Optimized from Version1.03

ubitx_20/cat_libs.ino

@@ -109,7 +109,8 @@ void CatSetFreq(byte fromType)
 //#define BCD_LEN 9
 //PROTOCOL : 0x03
 //Computer <-(frequency)-> TRCV CAT_BUFF
-void CatGetFreqMode(unsigned long freq, byte fromType)
+//void CatGetFreqMode(unsigned long freq, byte fromType)
+void CatGetFreqMode(unsigned long freq) //for remove warning messages
 {
   int i;
   byte tmpValue;
@@ -130,23 +131,40 @@ void CatGetFreqMode(unsigned long freq, byte fromType)
   }
 
   //Mode Check
-  if (isUSB)
-    CAT_BUFF[4] = CAT_MODE_USB;
+  if (cwMode == 0)
+  {
+    if (isUSB)
+      CAT_BUFF[4] = CAT_MODE_USB;
+    else
+      CAT_BUFF[4] = CAT_MODE_LSB;
+  }
+  else if (cwMode == 1)
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
   else
-    CAT_BUFF[4] = CAT_MODE_LSB;
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
 
   SendCatData(5);
 }
 
-void CatSetSplit(boolean isSplit, byte fromType)
+//void CatSetSplit(boolean isSplit, byte fromType)
+void CatSetSplit(boolean isSplit) //for remove warning messages
 {
-
+  if (isSplit)
+    splitOn = 1;
+  else
+    splitOn = 0;
+    
   Serial.write(ACK);
 }
 
 void CatSetPTT(boolean isPTTOn, byte fromType)
 {
-  if (fromType == 2 || fromType == 3) {
+  //
+  if ((!inTx) && (fromType == 2 || fromType == 3)) {
     Serial.write(ACK);  
     return;  
   }
@@ -182,7 +200,7 @@ void CatSetPTT(boolean isPTTOn, byte fromType)
 void CatVFOToggle(boolean isSendACK, byte fromType)
 {
   if (fromType != 2 && fromType != 3) {
-    menuVfoToggle(1, 0);
+    menuVfoToggle(1);
   }  
 
   if (isSendACK)
@@ -198,12 +216,18 @@ void CatSetMode(byte tmpMode, byte fromType)
   
   if (!inTx)
   {
-    if (tmpMode == CAT_MODE_USB)
+    if (tmpMode == CAT_MODE_CW)
     {
+      cwMode = 1;
+    }
+    else if (tmpMode == CAT_MODE_USB)
+    {
+      cwMode = 0;
       isUSB = true;
     }
     else
     {
+      cwMode = 0;
       isUSB = false;
     }
 
@@ -215,7 +239,8 @@ void CatSetMode(byte tmpMode, byte fromType)
 }
 
 //Read EEProm by uBITX Manager Software
-void ReadEEPRom(byte fromType)
+//void ReadEEPRom(byte fromType)
+void ReadEEPRom() //for remove warnings.
 {
   //5BYTES
   //CAT_BUFF[0] [1] [2] [3] [4] //4 COMMAND
@@ -238,7 +263,8 @@ void ReadEEPRom(byte fromType)
 }
 
 //Write just proecess 1byes
-void WriteEEPRom(byte fromType)
+//void WriteEEPRom(byte fromType)
+void WriteEEPRom(void)  //for remove warning
 {
   //5BYTES
   uint16_t eepromStartIndex = CAT_BUFF[0] + CAT_BUFF[1] * 256;
@@ -258,7 +284,8 @@ void WriteEEPRom(byte fromType)
   }
 }
 
-void ReadEEPRom_FT817(byte fromType)
+//void ReadEEPRom_FT817(byte fromType)
+void ReadEEPRom_FT817(void) //for remove warnings
 {
   byte temp0 = CAT_BUFF[0];
   byte temp1 = CAT_BUFF[1];
@@ -358,10 +385,21 @@ void ReadEEPRom_FT817(byte fromType)
       CAT_BUFF[1] = 0xB2;
       break;      case 0x69 : //FM Mic (#29)  Contains 0-100 (decimal) as displayed
     case 0x78 :
-      if (isUSB)
-        CAT_BUFF[0] = CAT_MODE_USB;
-      else
-        CAT_BUFF[0] = CAT_MODE_LSB;
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          CAT_BUFF[0] = CAT_MODE_USB;
+        else
+          CAT_BUFF[0] = CAT_MODE_LSB;
+      }
+      else if (cwMode == 1)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
+      else if (cwMode == 2)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
         
       if (CAT_BUFF[0] != 0) CAT_BUFF[0] = 1 << 5;
       break;
@@ -384,7 +422,7 @@ void ReadEEPRom_FT817(byte fromType)
       //7A  6 ? ?
       //7A  7 SPL On/Off  0 = Off, 1 = On
 
