On
 
-      CAT_BUFF[0] = (isSplitOn ? 0xFF : 0x7F);
+      CAT_BUFF[0] = (splitOn ? 0xFF : 0x7F);
       break;
     case 0xB3 : //
       CAT_BUFF[0] = 0x00;
@@ -471,7 +510,7 @@ void WriteEEPRom_FT817(byte fromType)
         printLineF2(F("Sidetone set! CAT"));
         EEPROM.put(CW_SIDETONE, sideTone);
         delay(300);                       //If timeout errors occur in the calling software, remove them
-        printLine2("");                   //Ham radio deluxe is the only one that supports this feature yet. and ham radio deluxe has wait time as greater than 500ms
+        clearLine2();
       }
       break;
 
@@ -483,7 +522,8 @@ void WriteEEPRom_FT817(byte fromType)
         printLineF2(F("Sidetone set! CAT"));
         EEPROM.put(CW_SIDETONE, sideTone);
         delay(300);                   //If timeout errors occur in the calling software, remove them
-        printLine2("");               //Ham radio deluxe is the only one that supports this feature yet. and ham radio deluxe has wait time as greater than 500ms
+        clearLine2();
+        line2DisplayStatus = 0;
       }
       break;
 
@@ -503,7 +543,7 @@ void WriteEEPRom_FT817(byte fromType)
       printLineF2(F("CW Speed set!"));
       EEPROM.put(CW_DELAY, cwDelayTime);
       delay(300);
-      printLine2("");
+      clearLine2();
       break;
     case 0x62 : //
       //5-0  CW Speed (4-60 WPM) (#21) From 0 to 38 (HEX) with 0 = 4 WPM and 38 = 60 WPM (1 WPM steps)
@@ -512,7 +552,7 @@ void WriteEEPRom_FT817(byte fromType)
       printLineF2(F("CW Speed set!"));
       EEPROM.put(CW_SPEED, cwSpeed);
       delay(300);
-      printLine2("");
+      clearLine2();
 
       break;
       /*
@@ -571,7 +611,8 @@ void WriteEEPRom_FT817(byte fromType)
   Serial.write(ACK);
 }
 
-void CatRxStatus(byte fromType) 
+//void CatRxStatus(byte fromType) 
+void CatRxStatus(void)  //for remove warning
 {
   byte sMeterValue = 1;
 
@@ -591,7 +632,8 @@ void CatRxStatus(byte fromType)
 }
 
 
-void CatTxStatus(byte fromType)
+//void CatTxStatus(byte fromType)
+void CatTxStatus(void)  //for remove warning
 {
   boolean isHighSWR = false;
   boolean isSplitOn = false;
@@ -692,11 +734,11 @@ void Check_Cat(byte fromType)
       
     case 0x02 : //Split On
     case 0x82:  //Split Off
-      CatSetSplit(CAT_BUFF[4] == 0x02, fromType);
+      CatSetSplit(CAT_BUFF[4] == 0x02);
       break;
 
     case 0x03 :   //Read Frequency and mode
-      CatGetFreqMode(frequency, fromType);
+      CatGetFreqMode(frequency);
       break;
 
     case 0x07 :   //Set Operating  Mode
@@ -713,24 +755,24 @@ void Check_Cat(byte fromType)
       break;
 
     case 0xDB:  //Read uBITX EEPROM Data
-      ReadEEPRom(fromType); //Call by uBITX Manager Program
+      ReadEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBB:  //Read FT-817 EEPROM Data  (for comfirtable)
-      ReadEEPRom_FT817(fromType);
+      ReadEEPRom_FT817();
       break;
 
     case 0xDC:  //Write uBITX EEPROM Data
-      WriteEEPRom(fromType); //Call by uBITX Manager Program
+      WriteEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBC:  //Write FT-817 EEPROM Data  (for comfirtable)
       WriteEEPRom_FT817(fromType);
       break;
 
     case 0xE7 :       //Read RX Status
-      CatRxStatus(fromType);
+      CatRxStatus();
       break;
     case 0xF7:      //Read TX Status
-      CatTxStatus(fromType);
+      CatTxStatus();
       break;
     default:
     /*

ubitx_20/cw_autokey.ino

@@ -1,4 +1,6 @@
 /*************************************************************************
+  KD8CEC's Memory Keyer for HAM
+  
   This source code is written for All amateur radio operator, 
   I have not had amateur radio communication for a long time. CW has been 
   around for a long time, and I do not know what kind of keyer and keying 
@@ -13,6 +15,7 @@
   I wrote this code myself, so there is no license restriction. 
   So this code allows anyone to write with confidence.
   But keep it as long as the original author of the code.
+  DE Ian KD8CEC
 -----------------------------------------------------------------------------
    This program is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
@@ -296,7 +299,11 @@ void controlAutoCW(){
           
           printLineFromEEPRom(0, 2, cwStartIndex + displayScrolStep + CW_DATA_OFSTADJ, cwEndIndex + CW_DATA_OFSTADJ); 
 
-          lcd.setCursor(0,0);
+          byte diplayAutoCWLine = 0;
+          if ((displayOption1 & 0x01) == 0x01)
+            diplayAutoCWLine = 1;
+          
+          lcd.setCursor(0, diplayAutoCWLine);
           lcd.write(byteToChar(selectedCWTextIndex));
           lcd.write(':');
           isNeedScroll = (cwEndIndex - cwStartIndex) > 14 ? 1 : 0;
@@ -358,6 +365,11 @@ void controlAutoCW(){
         //check interval time, if you want adjust interval between chars, modify below
         if (isAutoCWHold == 0 && (millis() - autoCWbeforeTime > cwSpeed * 3))
         {
+          if (!inTx){                                           //if not TX Status, change RX -> TX
+            keyDown = 0;
+            startTx(TX_CW, 0);  //disable updateDisplay Command for reduce latency time
+          }
+          
           sendCWChar(EEPROM.read(CW_AUTO_DATA + autoCWSendCharIndex++));
 
           if (autoCWSendCharIndex > autoCWSendCharEndIndex) {          //finish auto cw send

ubitx_20/ubitx_20.ino

@@ -1,4 +1,10 @@
 /**
+ Since KD8CEC Version 0.29, most of the original code is no longer available.
+ Most features(TX, Frequency Range, Ham Band, TX Control, CW delay, start Delay... more) have been added by KD8CEC.
+ However, the license rules are subject to the original source rules.
+ DE Ian KD8CEC
+
+ Original source comment            -------------------------------------------------------------
  * This source file is under General Public License version 3.
  * 
  * This verision uses a built-in Si5351 library
@@ -78,6 +84,7 @@
 #define PTT   (A3)
 #define ANALOG_KEYER (A6)
 #define ANALOG_SPARE (A7)
+#define ANALOG_SMETER (A7)  //by KD8CEC
 
 /** 
  * The Raduino board is the size of a standard 16x2 LCD panel. It has three connectors:
@@ -144,15 +151,42 @@ int count = 0;          //to generally count ticks, loops, etc
 #define CW_SPEED 28
 
 //AT328 has 1KBytes EEPROM
+#define CW_CAL 252
 #define VFO_A_MODE 256
 #define VFO_B_MODE 257
 #define CW_DELAY 258
 #define CW_START 259
-#define HAM_BAND_COUNT 260  //
-#define TX_TUNE_TYPE 261  //
-#define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
-#define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP 342   //TUNING STEP * 6 (index 1 + STEPS 5)
+#define HAM_BAND_COUNT 260    //
+#define TX_TUNE_TYPE 261      //
+#define HAM_BAND_RANGE 262    //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
+#define HAM_BAND_FREQS 302    //40, 1 BAND = 4Byte most bit is mode
+#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+  
+
+//for reduce cw key error, eeprom address
+#define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
+#define CW_ADC_ST_FROM   349   //CW ADC Range STRAIGHT KEY from (Lower 8 bit)
+#define CW_ADC_ST_TO     350   //CW ADC Range STRAIGHT KEY to   (Lower 8 bit)
+#define CW_ADC_DOT_FROM  351   //CW ADC Range DOT  from         (Lower 8 bit)
+#define CW_ADC_DOT_TO    352   //CW ADC Range DOT  to           (Lower 8 bit)
+
+#define CW_ADC_MOST_BIT2 353   //most 2bits of BOTH_TO, BOTH_FROM, DASH_TO, DASH_FROM
+#define CW_ADC_DASH_FROM 354   //CW ADC Range DASH from         (Lower 8 bit)
+#define CW_ADC_DASH_TO   355   //CW ADC Range DASH to           (Lower 8 bit)
+#define CW_ADC_BOTH_FROM 356   //CW ADC Range BOTH from         (Lower 8 bit)
+#define CW_ADC_BOTH_TO   357   //CW ADC Range BOTH to           (Lower 8 bit)
+#define CW_KEY_TYPE      358
+#define CW_DISPLAY_SHIFT 359  //Transmits on CWL, CWU Mode, LCD Frequency shifts Sidetone Frequency. 
+                              //(7:Enable / Disable //0: enable, 1:disable, (default is applied shift)
+                              //6 : 0 : Adjust Pulus, 1 : Adjust Minus
+                              //0~5: Adjust Value : * 10 = Adjust Value (0~300)
+
+#define DISPLAY_OPTION1  361   //Display Option1
+#define DISPLAY_OPTION2  362   //Display Option2
+
+#define CHANNEL_FREQ    630   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define CHANNEL_DESC    710   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define RESERVE3        770   //Reserve3 between Channel and Firmware id check
 
 //Check Firmware type and version
 #define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
@@ -208,7 +242,7 @@ int count = 0;          //to generally count ticks, loops, etc
 char ritOn = 0;
 char vfoActive = VFO_A;
 int8_t meter_reading = 0; // a -1 on meter makes it invisible
-unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier;
+unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier, cwmCarrier;
 unsigned long vfoA_eeprom, vfoB_eeprom; //for protect eeprom life
 unsigned long frequency, ritRxFrequency, ritTxFrequency;  //frequency is the current frequency on the dial
 
@@ -225,7 +259,6 @@ byte saveIntervalSec = 10;  //second
 unsigned long saveCheckTime = 0;
 unsigned long saveCheckFreq = 0;
 
-bool isSplitOn = false;
 byte cwDelayTime = 60;
 byte delayBeforeCWStartTime = 50;
 
@@ -236,9 +269,29 @@ byte sideToneSub = 0;
 //DialLock
 byte isDialLock = 0;  //000000[0]vfoB [0]vfoA 0Bit : A, 1Bit : B
 byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
-byte arTuneStep[5];
+long arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
+byte displayOption1 = 0;
+byte displayOption2 = 0;
+
+//CW ADC Range
+int cwAdcSTFrom = 0;
+int cwAdcSTTo = 0;
+int cwAdcDotFrom = 0;
+int cwAdcDotTo = 0;
+int cwAdcDashFrom = 0;
+int cwAdcDashTo = 0;
+int cwAdcBothFrom = 0;
+int cwAdcBothTo = 0;
+byte cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+bool Iambic_Key = true;
+#define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
+unsigned char keyerControl = IAMBICB;
+
+byte isShiftDisplayCWFreq = 1;  //Display Frequency 
+int shiftDisplayAdjustVal = 0;  //
+
 //Variables for auto cw mode
 byte isCWAutoMode = 0;          //0 : none, 1 : CW_AutoMode_Menu_Selection, 2 : CW_AutoMode Sending
 byte cwAutoTextCount = 0;       //cwAutoText Count
@@ -257,9 +310,13 @@ byte userCallsignLength = 0;    //7 : display callsign at system startup, 6~0 :
  */
 boolean txCAT = false;        //turned on if the transmitting due to a CAT command
 char inTx = 0;                //it is set to 1 if in transmit mode (whatever the reason : cw, ptt or cat)
-char splitOn = 0;             //working split, uses VFO B as the transmit frequency, (NOT IMPLEMENTED YET)
+char splitOn = 0;             //working split, uses VFO B as the transmit frequency
 char keyDown = 0;             //in cw mode, denotes the carrier is being transmitted
 char isUSB = 0;               //upper sideband was selected, this is reset to the default for the 
+
+char cwMode = 0;              //compatible original source, and extend mode //if cwMode == 0, mode check : isUSB, cwMode > 0, mode Check : cwMode
+                              //iscwMode = 0 : ssbmode, 1 :cwl, 2 : cwu, 3 : cwn (none tx)
+                              
                               //frequency when it crosses the frequency border of 10 MHz
 byte menuOn = 0;              //set to 1 when the menu is being displayed, if a menu item sets it to zero, the menu is exited
 unsigned long cwTimeout = 0;  //milliseconds to go before the cw transmit line is released and the radio goes back to rx mode
@@ -267,6 +324,14 @@ unsigned long dbgCount = 0;   //not used now
 unsigned char txFilter = 0;   //which of the four transmit filters are in use
 boolean modeCalibrate = false;//this mode of menus shows extended menus to calibrate the oscillators and choose the proper
                               //beat frequency
+
+unsigned long beforeIdle_ProcessTime = 0; //for check Idle time
+byte line2DisplayStatus = 0;  //0:Clear, 1 : menu, 1: DisplayFrom Idle, 
+char lcdMeter[17];
+
+byte isIFShift = 0;     //1 = ifShift, 2 extend
+long ifShiftValue = 0;  //
+                              
 /**
  * Below are the basic functions that control the uBitx. Understanding the functions before 
  * you start hacking around
@@ -319,29 +384,30 @@ void setNextHamBandFreq(unsigned long f, char moveDirection)
 
   EEPROM.get(HAM_BAND_FREQS + 4 * findedIndex, resultFreq);
   
-  loadMode = (byte)(resultFreq >> 30);
-  resultFreq = resultFreq & 0x3FFFFFFF;
+  //loadMode = (byte)(resultFreq >> 30);
+  //resultFreq = resultFreq & 0x3FFFFFFF;
+  loadMode = (byte)(resultFreq >> 29);
+  resultFreq = resultFreq & 0x1FFFFFFF;
   
   if ((resultFreq / 1000) < hamBandRange[(unsigned char)findedIndex][0] || (resultFreq / 1000) > hamBandRange[(unsigned char)findedIndex][1])
     resultFreq = (unsigned long)(hamBandRange[(unsigned char)findedIndex][0]) * 1000;
 
   setFrequency(resultFreq);
-  byteWithFreqToMode(loadMode);
+  byteToMode(loadMode, 1);
 }
 
 void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
   if (bandIndex >= 0)
-    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    //EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x1FFFFFFF) | (mode << 29) );
 }
 
-
 /*
   KD8CEC
   When using the basic delay of the Arduino, the program freezes.
   When the delay is used, the program will generate an error because it is not communicating, 
   so Create a new delay function that can do background processing.
  */
- 
 unsigned long delayBeforeTime = 0;
 byte delay_background(unsigned delayTime, byte fromType){ //fromType : 4 autoCWKey -> Check Paddle
   delayBeforeTime = millis();
@@ -428,13 +494,27 @@ void setFrequency(unsigned long f){
   
   setTXFilters(f);
 