-      CAT_BUFF[0] = (isSplitOn ? 0xFF : 0x7F);
+      CAT_BUFF[0] = (splitOn ? 0xFF : 0x7F);
       break;
     case 0xB3 : //
       CAT_BUFF[0] = 0x00;
@@ -472,7 +510,7 @@ void WriteEEPRom_FT817(byte fromType)
         printLineF2(F("Sidetone set! CAT"));
         EEPROM.put(CW_SIDETONE, sideTone);
         delay(300);                       //If timeout errors occur in the calling software, remove them
-        printLine2("");                   //Ham radio deluxe is the only one that supports this feature yet. and ham radio deluxe has wait time as greater than 500ms
+        clearLine2();
       }
       break;
 
@@ -484,7 +522,8 @@ void WriteEEPRom_FT817(byte fromType)
         printLineF2(F("Sidetone set! CAT"));
         EEPROM.put(CW_SIDETONE, sideTone);
         delay(300);                   //If timeout errors occur in the calling software, remove them
-        printLine2("");               //Ham radio deluxe is the only one that supports this feature yet. and ham radio deluxe has wait time as greater than 500ms
+        clearLine2();
+        line2DisplayStatus = 0;
       }
       break;
 
@@ -504,7 +543,7 @@ void WriteEEPRom_FT817(byte fromType)
       printLineF2(F("CW Speed set!"));
       EEPROM.put(CW_DELAY, cwDelayTime);
       delay(300);
-      printLine2("");
+      clearLine2();
       break;
     case 0x62 : //
       //5-0  CW Speed (4-60 WPM) (#21) From 0 to 38 (HEX) with 0 = 4 WPM and 38 = 60 WPM (1 WPM steps)
@@ -513,7 +552,7 @@ void WriteEEPRom_FT817(byte fromType)
       printLineF2(F("CW Speed set!"));
       EEPROM.put(CW_SPEED, cwSpeed);
       delay(300);
-      printLine2("");
+      clearLine2();
 
       break;
       /*
@@ -572,7 +611,8 @@ void WriteEEPRom_FT817(byte fromType)
   Serial.write(ACK);
 }
 
-void CatRxStatus(byte fromType) 
+//void CatRxStatus(byte fromType) 
+void CatRxStatus(void)  //for remove warning
 {
   byte sMeterValue = 1;
 
@@ -592,7 +632,8 @@ void CatRxStatus(byte fromType)
 }
 
 
-void CatTxStatus(byte fromType)
+//void CatTxStatus(byte fromType)
+void CatTxStatus(void)  //for remove warning
 {
   boolean isHighSWR = false;
   boolean isSplitOn = false;
@@ -693,11 +734,11 @@ void Check_Cat(byte fromType)
       
     case 0x02 : //Split On
     case 0x82:  //Split Off
-      CatSetSplit(CAT_BUFF[4] == 0x02, fromType);
+      CatSetSplit(CAT_BUFF[4] == 0x02);
       break;
 
     case 0x03 :   //Read Frequency and mode
-      CatGetFreqMode(frequency, fromType);
+      CatGetFreqMode(frequency);
       break;
 
     case 0x07 :   //Set Operating  Mode
@@ -714,24 +755,24 @@ void Check_Cat(byte fromType)
       break;
 
     case 0xDB:  //Read uBITX EEPROM Data
-      ReadEEPRom(fromType); //Call by uBITX Manager Program
+      ReadEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBB:  //Read FT-817 EEPROM Data  (for comfirtable)
-      ReadEEPRom_FT817(fromType);
+      ReadEEPRom_FT817();
       break;
 
     case 0xDC:  //Write uBITX EEPROM Data
-      WriteEEPRom(fromType); //Call by uBITX Manager Program
+      WriteEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBC:  //Write FT-817 EEPROM Data  (for comfirtable)
       WriteEEPRom_FT817(fromType);
       break;
 
     case 0xE7 :       //Read RX Status
-      CatRxStatus(fromType);
+      CatRxStatus();
       break;
     case 0xF7:      //Read TX Status
-      CatTxStatus(fromType);
+      CatTxStatus();
       break;
     default:
     /*

ubitx_20/cw_autokey.ino

@@ -298,8 +298,12 @@ void controlAutoCW(){
           }
           
           printLineFromEEPRom(0, 2, cwStartIndex + displayScrolStep + CW_DATA_OFSTADJ, cwEndIndex + CW_DATA_OFSTADJ); 
+
+          byte diplayAutoCWLine = 0;
+          if ((displayOption1 & 0x01) == 0x01)
+            diplayAutoCWLine = 1;
           
-          lcd.setCursor(0,0);
+          lcd.setCursor(0, diplayAutoCWLine);
           lcd.write(byteToChar(selectedCWTextIndex));
           lcd.write(':');
           isNeedScroll = (cwEndIndex - cwStartIndex) > 14 ? 1 : 0;
@@ -361,6 +365,11 @@ void controlAutoCW(){
         //check interval time, if you want adjust interval between chars, modify below
         if (isAutoCWHold == 0 && (millis() - autoCWbeforeTime > cwSpeed * 3))
         {
+          if (!inTx){                                           //if not TX Status, change RX -> TX
+            keyDown = 0;
+            startTx(TX_CW, 0);  //disable updateDisplay Command for reduce latency time
+          }
+          
           sendCWChar(EEPROM.read(CW_AUTO_DATA + autoCWSendCharIndex++));
 
           if (autoCWSendCharIndex > autoCWSendCharEndIndex) {          //finish auto cw send

ubitx_20/ubitx_20.ino

@@ -84,6 +84,7 @@
 #define PTT   (A3)
 #define ANALOG_KEYER (A6)
 #define ANALOG_SPARE (A7)
+#define ANALOG_SMETER (A7)  //by KD8CEC
 
 /** 
  * The Raduino board is the size of a standard 16x2 LCD panel. It has three connectors:
@@ -150,15 +151,17 @@ int count = 0;          //to generally count ticks, loops, etc
 #define CW_SPEED 28
 
 //AT328 has 1KBytes EEPROM
+#define CW_CAL 252
 #define VFO_A_MODE 256
 #define VFO_B_MODE 257
 #define CW_DELAY 258
 #define CW_START 259
-#define HAM_BAND_COUNT 260  //
-#define TX_TUNE_TYPE 261  //
-#define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
-#define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)
+#define HAM_BAND_COUNT 260    //
+#define TX_TUNE_TYPE 261      //
+#define HAM_BAND_RANGE 262    //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
+#define HAM_BAND_FREQS 302    //40, 1 BAND = 4Byte most bit is mode
+#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+  
 
 //for reduce cw key error, eeprom address
 #define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
@@ -172,6 +175,18 @@ int count = 0;          //to generally count ticks, loops, etc
 #define CW_ADC_DASH_TO   355   //CW ADC Range DASH to           (Lower 8 bit)
 #define CW_ADC_BOTH_FROM 356   //CW ADC Range BOTH from         (Lower 8 bit)
 #define CW_ADC_BOTH_TO   357   //CW ADC Range BOTH to           (Lower 8 bit)
+#define CW_KEY_TYPE      358
+#define CW_DISPLAY_SHIFT 359  //Transmits on CWL, CWU Mode, LCD Frequency shifts Sidetone Frequency. 
+                              //(7:Enable / Disable //0: enable, 1:disable, (default is applied shift)
+                              //6 : 0 : Adjust Pulus, 1 : Adjust Minus
+                              //0~5: Adjust Value : * 10 = Adjust Value (0~300)
+
+#define DISPLAY_OPTION1  361   //Display Option1
+#define DISPLAY_OPTION2  362   //Display Option2
+
+#define CHANNEL_FREQ    630   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define CHANNEL_DESC    710   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define RESERVE3        770   //Reserve3 between Channel and Firmware id check
 
 //Check Firmware type and version
 #define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
@@ -227,7 +242,7 @@ int count = 0;          //to generally count ticks, loops, etc
 char ritOn = 0;
 char vfoActive = VFO_A;
 int8_t meter_reading = 0; // a -1 on meter makes it invisible
-unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier;
+unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier, cwmCarrier;
 unsigned long vfoA_eeprom, vfoB_eeprom; //for protect eeprom life
 unsigned long frequency, ritRxFrequency, ritTxFrequency;  //frequency is the current frequency on the dial
 
@@ -244,7 +259,6 @@ byte saveIntervalSec = 10;  //second
 unsigned long saveCheckTime = 0;
 unsigned long saveCheckFreq = 0;
 
-bool isSplitOn = false;
 byte cwDelayTime = 60;
 byte delayBeforeCWStartTime = 50;
 
@@ -255,9 +269,12 @@ byte sideToneSub = 0;
 //DialLock
 byte isDialLock = 0;  //000000[0]vfoB [0]vfoA 0Bit : A, 1Bit : B
 byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
-byte arTuneStep[5];
+long arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
+byte displayOption1 = 0;
+byte displayOption2 = 0;
+
 //CW ADC Range
 int cwAdcSTFrom = 0;
 int cwAdcSTTo = 0;
@@ -267,6 +284,13 @@ int cwAdcDashFrom = 0;
 int cwAdcDashTo = 0;
 int cwAdcBothFrom = 0;
 int cwAdcBothTo = 0;
+byte cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+bool Iambic_Key = true;
+#define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
+unsigned char keyerControl = IAMBICB;
+
+byte isShiftDisplayCWFreq = 1;  //Display Frequency 
+int shiftDisplayAdjustVal = 0;  //
 