-  if (isUSB){
-    si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_USB);
+  if (cwMode == 0)
+  {
+    if (isUSB){
+      si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f  + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
+    else{
+      si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
   }
-  else{
-    si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_LSB);
+  else
+  {
+    if (cwMode == 1){ //CWL
+      si5351bx_setfreq(2, SECOND_OSC_LSB + cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
+    else{             //CWU
+      si5351bx_setfreq(2, SECOND_OSC_USB - cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
   }
   
   frequency = f;
@@ -445,7 +525,6 @@ void setFrequency(unsigned long f){
  * put the uBitx in tx mode. It takes care of rit settings, sideband settings
  * Note: In cw mode, doesnt key the radio, only puts it in tx mode
  */
- 
 void startTx(byte txMode, byte isDisplayUpdate){
   //Check Hamband only TX //Not found Hamband index by now frequency
   if (tuneTXType >= 100 && getIndexHambanBbyFreq(ritOn ? ritTxFrequency :  frequency) == -1) {
@@ -463,6 +542,21 @@ void startTx(byte txMode, byte isDisplayUpdate){
     ritRxFrequency = frequency;
     setFrequency(ritTxFrequency);
   }
+  else if (splitOn == 1) {
+      if (vfoActive == VFO_B) {
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+
+      setFrequency(frequency);
+  } //end of else
+  
 
   if (txMode == TX_CW){
     //turn off the second local oscillator and the bfo
@@ -472,10 +566,22 @@ void startTx(byte txMode, byte isDisplayUpdate){
     //shif the first oscillator to the tx frequency directly
     //the key up and key down will toggle the carrier unbalancing
     //the exact cw frequency is the tuned frequency + sidetone
-    if (isUSB)
-      si5351bx_setfreq(2, frequency + sideTone);
-    else
-      si5351bx_setfreq(2, frequency - sideTone); 
+
+    if (cwMode == 0)
+    {
+      if (isUSB)
+        si5351bx_setfreq(2, frequency + sideTone);
+      else
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else if (cwMode == 1) //CWL
+    {
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else  //CWU
+    {
+        si5351bx_setfreq(2, frequency + sideTone);
+    }
   }
 
   //reduce latency time when begin of CW mode
@@ -487,10 +593,28 @@ void stopTx(){
   inTx = 0;
 
   digitalWrite(TX_RX, 0);           //turn off the tx
-  si5351bx_setfreq(0, usbCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
+  else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
 
   if (ritOn)
     setFrequency(ritRxFrequency);
+  else if (splitOn == 1) {
+      //vfo Change
+      if (vfoActive == VFO_B){
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+      setFrequency(frequency);
+  } //end of else
   else
     setFrequency(frequency);
   
@@ -556,7 +680,7 @@ void checkButton(){
     delay(10);
     Check_Cat(0);
   }
-  delay(50);//debounce
+  //delay(50);//debounce
 }
 
 
@@ -568,11 +692,15 @@ applied Threshold for reduct errors,  dial Lock, dynamic Step
 byte threshold = 2;  //noe action for count
 unsigned long lastEncInputtime = 0;
 int encodedSumValue = 0;
+unsigned long lastTunetime = 0; //if continous moving, skip threshold processing
+byte lastMovedirection = 0; //0 : stop, 1 : cw, 2 : ccw
+
+//#define skipThresholdTime 70
 #define encodeTimeOut 1000
-void doTuning(){
+
+void doTuningWithThresHold(){
   int s = 0;
   unsigned long prev_freq;
-  long incdecValue = 0;
 
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02)))
@@ -586,6 +714,8 @@ void doTuning(){
   if (s == 0) {
     if (encodedSumValue != 0 && (millis() - encodeTimeOut) > lastEncInputtime)
       encodedSumValue = 0;
+
+    lastMovedirection = 0;
     return;
   }
   lastEncInputtime = millis();
@@ -593,16 +723,21 @@ void doTuning(){
   //for check moving direction
   encodedSumValue += (s > 0 ? 1 : -1);
 
-  //check threshold
-  if ((encodedSumValue *  encodedSumValue) <= (threshold * threshold))
+  //check threshold and operator actions (hold dial speed = continous moving, skip threshold check)
+  //not use continues changing by Threshold
+  //if ((lastTunetime < (millis() - skipThresholdTime)) && ((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
+  if (((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
     return;
 
+  lastTunetime = millis();
+
   //Valid Action without noise
   encodedSumValue = 0;
 
   prev_freq = frequency;
   //incdecValue = tuningStep * s;
-  frequency += (arTuneStep[tuneStepIndex -1] * s);
+  //frequency += (arTuneStep[tuneStepIndex -1] * s * (s * s < 10 ? 1 : 3));  //appield weight (s is speed)
+  frequency += (arTuneStep[tuneStepIndex -1] * s);  //appield weight (s is speed) //if want need more increase size, change step size
     
   if (prev_freq < 10000000l && frequency > 10000000l)
     isUSB = true;
@@ -622,9 +757,9 @@ void doRIT(){
   unsigned long old_freq = frequency;
 
   if (knob < 0)
-    frequency -= 100l;
+    frequency -= (arTuneStep[tuneStepIndex -1]);  //
   else if (knob > 0)
-    frequency += 100;
+    frequency += (arTuneStep[tuneStepIndex -1]);  //
  
   if (old_freq != frequency){
     setFrequency(frequency);
@@ -632,8 +767,8 @@ void doRIT(){
   }
 }
 
-/**
- save Frequency and mode to eeprom
+/*
+ save Frequency and mode to eeprom for Auto Save with protected eeprom cycle, by kd8cec
  */
 void storeFrequencyAndMode(byte saveType)
 {
@@ -665,6 +800,22 @@ void storeFrequencyAndMode(byte saveType)
   }
 }
 
+//calculate step size from 1 byte, compatible uBITX Manager, by KD8CEC
+unsigned int byteToSteps(byte srcByte) {
+    byte powerVal = (byte)(srcByte >> 6);
+    unsigned int baseVal = srcByte & 0x3F;
+
+    if (powerVal == 1)
+        return baseVal * 10;
+    else if (powerVal == 2)
+        return baseVal * 100;
+    else if (powerVal == 3)
+        return baseVal * 1000;
+    else
+        return baseVal;
+}
+
+
 /**
  * The settings are read from EEPROM. The first time around, the values may not be 
  * present or out of range, in this case, some intelligent defaults are copied into the 
@@ -680,7 +831,10 @@ void initSettings(){
   EEPROM.get(VFO_B, vfoB);
   EEPROM.get(CW_SIDETONE, sideTone);
   EEPROM.get(CW_SPEED, cwSpeed);
+  //End of original code
   
+  //----------------------------------------------------------------
+  //Add Lines by KD8CEC
   //for custom source Section =============================
   //ID & Version Check from EEProm 
   //if found different firmware, erase eeprom (32
@@ -704,6 +858,7 @@ void initSettings(){
   if (EEPROM.read(VERSION_ADDRESS) != VERSION_NUM)
     EEPROM.write(VERSION_ADDRESS, VERSION_NUM);
 
+  EEPROM.get(CW_CAL, cwmCarrier);
 
   //for Save VFO_A_MODE to eeprom
   //0: default, 1:not use, 2:LSB, 3:USB, 4:CW, 5:AM, 6:FM
@@ -715,6 +870,24 @@ void initSettings(){
 
   //CW interval between TX and CW Start
   EEPROM.get(CW_START, delayBeforeCWStartTime);
+  EEPROM.get(CW_KEY_TYPE, cwKeyType);
+  if (cwKeyType > 2)
+    cwKeyType = 0;
+
+  if (cwKeyType == 0)
+    Iambic_Key = false;
+  else
+  {
+    Iambic_Key = true;
+    if (cwKeyType == 1)
+      keyerControl &= ~IAMBICB;
+    else
+      keyerControl |= IAMBICB;
+  }
+    
+
+  EEPROM.get(DISPLAY_OPTION1, displayOption1);
+  EEPROM.get(DISPLAY_OPTION2, displayOption2);
 