 //Variables for auto cw mode
 byte isCWAutoMode = 0;          //0 : none, 1 : CW_AutoMode_Menu_Selection, 2 : CW_AutoMode Sending
@@ -286,9 +310,13 @@ byte userCallsignLength = 0;    //7 : display callsign at system startup, 6~0 :
  */
 boolean txCAT = false;        //turned on if the transmitting due to a CAT command
 char inTx = 0;                //it is set to 1 if in transmit mode (whatever the reason : cw, ptt or cat)
-char splitOn = 0;             //working split, uses VFO B as the transmit frequency, (NOT IMPLEMENTED YET)
+char splitOn = 0;             //working split, uses VFO B as the transmit frequency
 char keyDown = 0;             //in cw mode, denotes the carrier is being transmitted
 char isUSB = 0;               //upper sideband was selected, this is reset to the default for the 
+
+char cwMode = 0;              //compatible original source, and extend mode //if cwMode == 0, mode check : isUSB, cwMode > 0, mode Check : cwMode
+                              //iscwMode = 0 : ssbmode, 1 :cwl, 2 : cwu, 3 : cwn (none tx)
+                              
                               //frequency when it crosses the frequency border of 10 MHz
 byte menuOn = 0;              //set to 1 when the menu is being displayed, if a menu item sets it to zero, the menu is exited
 unsigned long cwTimeout = 0;  //milliseconds to go before the cw transmit line is released and the radio goes back to rx mode
@@ -296,6 +324,14 @@ unsigned long dbgCount = 0;   //not used now
 unsigned char txFilter = 0;   //which of the four transmit filters are in use
 boolean modeCalibrate = false;//this mode of menus shows extended menus to calibrate the oscillators and choose the proper
                               //beat frequency
+
+unsigned long beforeIdle_ProcessTime = 0; //for check Idle time
+byte line2DisplayStatus = 0;  //0:Clear, 1 : menu, 1: DisplayFrom Idle, 
+char lcdMeter[17];
+
+byte isIFShift = 0;     //1 = ifShift, 2 extend
+long ifShiftValue = 0;  //
+                              
 /**
  * Below are the basic functions that control the uBitx. Understanding the functions before 
  * you start hacking around
@@ -348,29 +384,30 @@ void setNextHamBandFreq(unsigned long f, char moveDirection)
 
   EEPROM.get(HAM_BAND_FREQS + 4 * findedIndex, resultFreq);
   
-  loadMode = (byte)(resultFreq >> 30);
-  resultFreq = resultFreq & 0x3FFFFFFF;
+  //loadMode = (byte)(resultFreq >> 30);
+  //resultFreq = resultFreq & 0x3FFFFFFF;
+  loadMode = (byte)(resultFreq >> 29);
+  resultFreq = resultFreq & 0x1FFFFFFF;
   
   if ((resultFreq / 1000) < hamBandRange[(unsigned char)findedIndex][0] || (resultFreq / 1000) > hamBandRange[(unsigned char)findedIndex][1])
     resultFreq = (unsigned long)(hamBandRange[(unsigned char)findedIndex][0]) * 1000;
 
   setFrequency(resultFreq);
-  byteWithFreqToMode(loadMode);
+  byteToMode(loadMode, 1);
 }
 
 void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
   if (bandIndex >= 0)
-    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    //EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x1FFFFFFF) | (mode << 29) );
 }
 
-
 /*
   KD8CEC
   When using the basic delay of the Arduino, the program freezes.
   When the delay is used, the program will generate an error because it is not communicating, 
   so Create a new delay function that can do background processing.
  */
- 
 unsigned long delayBeforeTime = 0;
 byte delay_background(unsigned delayTime, byte fromType){ //fromType : 4 autoCWKey -> Check Paddle
   delayBeforeTime = millis();
@@ -457,13 +494,27 @@ void setFrequency(unsigned long f){
   
   setTXFilters(f);
 
-  if (isUSB){
-    si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_USB);
+  if (cwMode == 0)
+  {
+    if (isUSB){
+      si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f  + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
+    else{
+      si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
   }
-  else{
-    si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_LSB);
+  else
+  {
+    if (cwMode == 1){ //CWL
+      si5351bx_setfreq(2, SECOND_OSC_LSB + cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
+    else{             //CWU
+      si5351bx_setfreq(2, SECOND_OSC_USB - cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
   }
   
   frequency = f;
@@ -474,7 +525,6 @@ void setFrequency(unsigned long f){
  * put the uBitx in tx mode. It takes care of rit settings, sideband settings
  * Note: In cw mode, doesnt key the radio, only puts it in tx mode
  */
- 
 void startTx(byte txMode, byte isDisplayUpdate){
   //Check Hamband only TX //Not found Hamband index by now frequency
   if (tuneTXType >= 100 && getIndexHambanBbyFreq(ritOn ? ritTxFrequency :  frequency) == -1) {
@@ -492,6 +542,21 @@ void startTx(byte txMode, byte isDisplayUpdate){
     ritRxFrequency = frequency;
     setFrequency(ritTxFrequency);
   }
+  else if (splitOn == 1) {
+      if (vfoActive == VFO_B) {
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+
+      setFrequency(frequency);
+  } //end of else
+  
 
   if (txMode == TX_CW){
     //turn off the second local oscillator and the bfo
@@ -501,10 +566,22 @@ void startTx(byte txMode, byte isDisplayUpdate){
     //shif the first oscillator to the tx frequency directly
     //the key up and key down will toggle the carrier unbalancing
     //the exact cw frequency is the tuned frequency + sidetone
-    if (isUSB)
-      si5351bx_setfreq(2, frequency + sideTone);
-    else
-      si5351bx_setfreq(2, frequency - sideTone); 
+
+    if (cwMode == 0)
+    {
+      if (isUSB)
+        si5351bx_setfreq(2, frequency + sideTone);
+      else
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else if (cwMode == 1) //CWL
+    {
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else  //CWU
+    {
+        si5351bx_setfreq(2, frequency + sideTone);
+    }
   }
 
   //reduce latency time when begin of CW mode
@@ -516,10 +593,28 @@ void stopTx(){
   inTx = 0;
 
   digitalWrite(TX_RX, 0);           //turn off the tx
-  si5351bx_setfreq(0, usbCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
+  else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
 
   if (ritOn)
     setFrequency(ritRxFrequency);
+  else if (splitOn == 1) {
+      //vfo Change
+      if (vfoActive == VFO_B){
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+      setFrequency(frequency);
+  } //end of else
   else
     setFrequency(frequency);
   
@@ -585,7 +680,7 @@ void checkButton(){
     delay(10);
     Check_Cat(0);
   }
-  delay(50);//debounce
+  //delay(50);//debounce
 }
 
 
@@ -600,13 +695,12 @@ int encodedSumValue = 0;
 unsigned long lastTunetime = 0; //if continous moving, skip threshold processing
 byte lastMovedirection = 0; //0 : stop, 1 : cw, 2 : ccw
 
-#define skipThresholdTime 100
+//#define skipThresholdTime 70
 #define encodeTimeOut 1000
 
 void doTuningWithThresHold(){
   int s = 0;
   unsigned long prev_freq;
-  long incdecValue = 0;
 
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02)))
@@ -630,7 +724,9 @@ void doTuningWithThresHold(){
   encodedSumValue += (s > 0 ? 1 : -1);
 
   //check threshold and operator actions (hold dial speed = continous moving, skip threshold check)
-  if ((lastTunetime < millis() - skipThresholdTime) && ((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
+  //not use continues changing by Threshold
+  //if ((lastTunetime < (millis() - skipThresholdTime)) && ((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
+  if (((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
     return;
 
   lastTunetime = millis();
@@ -640,7 +736,8 @@ void doTuningWithThresHold(){
 
   prev_freq = frequency;
   //incdecValue = tuningStep * s;
-  frequency += (arTuneStep[tuneStepIndex -1] * s * (s * s < 10 ? 1 : 3));  //appield weight (s is speed)
+  //frequency += (arTuneStep[tuneStepIndex -1] * s * (s * s < 10 ? 1 : 3));  //appield weight (s is speed)
+  frequency += (arTuneStep[tuneStepIndex -1] * s);  //appield weight (s is speed) //if want need more increase size, change step size
     
   if (prev_freq < 10000000l && frequency > 10000000l)
     isUSB = true;
@@ -660,9 +757,9 @@ void doRIT(){
   unsigned long old_freq = frequency;
 
   if (knob < 0)
-    frequency -= 100l;
+    frequency -= (arTuneStep[tuneStepIndex -1]);  //
   else if (knob > 0)
-    frequency += 100;
+    frequency += (arTuneStep[tuneStepIndex -1]);  //
  
   if (old_freq != frequency){
     setFrequency(frequency);
@@ -670,8 +767,8 @@ void doRIT(){
   }
 }
 
-/**
- save Frequency and mode to eeprom
+/*
+ save Frequency and mode to eeprom for Auto Save with protected eeprom cycle, by kd8cec
  */
 void storeFrequencyAndMode(byte saveType)
 {
@@ -703,6 +800,22 @@ void storeFrequencyAndMode(byte saveType)
   }
 }
 
+//calculate step size from 1 byte, compatible uBITX Manager, by KD8CEC
+unsigned int byteToSteps(byte srcByte) {
+    byte powerVal = (byte)(srcByte >> 6);
+    unsigned int baseVal = srcByte & 0x3F;
+
+    if (powerVal == 1)
+        return baseVal * 10;
+    else if (powerVal == 2)
+        return baseVal * 100;
+    else if (powerVal == 3)
+        return baseVal * 1000;
+    else
+        return baseVal;
+}
+
+
 /**
  * The settings are read from EEPROM. The first time around, the values may not be 
  * present or out of range, in this case, some intelligent defaults are copied into the 
@@ -745,6 +858,7 @@ void initSettings(){
   if (EEPROM.read(VERSION_ADDRESS) != VERSION_NUM)
     EEPROM.write(VERSION_ADDRESS, VERSION_NUM);
 