   //User callsign information
   if (EEPROM.read(USER_CALLSIGN_KEY) == 0x59)
@@ -743,13 +916,13 @@ void initSettings(){
   if ((3 < tuneTXType && tuneTXType < 100) || 103 < tuneTXType || useHamBandCount < 1 || findedValidValueCount < 5)
   {
     tuneTXType = 2;
-    //if empty band Information, auto insert default region 1 frequency range
+    //if empty band Information, auto insert default region 2 frequency range
     //This part is made temporary for people who have difficulty setting up, so can remove it when you run out of memory.
     useHamBandCount = 10;
     hamBandRange[0][0] = 1810; hamBandRange[0][1] = 2000; 
     hamBandRange[1][0] = 3500; hamBandRange[1][1] = 3800; 
     hamBandRange[2][0] = 5351; hamBandRange[2][1] = 5367; 
-    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7200; 
+    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;     //region 2
     hamBandRange[4][0] = 10100; hamBandRange[4][1] = 10150; 
     hamBandRange[5][0] = 14000; hamBandRange[5][1] = 14350; 
     hamBandRange[6][0] = 18068; hamBandRange[6][1] = 18168; 
@@ -763,8 +936,8 @@ void initSettings(){
   findedValidValueCount = 0;
   EEPROM.get(TUNING_STEP, tuneStepIndex);
   for (byte i = 0; i < 5; i++) {
-    arTuneStep[i] = EEPROM.read(TUNING_STEP + i + 1);
-    if (arTuneStep[i] >= 1 && arTuneStep[i] < 251) //Maximum 250 for check valid Value
+    arTuneStep[i] = byteToSteps(EEPROM.read(TUNING_STEP + i + 1));
+    if (arTuneStep[i] >= 1 && arTuneStep[i] <= 60000) //Maximum 650 for check valid Value
        findedValidValueCount++;
   }
 
@@ -782,6 +955,61 @@ void initSettings(){
   if (tuneStepIndex == 0) //New User
     tuneStepIndex = 3;
 
+  //CW Key ADC Range ======= adjust set value for reduce cw keying error
+  //by KD8CEC
+  unsigned int tmpMostBits = 0;
+  tmpMostBits = EEPROM.read(CW_ADC_MOST_BIT1);
+  cwAdcSTFrom = EEPROM.read(CW_ADC_ST_FROM)   | ((tmpMostBits & 0x03) << 8);
+  cwAdcSTTo = EEPROM.read(CW_ADC_ST_TO)       | ((tmpMostBits & 0x0C) << 6);
+  cwAdcDotFrom = EEPROM.read(CW_ADC_DOT_FROM) | ((tmpMostBits & 0x30) << 4);
+  cwAdcDotTo = EEPROM.read(CW_ADC_DOT_TO)     | ((tmpMostBits & 0xC0) << 2);
+  
+  tmpMostBits = EEPROM.read(CW_ADC_MOST_BIT2);
+  cwAdcDashFrom = EEPROM.read(CW_ADC_DASH_FROM) | ((tmpMostBits & 0x03) << 8);
+  cwAdcDashTo = EEPROM.read(CW_ADC_DASH_TO)     | ((tmpMostBits & 0x0C) << 6);
+  cwAdcBothFrom = EEPROM.read(CW_ADC_BOTH_FROM) | ((tmpMostBits & 0x30) << 4);
+  cwAdcBothTo = EEPROM.read(CW_ADC_BOTH_TO)     | ((tmpMostBits & 0xC0) << 2);
+
+  //Display Type for CW mode
+  isShiftDisplayCWFreq = EEPROM.read(CW_DISPLAY_SHIFT);
+
+  //Adjust CW Mode Freq
+  shiftDisplayAdjustVal = (isShiftDisplayCWFreq & 0x3F) * 10;
+
+  //check Minus
+  if ((isShiftDisplayCWFreq & 0x40) == 0x40)
+    shiftDisplayAdjustVal = shiftDisplayAdjustVal * -1;
+
+ //Shift Display Check (Default : 0)
+  if ((isShiftDisplayCWFreq & 0x80) == 0)  //Enabled
+    isShiftDisplayCWFreq = 1;
+  else    //Disabled
+    isShiftDisplayCWFreq = 0;
+
+  //default Value (for original hardware)
+  if (cwAdcSTFrom >= cwAdcSTTo)
+  {
+    cwAdcSTFrom = 0;
+    cwAdcSTTo = 50;
+  }
+
+  if (cwAdcBothFrom >= cwAdcBothTo)
+  {
+    cwAdcBothFrom = 51;
+    cwAdcBothTo = 300;
+  }
+  
+  if (cwAdcDotFrom >= cwAdcDotTo)
+  {
+    cwAdcDotFrom = 301;
+    cwAdcDotTo = 600;
+  }
+  if (cwAdcDashFrom >= cwAdcDashTo)
+  {
+    cwAdcDashFrom = 601;
+    cwAdcDashTo = 800;
+  }
+  //end of CW Keying Variables
   
   if (cwDelayTime < 1 || cwDelayTime > 250)
     cwDelayTime = 60;
@@ -792,20 +1020,25 @@ void initSettings(){
   if (vfoB_mode < 2)
     vfoB_mode = 3;
 
+  //original code with modified by kd8cec
   if (usbCarrier > 12010000l || usbCarrier < 11990000l)
     usbCarrier = 11995000l;
 
+  if (cwmCarrier > 12010000l || cwmCarrier < 11990000l)
+    cwmCarrier = 11995000l;
+    
   if (vfoA > 35000000l || 3500000l > vfoA) {
      vfoA = 7150000l;
-     vfoA_mode = 2;
+     vfoA_mode = 2; //LSB
   }
   
   if (vfoB > 35000000l || 3500000l > vfoB) {
      vfoB = 14150000l;  
-     vfoB_mode = 3;
+     vfoB_mode = 3; //USB
   }
+  //end of original code section
 
-  //for protect eeprom life
+  //for protect eeprom life by KD8CEC
   vfoA_eeprom = vfoA;
   vfoB_eeprom = vfoB;
   vfoA_mode_eeprom = vfoA_mode;
@@ -827,7 +1060,6 @@ void initSettings(){
 }
 
 void initPorts(){
-
   analogReference(DEFAULT);
 
   //??
@@ -841,6 +1073,7 @@ void initPorts(){
 
   pinMode(PTT, INPUT_PULLUP);
   pinMode(ANALOG_KEYER, INPUT_PULLUP);
+  pinMode(ANALOG_SMETER, INPUT); //by KD8CEC
 
   pinMode(CW_TONE, OUTPUT);  
   digitalWrite(CW_TONE, 0);
@@ -876,7 +1109,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.27")); 
+  printLineF(1, F("CECBT v1.04")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -890,15 +1123,16 @@ void setup()
   else {
     printLineF(0, F("uBITX v0.20")); 
     delay(500);
-    printLine2(""); 
+    clearLine2();
   }
   
   initPorts();     
+
+  byteToMode(vfoA_mode, 0);
   initOscillators();
 
   frequency = vfoA;
   saveCheckFreq = frequency;  //for auto save frequency
-  byteToMode(vfoA_mode);
   setFrequency(vfoA);
   updateDisplay();
 