+  EEPROM.get(CW_CAL, cwmCarrier);
 
   //for Save VFO_A_MODE to eeprom
   //0: default, 1:not use, 2:LSB, 3:USB, 4:CW, 5:AM, 6:FM
@@ -756,6 +870,24 @@ void initSettings(){
 
   //CW interval between TX and CW Start
   EEPROM.get(CW_START, delayBeforeCWStartTime);
+  EEPROM.get(CW_KEY_TYPE, cwKeyType);
+  if (cwKeyType > 2)
+    cwKeyType = 0;
+
+  if (cwKeyType == 0)
+    Iambic_Key = false;
+  else
+  {
+    Iambic_Key = true;
+    if (cwKeyType == 1)
+      keyerControl &= ~IAMBICB;
+    else
+      keyerControl |= IAMBICB;
+  }
+    
+
+  EEPROM.get(DISPLAY_OPTION1, displayOption1);
+  EEPROM.get(DISPLAY_OPTION2, displayOption2);
 
   //User callsign information
   if (EEPROM.read(USER_CALLSIGN_KEY) == 0x59)
@@ -784,13 +916,13 @@ void initSettings(){
   if ((3 < tuneTXType && tuneTXType < 100) || 103 < tuneTXType || useHamBandCount < 1 || findedValidValueCount < 5)
   {
     tuneTXType = 2;
-    //if empty band Information, auto insert default region 1 frequency range
+    //if empty band Information, auto insert default region 2 frequency range
     //This part is made temporary for people who have difficulty setting up, so can remove it when you run out of memory.
     useHamBandCount = 10;
     hamBandRange[0][0] = 1810; hamBandRange[0][1] = 2000; 
     hamBandRange[1][0] = 3500; hamBandRange[1][1] = 3800; 
     hamBandRange[2][0] = 5351; hamBandRange[2][1] = 5367; 
-    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7200; 
+    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;     //region 2
     hamBandRange[4][0] = 10100; hamBandRange[4][1] = 10150; 
     hamBandRange[5][0] = 14000; hamBandRange[5][1] = 14350; 
     hamBandRange[6][0] = 18068; hamBandRange[6][1] = 18168; 
@@ -804,8 +936,8 @@ void initSettings(){
   findedValidValueCount = 0;
   EEPROM.get(TUNING_STEP, tuneStepIndex);
   for (byte i = 0; i < 5; i++) {
-    arTuneStep[i] = EEPROM.read(TUNING_STEP + i + 1);
-    if (arTuneStep[i] >= 1 && arTuneStep[i] < 251) //Maximum 250 for check valid Value
+    arTuneStep[i] = byteToSteps(EEPROM.read(TUNING_STEP + i + 1));
+    if (arTuneStep[i] >= 1 && arTuneStep[i] <= 60000) //Maximum 650 for check valid Value
        findedValidValueCount++;
   }
 
@@ -838,6 +970,22 @@ void initSettings(){
   cwAdcBothFrom = EEPROM.read(CW_ADC_BOTH_FROM) | ((tmpMostBits & 0x30) << 4);
   cwAdcBothTo = EEPROM.read(CW_ADC_BOTH_TO)     | ((tmpMostBits & 0xC0) << 2);
 
+  //Display Type for CW mode
+  isShiftDisplayCWFreq = EEPROM.read(CW_DISPLAY_SHIFT);
+
+  //Adjust CW Mode Freq
+  shiftDisplayAdjustVal = (isShiftDisplayCWFreq & 0x3F) * 10;
+
+  //check Minus
+  if ((isShiftDisplayCWFreq & 0x40) == 0x40)
+    shiftDisplayAdjustVal = shiftDisplayAdjustVal * -1;
+
+ //Shift Display Check (Default : 0)
+  if ((isShiftDisplayCWFreq & 0x80) == 0)  //Enabled
+    isShiftDisplayCWFreq = 1;
+  else    //Disabled
+    isShiftDisplayCWFreq = 0;
+
   //default Value (for original hardware)
   if (cwAdcSTFrom >= cwAdcSTTo)
   {
@@ -875,15 +1023,18 @@ void initSettings(){
   //original code with modified by kd8cec
   if (usbCarrier > 12010000l || usbCarrier < 11990000l)
     usbCarrier = 11995000l;
+
+  if (cwmCarrier > 12010000l || cwmCarrier < 11990000l)
+    cwmCarrier = 11995000l;
     
   if (vfoA > 35000000l || 3500000l > vfoA) {
      vfoA = 7150000l;
-     vfoA_mode = 2;
+     vfoA_mode = 2; //LSB
   }
   
   if (vfoB > 35000000l || 3500000l > vfoB) {
      vfoB = 14150000l;  
-     vfoB_mode = 3;
+     vfoB_mode = 3; //USB
   }
   //end of original code section
 
@@ -909,7 +1060,6 @@ void initSettings(){
 }
 
 void initPorts(){
-
   analogReference(DEFAULT);
 
   //??
@@ -923,6 +1073,7 @@ void initPorts(){
 
   pinMode(PTT, INPUT_PULLUP);
   pinMode(ANALOG_KEYER, INPUT_PULLUP);
+  pinMode(ANALOG_SMETER, INPUT); //by KD8CEC
 
   pinMode(CW_TONE, OUTPUT);  
   digitalWrite(CW_TONE, 0);
@@ -958,7 +1109,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.30")); 
+  printLineF(1, F("CECBT v1.04")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -972,15 +1123,16 @@ void setup()
   else {
     printLineF(0, F("uBITX v0.20")); 
     delay(500);
-    printLine2(""); 
+    clearLine2();
   }
   
   initPorts();     
+
+  byteToMode(vfoA_mode, 0);
   initOscillators();
 
   frequency = vfoA;
   saveCheckFreq = frequency;  //for auto save frequency
-  byteToMode(vfoA_mode);
   setFrequency(vfoA);
   updateDisplay();
 
@@ -988,14 +1140,7 @@ void setup()
     factory_alignment();
 }
 
-
-/**
- * The loop checks for keydown, ptt, function button and tuning.
- */
-//for debug
-int dbgCnt = 0;
-byte flasher = 0;
-
+//Auto save Frequency and Mode with Protected eeprom life by KD8CEC
 void checkAutoSaveFreqMode()
 {
   //when tx or ritOn, disable auto save
@@ -1013,18 +1158,8 @@ void checkAutoSaveFreqMode()
     //check time for Frequency auto save
     if (millis() - saveCheckTime > saveIntervalSec * 1000)
     {
-      if (vfoActive == VFO_A)
-      {
-        vfoA = frequency;
-        vfoA_mode = modeToByte();
-        storeFrequencyAndMode(1);
-      }
-      else
-      {
-        vfoB = frequency;
-        vfoB_mode = modeToByte();
-        storeFrequencyAndMode(2);
-      }
+      FrequencyToVFO(1);
+      saveCheckTime = 0;  //for reduce cpu use rate
     }
   }
 }
@@ -1044,11 +1179,18 @@ void loop(){
   if (!inTx){
     if (ritOn)
       doRIT();
+    //else if (isIFShift)
+    //  doIFShift();
     else 
       doTuningWithThresHold();
-  }
+
+    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 250) {
+      idle_process();
+      checkAutoSaveFreqMode();  //move here form out scope for reduce cpu use rate
+      beforeIdle_ProcessTime = millis();
+    }
+  } //end of check TX Status
 
   //we check CAT after the encoder as it might put the radio into TX
   Check_Cat(inTx? 1 : 0);
-  checkAutoSaveFreqMode();
 }

ubitx_20/ubitx_factory_alignment.ino

@@ -14,6 +14,7 @@ void btnWaitForClick(){
 void factory_alignment(){
         
   factoryCalibration(1);
+  line2DisplayStatus = 1;
 
   if (calibration == 0){
     printLine2("Setup Aborted");
@@ -36,6 +37,7 @@ void factory_alignment(){
 
   
   printLine2("#3:Test 3.5MHz");
+  cwMode = 0;
   isUSB = false;
   setFrequency(3500000l);
   updateDisplay();
@@ -58,6 +60,7 @@ void factory_alignment(){
   btnWaitForClick();
   printLine2("#5:Test 14MHz");
 
+  cwMode = 0;
   isUSB = true;
   setFrequency(14000000l);
   updateDisplay();
@@ -79,6 +82,7 @@ void factory_alignment(){
   printLine2("Alignment done");
   delay(1000);
 
+  cwMode = 0;
   isUSB = false;
   setFrequency(7150000l);
   updateDisplay();  