@@ -906,14 +1140,7 @@ void setup()
     factory_alignment();
 }
 
-
-/**
- * The loop checks for keydown, ptt, function button and tuning.
- */
-//for debug
-int dbgCnt = 0;
-byte flasher = 0;
-
+//Auto save Frequency and Mode with Protected eeprom life by KD8CEC
 void checkAutoSaveFreqMode()
 {
   //when tx or ritOn, disable auto save
@@ -931,18 +1158,8 @@ void checkAutoSaveFreqMode()
     //check time for Frequency auto save
     if (millis() - saveCheckTime > saveIntervalSec * 1000)
     {
-      if (vfoActive == VFO_A)
-      {
-        vfoA = frequency;
-        vfoA_mode = modeToByte();
-        storeFrequencyAndMode(1);
-      }
-      else
-      {
-        vfoB = frequency;
-        vfoB_mode = modeToByte();
-        storeFrequencyAndMode(2);
-      }
+      FrequencyToVFO(1);
+      saveCheckTime = 0;  //for reduce cpu use rate
     }
   }
 }
@@ -962,11 +1179,18 @@ void loop(){
   if (!inTx){
     if (ritOn)
       doRIT();
+    //else if (isIFShift)
+    //  doIFShift();
     else 
-      doTuning();
-  }
+      doTuningWithThresHold();
+
+    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 250) {
+      idle_process();
+      checkAutoSaveFreqMode();  //move here form out scope for reduce cpu use rate
+      beforeIdle_ProcessTime = millis();
+    }
+  } //end of check TX Status
 
   //we check CAT after the encoder as it might put the radio into TX
   Check_Cat(inTx? 1 : 0);
-  checkAutoSaveFreqMode();
 }

ubitx_20/ubitx_factory_alignment.ino

@@ -14,6 +14,7 @@ void btnWaitForClick(){
 void factory_alignment(){
         
   factoryCalibration(1);
+  line2DisplayStatus = 1;
 
   if (calibration == 0){
     printLine2("Setup Aborted");
@@ -36,6 +37,7 @@ void factory_alignment(){
 
   
   printLine2("#3:Test 3.5MHz");
+  cwMode = 0;
   isUSB = false;
   setFrequency(3500000l);
   updateDisplay();
@@ -58,6 +60,7 @@ void factory_alignment(){
   btnWaitForClick();
   printLine2("#5:Test 14MHz");
 
+  cwMode = 0;
   isUSB = true;
   setFrequency(14000000l);
   updateDisplay();
@@ -79,6 +82,7 @@ void factory_alignment(){
   printLine2("Alignment done");
   delay(1000);
 
+  cwMode = 0;
   isUSB = false;
   setFrequency(7150000l);
   updateDisplay();  

ubitx_20/ubitx_idle.ino

@@ -0,0 +1,262 @@
+/*************************************************************************
+  KD8CEC's uBITX Idle time Processing
+  Functions that run at times that do not affect TX, CW, and CAT
+  It is called in 1/10 time unit.
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+**************************************************************************/
+char line2Buffer[16];
+//KD8CEC 200Hz ST
+//L14.150 200Hz ST
+//U14.150 +150khz
+int freqScrollPosition = 0;
+//Example Line2 Optinal Display
+//immediate execution, not call by scheulder
+void updateLine2Buffer(char isDirectCall)
+{
+  unsigned long tmpFreq = 0;
+  if (isDirectCall == 0)
+  {
+    if (ritOn)
+    {
+      strcpy(line2Buffer, "RitTX:");
+      /*
+      line2Buffer[0] = 'R';
+      line2Buffer[1] = 'i';
+      line2Buffer[2] = 't';
+      line2Buffer[3] = 'T';
+      line2Buffer[4] = 'X';
+      line2Buffer[5] = ':';
+      */
+  
+      //display frequency
+      tmpFreq = ritTxFrequency;
+      for (int i = 15; i >= 6; i--) {
+        if (tmpFreq > 0) {
+          if (i == 12 || i == 8) line2Buffer[i] = '.';
+          else {
+            line2Buffer[i] = tmpFreq % 10 + 0x30;
+            tmpFreq /= 10;
+          }
+        }
+        else
+          line2Buffer[i] = ' ';
+      }
+  
+      return;
+    } //end of ritOn display
+
+    //======================================================
+    //other VFO display
+    //======================================================
+    if (vfoActive == VFO_B)
+    {
+      tmpFreq = vfoA;
+    }
+    else 
+    {
+      tmpFreq = vfoB;
+    }
+  
+    // EXAMPLE 1 & 2
+    //U14.150.100
+    //display frequency
+    for (int i = 9; i >= 0; i--) {
+      if (tmpFreq > 0) {
+        if (i == 2 || i == 6) line2Buffer[i] = '.';
+        else {
+          line2Buffer[i] = tmpFreq % 10 + 0x30;
+          tmpFreq /= 10;
+        }
+      }
+      else
+        line2Buffer[i] = ' ';
+    }
+  
+    //EXAMPLE #1
+    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
+      line2Buffer[6] = 'k';
+    else
+    {
+      //example #2
+      if (freqScrollPosition++ > 18)    //none scroll display time
+      {
+        line2Buffer[6] = 'k';
+        if (freqScrollPosition > 25)
+          freqScrollPosition = -1;
+      }
+      else                              //scroll frequency 
+      {
+        line2Buffer[10] = 'H';
+        line2Buffer[11] = 'z';
+    
+        if (freqScrollPosition < 7)   
+        {
+          for (int i = 11; i >= 0; i--)
+            if (i - (7 - freqScrollPosition) >= 0)
+              line2Buffer[i] = line2Buffer[i - (7 - freqScrollPosition)];
+            else
+              line2Buffer[i] = ' ';
+        }
+        else
+        {
+          for (int i = 0; i < 11; i++)
+            if (i + (freqScrollPosition - 7) <= 11)
+              line2Buffer[i] = line2Buffer[i + (freqScrollPosition - 7)];
+            else
+              line2Buffer[i] = ' ';
+        }
+      }
+    } //scroll
+    
+    line2Buffer[7] = ' ';
+  } //check direct call by encoder
+  
+  if (isIFShift)
+  {
+    if (isDirectCall == 1)
+      for (int i = 0; i < 16; i++)
+        line2Buffer[i] = ' ';
+      
+      //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
+
+    //if (ifShiftValue == 0)
+    //{
+      /*
+      line2Buffer[10] = 'S';
+      line2Buffer[11] = ':';
+      line2Buffer[12] = 'O';
+      line2Buffer[13] = 'F';
+      line2Buffer[14] = 'F';
+      */
+    //}
+    //else
+    //{
+      line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+      line2Buffer[11] = 0;
+      line2Buffer[12] = ' ';
+    
+      //11, 12, 13, 14, 15
+      memset(b, 0, sizeof(b));
+      ltoa(ifShiftValue, b, DEC);
+      strncat(line2Buffer, b, 5);
+    //}
+    
+    if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
+        printLine2(line2Buffer);    
+  }       // end of display IF
+  else    // step display
+  {
+    if (isDirectCall != 0)
+      return;
+
+    memset(&line2Buffer[8], ' ', 8);
+    //Step
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
+      if (tmpStep > 0) {
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
+          tmpStep /= 10;
+      }
+      else
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+    //if (isStepKhz == 1)
+    //  line2Buffer[10] = 'k';
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[11] = 'H';
+      line2Buffer[12] = 'z';
+    }
+  
+    line2Buffer[13] = ' ';
+    //if (
+    //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+    if (cwKeyType == 0)
+    {
+      line2Buffer[14] = 'S';
+      line2Buffer[15] = 'T';
+    }
+    else if (cwKeyType == 1)
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'A';
+    }
+    else
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'B';
+    }    
+  }
+  
+}
+
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  if (meterType == 0 || meterType == 1 || meterType == 2)
+  {
+    drawMeter(meterValue);  //call original source code
+    int lineNumber = 0;
+    if ((displayOption1 & 0x01) == 0x01)
+      lineNumber = 1;
+    
+    lcd.setCursor(drawPosition, lineNumber);
+  
+    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+      lcd.write(lcdMeter[i]);
+  }
+}
+
+byte testValue = 0;
+char checkCount = 0;
+void idle_process()
+{
+  //space for user graphic display
+  if (menuOn == 0)
+  {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
+    //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
+    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
+        printLine2(line2Buffer);
+        line2DisplayStatus = 2;
+        checkCount = 0;
+      }
+
+      //EX for Meters
+      /*
+      DisplayMeter(0, testValue++, 7);
+      if (testValue > 30)
+        testValue = 0;
+      */
+    }
+  }
+}
+

ubitx_20/ubitx_keyer.ino

@@ -1,8 +1,9 @@
 /**
- * CW Keyer
- * CW Key logic change with ron's code (ubitx_keyer.cpp) <=== **********************************
- * The file you are working on. The code only applies and is still in testing. <==== ***********
- * 
+ CW Keyer
+ CW Key logic change with ron's code (ubitx_keyer.cpp)
+ Ron's logic has been modified to work with the original uBITX by KD8CEC
+
+ Original Comment ----------------------------------------------------------------------------
  * The CW keyer handles either a straight key or an iambic / paddle key.
  * They all use just one analog input line. This is how it works.
  * The analog line has the internal pull-up resistor enabled. 
@@ -82,204 +83,172 @@ void cwKeyUp(){
   cwTimeout = millis() + cwDelayTime * 10;
 }
 
-/*****************************************************************************
-// New logic, by RON
-// modified by KD8CEC
-******************************************************************************/
+//Variables for Ron's new logic
 #define DIT_L 0x01 // DIT latch
 #define DAH_L 0x02 // DAH latch
 #define DIT_PROC 0x04 // DIT is being processed
 #define PDLSWAP 0x08 // 0 for normal, 1 for swap
 #define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
 enum KSTYPE {IDLE, CHK_DIT, CHK_DAH, KEYED_PREP, KEYED, INTER_ELEMENT };
-
-static long ktimer;
-
-bool Iambic_Key = true;
-unsigned char keyerControl = IAMBICB;
+static unsigned long ktimer;
 unsigned char keyerState = IDLE;
 
-//Below is a test to reduce the keying error.
-/*
-char update_PaddleLatch(byte isUpdateKeyState) {
-  int paddle = analogRead(ANALOG_KEYER);
-  unsigned char tmpKeyerControl;
-
-  if (paddle > 800)               // above 4v is up
-    tmpKeyerControl = 0;
-  //else if (paddle > 600)         // 4-3v is DASH
-  else if (paddle > 693 && paddle < 700)         // 4-3v is DASH
-    tmpKeyerControl |= DAH_L;
-  //else if (paddle > 300)        //1-2v is DOT
-  else if (paddle > 323 && paddle < 328)        //1-2v is DOT
-    tmpKeyerControl |= DIT_L;
-  //else if (paddle > 50)
-  else if (paddle > 280 && paddle < 290)
-    tmpKeyerControl |= (DAH_L | DIT_L) ;     //both are between 1 and 2v
-  else
-    tmpKeyerControl = 0 ;   //STRAIGHT KEY in original code
-    //keyerControl |= (DAH_L | DIT_L) ;   //STRAIGHT KEY in original code
-  
-  if (isUpdateKeyState == 1) {
-    keyerControl |= tmpKeyerControl;
-  }
-
-  byte buff[17];
-  sprintf(buff, "Key : %d", paddle);
-  if (tmpKeyerControl > 0)
-    printLine2(buff);
-  
-  return tmpKeyerControl;
-
-  //if (analogRead(ANALOG_DOT)   < 600 ) keyerControl |= DIT_L;
-  //if (analogRead(ANALOG_DASH)  < 600 ) keyerControl |= DAH_L;
-}
-*/
-
+//Below is a test to reduce the keying error. do not delete lines
 //create by KD8CEC for compatible with new CW Logic
 char update_PaddleLatch(byte isUpdateKeyState) {
+  unsigned char tmpKeyerControl = 0;
   int paddle = analogRead(ANALOG_KEYER);
-  unsigned char tmpKeyerControl;
 
-  if (paddle > 800)               // above 4v is up
-    tmpKeyerControl = 0;
-  else if (paddle > 600)         // 4-3v is DASH
+  if (paddle >= cwAdcDashFrom && paddle <= cwAdcDashTo)
     tmpKeyerControl |= DAH_L;
-  else if (paddle > 300)        //1-2v is DOT
+  else if (paddle >= cwAdcDotFrom && paddle <= cwAdcDotTo)
     tmpKeyerControl |= DIT_L;
-  else if (paddle > 50)
-    tmpKeyerControl |= (DAH_L | DIT_L) ;     //both are between 1 and 2v
+  else if (paddle >= cwAdcBothFrom && paddle <= cwAdcBothTo)
+    tmpKeyerControl |= (DAH_L | DIT_L) ;     
   else 
-    tmpKeyerControl = 0 ;   //STRAIGHT KEY in original code
-    //keyerControl |= (DAH_L | DIT_L) ;   //STRAIGHT KEY in original code
-  
-  if (isUpdateKeyState == 1) {
-    keyerControl |= tmpKeyerControl;
+  {
+    if (Iambic_Key)
+      tmpKeyerControl = 0 ;
+    else if (paddle >= cwAdcSTFrom && paddle <= cwAdcSTTo)
+      tmpKeyerControl = DIT_L ;
+     else
+       tmpKeyerControl = 0 ; 
   }
   
+  if (isUpdateKeyState == 1)
+    keyerControl |= tmpKeyerControl;
+
   return tmpKeyerControl;
-  //if (analogRead(ANALOG_DOT)   < 600 ) keyerControl |= DIT_L;
-  //if (analogRead(ANALOG_DASH)  < 600 ) keyerControl |= DAH_L;
 }
 
+/*****************************************************************************
+// New logic, by RON
+// modified by KD8CEC
+******************************************************************************/
 void cwKeyer(void){
-  byte paddle;
   lastPaddle = 0;
-  int dot,dash;
   bool continue_loop = true;
   unsigned tmpKeyControl = 0;
-if( Iambic_Key ){
   
-while(continue_loop){
-  switch (keyerState) {
-    case IDLE:
-      tmpKeyControl = update_PaddleLatch(0);
-      if ( tmpKeyControl == DAH_L || tmpKeyControl == DIT_L || 
-        tmpKeyControl == (DAH_L | DIT_L) || (keyerControl & 0x03)) {
-        //DIT or DASH or current state DIT & DASH
-        //(analogRead(ANALOG_DOT)  < 600) ||  //DIT
-        //(analogRead(ANALOG_DASH)  < 600) || //DIT
-        //   (keyerControl & 0x03)) {
-         update_PaddleLatch(1);
-         keyerState = CHK_DIT;
-      }else{
+  if( Iambic_Key ) {
+    while(continue_loop) {
+      switch (keyerState) {
+        case IDLE:
+          tmpKeyControl = update_PaddleLatch(0);
+          if ( tmpKeyControl == DAH_L || tmpKeyControl == DIT_L || 
+            tmpKeyControl == (DAH_L | DIT_L) || (keyerControl & 0x03)) {
+             update_PaddleLatch(1);
+             keyerState = CHK_DIT;
+          }else{
+            if (0 < cwTimeout && cwTimeout < millis()){
+              cwTimeout = 0;
+              stopTx();
+            }
+            continue_loop = false;
+          }
+          break;
+    
+        case CHK_DIT:
+          if (keyerControl & DIT_L) {
+            keyerControl |= DIT_PROC;
+            ktimer = cwSpeed;
+            keyerState = KEYED_PREP;
+          }else{
+            keyerState = CHK_DAH;
+          }
+          break;
+    
+        case CHK_DAH:
+          if (keyerControl & DAH_L) {
+            ktimer = cwSpeed*3;
+            keyerState = KEYED_PREP;
+          }else{
+            keyerState = IDLE;
+          }
+          break;
+    
+        case KEYED_PREP:
+          ktimer += millis(); // set ktimer to interval end time
+          keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
+          keyerState = KEYED; // next state
+          if (!inTx){
+            //DelayTime Option
+            delay_background(delayBeforeCWStartTime * 2, 2);
+            
+            keyDown = 0;
+            cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
+            startTx(TX_CW, 1);
+          }
+          cwKeydown();
+          break;
+    
+        case KEYED:
+          if (millis() > ktimer) { // are we at end of key down ?
+           cwKeyUp();
+           ktimer = millis() + cwSpeed; // inter-element time
+            keyerState = INTER_ELEMENT; // next state
+          }else if (keyerControl & IAMBICB) {
+            update_PaddleLatch(1); // early paddle latch in Iambic B mode
+          }
+          break;
+    
+        case INTER_ELEMENT:
+          // Insert time between dits/dahs
+          update_PaddleLatch(1); // latch paddle state
+          if (millis() > ktimer) { // are we at end of inter-space ?
+            if (keyerControl & DIT_PROC) { // was it a dit or dah ?
+              keyerControl &= ~(DIT_L + DIT_PROC); // clear two bits
+              keyerState = CHK_DAH; // dit done, check for dah
+            }else{
+              keyerControl &= ~(DAH_L); // clear dah latch
+              keyerState = IDLE; // go idle
+            }
+          }
+          break;
+      }
+  
+      Check_Cat(2);
+    } //end of while
+  }
+  else{
+    while(1){
+      if (update_PaddleLatch(0) == DIT_L) {
+        // if we are here, it is only because the key is pressed
+        if (!inTx){
+          //DelayTime Option
+          delay_background(delayBeforeCWStartTime * 2, 2);
+          
+          keyDown = 0;
+          cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT; 
+          startTx(TX_CW, 1);
+        }
+        cwKeydown();
+        
+        while ( update_PaddleLatch(0) == DIT_L ) 
+          delay_background(1, 3);
+          
+        cwKeyUp();
+      }
+      else{
         if (0 < cwTimeout && cwTimeout < millis()){
           cwTimeout = 0;
+          keyDown = 0;
           stopTx();
         }
-        continue_loop = false;
+        //if (!cwTimeout) //removed by KD8CEC
+        //   return;
+        // got back to the beginning of the loop, if no further activity happens on straight key
+        // we will time out, and return out of this routine 
+        //delay(5);
+        //delay_background(5, 3); //removed by KD8CEC
+        //continue;               //removed by KD8CEC
+        return;                   //Tx stop control by Main Loop
       }
-      break;
 
-    case CHK_DIT:
-      if (keyerControl & DIT_L) {
-        keyerControl |= DIT_PROC;
-        ktimer = cwSpeed;
-        keyerState = KEYED_PREP;
-      }else{
-        keyerState = CHK_DAH;
-      }
-      break;
-
-    case CHK_DAH:
-      if (keyerControl & DAH_L) {
-        ktimer = cwSpeed*3;
-        keyerState = KEYED_PREP;
-      }else{
-        keyerState = IDLE;
-      }
-      break;
-
-    case KEYED_PREP:
-      ktimer += millis(); // set ktimer to interval end time
-      keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
-      keyerState = KEYED; // next state
-      if (!inTx){
-        keyDown = 0;
-        cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
-        startTx(TX_CW, 0);
-      }
-      cwKeydown();
-      break;
-
-    case KEYED:
-      if (millis() > ktimer) { // are we at end of key down ?
-       cwKeyUp();
-       ktimer = millis() + cwSpeed; // inter-element time
-        keyerState = INTER_ELEMENT; // next state
-      }else if (keyerControl & IAMBICB) {
-        update_PaddleLatch(1); // early paddle latch in Iambic B mode
-      }
-      break;
-
-    case INTER_ELEMENT:
-      // Insert time between dits/dahs
-      update_PaddleLatch(1); // latch paddle state
-      if (millis() > ktimer) { // are we at end of inter-space ?
-        if (keyerControl & DIT_PROC) { // was it a dit or dah ?
-          keyerControl &= ~(DIT_L + DIT_PROC); // clear two bits
-          keyerState = CHK_DAH; // dit done, check for dah
-        }else{
-          keyerControl &= ~(DAH_L); // clear dah latch
-          keyerState = IDLE; // go idle
-        }
-      }
-      break;
-  }
-} //end of while
-
-}else{
-  while(1){
-    //if (analogRead(ANALOG_DOT) < 600){
-      if (update_PaddleLatch(0) == DIT_L) {
-      // if we are here, it is only because the key is pressed
-      if (!inTx){
-        keyDown = 0;
-        cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT; 
-        startTx(TX_CW, 0);
-      }
-      // start the transmission)
-      cwKeydown();
-      //while ( analogRead(ANALOG_DOT) < 600 ) delay(1);
-      while ( update_PaddleLatch(0) == DIT_L ) delay(1);
-      cwKeyUp();
-    }else{
-      if (0 < cwTimeout && cwTimeout < millis()){
-        cwTimeout = 0;
-        keyDown = 0;
-        stopTx();
-      }
-      if (!cwTimeout)
-        return;
-      // got back to the beginning of the loop, if no further activity happens on straight key
-      // we will time out, and return out of this routine 
-      delay(5);
-      continue;
-   }
-} //end of else
+      Check_Cat(2);
+    } //end of while
+  }   //end of elese
 }
-}
-
 
 
 //=======================================================================================

ubitx_20/ubitx_si5351.ino

@@ -60,6 +60,7 @@ void i2cWriten(uint8_t reg, uint8_t *vals, uint8_t vcnt) {  // write array
   Wire.endTransmission();
 }
 
+uint8_t  si5351Val[8] = {0, 1, 0, 0, 0, 0, 0, 0}; //for reduce program memory size
 
 void si5351bx_init() {                  // Call once at power-up, start PLLA
   uint32_t msxp1;
@@ -68,11 +69,13 @@ void si5351bx_init() {                  // Call once at power-up, start PLLA
   i2cWrite(3, si5351bx_clken);          // Disable all CLK output drivers
   i2cWrite(183, SI5351BX_XTALPF << 6);  // Set 25mhz crystal load capacitance
   msxp1 = 128 * SI5351BX_MSA - 512;     // and msxp2=0, msxp3=1, not fractional
-  uint8_t  vals[8] = {0, 1, BB2(msxp1), BB1(msxp1), BB0(msxp1), 0, 0, 0};
-  i2cWriten(26, vals, 8);               // Write to 8 PLLA msynth regs
+  //uint8_t  vals[8] = {0, 1, BB2(msxp1), BB1(msxp1), BB0(msxp1), 0, 0, 0};
+  si5351Val[2] = BB2(msxp1);
+  si5351Val[3] = BB1(msxp1);
+  si5351Val[4] = BB0(msxp1);
+  
+  i2cWriten(26, si5351Val, 8);               // Write to 8 PLLA msynth regs
   i2cWrite(177, 0x20);                  // Reset PLLA  (0x80 resets PLLB)
-  // for (reg=16; reg<=23; reg++) i2cWrite(reg, 0x80);    // Powerdown CLK's
-  // i2cWrite(187, 0);                  // No fannout of clkin, xtal, ms0, ms4
 }
 
 void si5351bx_setfreq(uint8_t clknum, uint32_t fout) {  // Set a CLK to fout Hz
@@ -109,7 +112,11 @@ void initOscillators(){
   //initialize the SI5351
   si5351bx_init();
   si5351bx_vcoa = (SI5351BX_XTAL * SI5351BX_MSA) + calibration; // apply the calibration correction factor
-  si5351bx_setfreq(0, usbCarrier);
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));
+ else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));
 }
 
 

ubitx_20/ubitx_ui.ino

@@ -25,8 +25,8 @@ int btnDown(){
  * The current reading of the meter is assembled in the string called meter
  */
 
-//char meter[17];
 
+/*
 const PROGMEM uint8_t s_meter_bitmap[] = {
   B00000,B00000,B00000,B00000,B00000,B00100,B00100,B11011,
   B10000,B10000,B10000,B10000,B10100,B10100,B10100,B11011,
@@ -35,7 +35,18 @@ const PROGMEM uint8_t s_meter_bitmap[] = {
   B00010,B00010,B00010,B00010,B00110,B00110,B00110,B11011,
   B00001,B00001,B00001,B00001,B00101,B00101,B00101,B11011
 };
-PGM_P ps_meter_bitmap = reinterpret_cast<PGM_P>(s_meter_bitmap);
+*/
+
+const PROGMEM uint8_t meters_bitmap[] = {
+  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000 ,   //custom 1
+  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000 ,   //custom 2
+  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100 ,   //custom 3
+  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110 ,   //custom 4
+  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111 ,   //custom 5
+  B01000,  B11100,  B01000,  B00000,  B10111,  B10101,  B10101,  B10111     //custom 6
+};
+
+PGM_P p_metes_bitmap = reinterpret_cast<PGM_P>(meters_bitmap);
 
 const PROGMEM uint8_t lock_bitmap[8] = {
   0b01110,
@@ -60,38 +71,54 @@ void initMeter(){
   lcd.createChar(0, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i);
   lcd.createChar(1, tmpbytes);
 
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 8);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 8);
   lcd.createChar(2, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 16);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 16);
   lcd.createChar(3, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 24);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 24);
   lcd.createChar(4, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 28);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 32);
   lcd.createChar(5, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 32);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 40);
   lcd.createChar(6, tmpbytes);
 }
 
-/**
- * The meter is drawn with special characters.
- * character 1 is used to simple draw the blocks of the scale of the meter
- * characters 2 to 6 are used to draw the needle in positions 1 to within the block
- * This displays a meter from 0 to 100, -1 displays nothing
- */
+//by KD8CEC
+//0 ~ 25 : 30 over : + 10
+void drawMeter(int needle) {
+  //5Char + O over
+  int i;
 
- /*
+  for (i = 0; i < 5; i++) {
+    if (needle >= 5)
+      lcdMeter[i] = 5; //full
+    else if (needle > 0)
+      lcdMeter[i] = needle; //full
+    else  //0
+      lcdMeter[i] = 0x20;
+    
+    needle -= 5;
+  }
+
+  if (needle > 0)
+    lcdMeter[5] = 6;
+  else
+    lcdMeter[5] = 0x20;
+}
+
+/*
 void drawMeter(int8_t needle){
   int16_t best, i, s;
 
@@ -101,21 +128,23 @@ void drawMeter(int8_t needle){
   s = (needle * 4)/10;
   for (i = 0; i < 8; i++){
     if (s >= 5)
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     else if (s >= 0)
-      meter[i] = 2 + s;
+      lcdMeter[i] = 2 + s;
     else
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     s = s - 5;
   }
   if (needle >= 40)
-    meter[i-1] = 6;
-  meter[i] = 0;
+    lcdMeter[i-1] = 6;
+  lcdMeter[i] = 0;
 }
 */
-
 // The generic routine to display one line on the LCD 
 void printLine(unsigned char linenmbr, const char *c) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+    
   if (strcmp(c, printBuff[linenmbr])) {     // only refresh the display when there was a change
     lcd.setCursor(0, linenmbr);             // place the cursor at the beginning of the selected line
     lcd.print(c);
@@ -145,6 +174,9 @@ void printLineF(char linenmbr, const __FlashStringHelper *c)
 
 #define LCD_MAX_COLUMN 16
 void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  
   lcd.setCursor(lcdColumn, linenmbr);
 
   for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
@@ -168,6 +200,12 @@ void printLine2(const char *c){
   printLine(0,c);
 }
 
+void clearLine2()
+{
+  printLine2("");
+  line2DisplayStatus = 0;
+}
+
 //  short cut to print to the first line
 void printLine1Clear(){
   printLine(1,"");
@@ -179,6 +217,7 @@ void printLine2Clear(){
 
 void printLine2ClearAndUpdate(){
   printLine(0, "");
+  line2DisplayStatus = 0;  
   updateDisplay();
 }
 
@@ -194,7 +233,6 @@ char byteToChar(byte srcByte){
 void updateDisplay() {
   // tks Jack Purdum W8TEE
   // replaced fsprint commmands by str commands for code size reduction
-  
   // replace code for Frequency numbering error (alignment, point...) by KD8CEC
   int i;
   unsigned long tmpFreq = frequency; //
@@ -221,10 +259,21 @@ void updateDisplay() {
     if (ritOn)
       strcpy(c, "RIT ");
     else {
-      if (isUSB)
-        strcpy(c, "USB ");
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          strcpy(c, "USB ");
+        else
+          strcpy(c, "LSB ");
+      }
+      else if (cwMode == 1)
+      {
+          strcpy(c, "CWL ");
+      }
       else
-        strcpy(c, "LSB ");
+      {
+          strcpy(c, "CWU ");
+      }
     }
     if (vfoActive == VFO_A) // VFO A is active
       strcat(c, "A:");
@@ -232,6 +281,15 @@ void updateDisplay() {
       strcat(c, "B:");
   }
 
+  //Fixed by Mitani Massaru (JE4SMQ)
+  if (isShiftDisplayCWFreq == 1)
+  {
+    if (cwMode == 1)        //CWL
+        tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+    else if (cwMode == 2)   //CWU
+        tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+  }
+
   //display frequency
   for (int i = 15; i >= 6; i--) {
     if (tmpFreq > 0) {
@@ -251,36 +309,24 @@ void updateDisplay() {
   //  strcat(c, " TX");
   printLine(1, c);
 
+  byte diplayVFOLine = 1;
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayVFOLine = 0;
+
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02))) {
-    lcd.setCursor(5,1);
+    lcd.setCursor(5,diplayVFOLine);
     lcd.write((uint8_t)0);
   }
   else if (isCWAutoMode == 2){
-    lcd.setCursor(5,1);
+    lcd.setCursor(5,diplayVFOLine);
     lcd.write(0x7E);
   }
   else
   {
-    lcd.setCursor(5,1);
+    lcd.setCursor(5,diplayVFOLine);
     lcd.write(":");
   }
-
-/*
-  //now, the second line
-  memset(c, 0, sizeof(c));
-  memset(b, 0, sizeof(b));
-
-  if (inTx)
-    strcat(c, "TX ");
-  else if (ritOn)
-    strcpy(c, "RIT");
-
-  strcpy(c, "      \xff");
-  drawMeter(meter_reading);
-  strcat(c, meter);
-  strcat(c, "\xff");
-  printLine2(c);*/
 }
 
 int enc_prev_state = 3;