ubitx_20/ubitx_idle.ino

@@ -0,0 +1,262 @@
+/*************************************************************************
+  KD8CEC's uBITX Idle time Processing
+  Functions that run at times that do not affect TX, CW, and CAT
+  It is called in 1/10 time unit.
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+**************************************************************************/
+char line2Buffer[16];
+//KD8CEC 200Hz ST
+//L14.150 200Hz ST
+//U14.150 +150khz
+int freqScrollPosition = 0;
+//Example Line2 Optinal Display
+//immediate execution, not call by scheulder
+void updateLine2Buffer(char isDirectCall)
+{
+  unsigned long tmpFreq = 0;
+  if (isDirectCall == 0)
+  {
+    if (ritOn)
+    {
+      strcpy(line2Buffer, "RitTX:");
+      /*
+      line2Buffer[0] = 'R';
+      line2Buffer[1] = 'i';
+      line2Buffer[2] = 't';
+      line2Buffer[3] = 'T';
+      line2Buffer[4] = 'X';
+      line2Buffer[5] = ':';
+      */
+  
+      //display frequency
+      tmpFreq = ritTxFrequency;
+      for (int i = 15; i >= 6; i--) {
+        if (tmpFreq > 0) {
+          if (i == 12 || i == 8) line2Buffer[i] = '.';
+          else {
+            line2Buffer[i] = tmpFreq % 10 + 0x30;
+            tmpFreq /= 10;
+          }
+        }
+        else
+          line2Buffer[i] = ' ';
+      }
+  
+      return;
+    } //end of ritOn display
+
+    //======================================================
+    //other VFO display
+    //======================================================
+    if (vfoActive == VFO_B)
+    {
+      tmpFreq = vfoA;
+    }
+    else 
+    {
+      tmpFreq = vfoB;
+    }
+  
+    // EXAMPLE 1 & 2
+    //U14.150.100
+    //display frequency
+    for (int i = 9; i >= 0; i--) {
+      if (tmpFreq > 0) {
+        if (i == 2 || i == 6) line2Buffer[i] = '.';
+        else {
+          line2Buffer[i] = tmpFreq % 10 + 0x30;
+          tmpFreq /= 10;
+        }
+      }
+      else
+        line2Buffer[i] = ' ';
+    }
+  
+    //EXAMPLE #1
+    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
+      line2Buffer[6] = 'k';
+    else
+    {
+      //example #2
+      if (freqScrollPosition++ > 18)    //none scroll display time
+      {
+        line2Buffer[6] = 'k';
+        if (freqScrollPosition > 25)
+          freqScrollPosition = -1;
+      }
+      else                              //scroll frequency 
+      {
+        line2Buffer[10] = 'H';
+        line2Buffer[11] = 'z';
+    
+        if (freqScrollPosition < 7)   
+        {
+          for (int i = 11; i >= 0; i--)
+            if (i - (7 - freqScrollPosition) >= 0)
+              line2Buffer[i] = line2Buffer[i - (7 - freqScrollPosition)];
+            else
+              line2Buffer[i] = ' ';
+        }
+        else
+        {
+          for (int i = 0; i < 11; i++)
+            if (i + (freqScrollPosition - 7) <= 11)
+              line2Buffer[i] = line2Buffer[i + (freqScrollPosition - 7)];
+            else
+              line2Buffer[i] = ' ';
+        }
+      }
+    } //scroll
+    
+    line2Buffer[7] = ' ';
+  } //check direct call by encoder
+  
+  if (isIFShift)
+  {
+    if (isDirectCall == 1)
+      for (int i = 0; i < 16; i++)
+        line2Buffer[i] = ' ';
+      
+      //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
+
+    //if (ifShiftValue == 0)
+    //{
+      /*
+      line2Buffer[10] = 'S';
+      line2Buffer[11] = ':';
+      line2Buffer[12] = 'O';
+      line2Buffer[13] = 'F';
+      line2Buffer[14] = 'F';
+      */
+    //}
+    //else
+    //{
+      line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+      line2Buffer[11] = 0;
+      line2Buffer[12] = ' ';
+    
+      //11, 12, 13, 14, 15
+      memset(b, 0, sizeof(b));
+      ltoa(ifShiftValue, b, DEC);
+      strncat(line2Buffer, b, 5);
+    //}
+    
+    if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
+        printLine2(line2Buffer);    
+  }       // end of display IF
+  else    // step display
+  {
+    if (isDirectCall != 0)
+      return;
+
+    memset(&line2Buffer[8], ' ', 8);
+    //Step
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
+      if (tmpStep > 0) {
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
+          tmpStep /= 10;
+      }
+      else
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+    //if (isStepKhz == 1)
+    //  line2Buffer[10] = 'k';
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[11] = 'H';
+      line2Buffer[12] = 'z';
+    }
+  
+    line2Buffer[13] = ' ';
+    //if (
+    //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+    if (cwKeyType == 0)
+    {
+      line2Buffer[14] = 'S';
+      line2Buffer[15] = 'T';
+    }
+    else if (cwKeyType == 1)
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'A';
+    }
+    else
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'B';
+    }    
+  }
+  
+}
+
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  if (meterType == 0 || meterType == 1 || meterType == 2)
+  {
+    drawMeter(meterValue);  //call original source code
+    int lineNumber = 0;
+    if ((displayOption1 & 0x01) == 0x01)
+      lineNumber = 1;
+    
+    lcd.setCursor(drawPosition, lineNumber);
+  
+    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+      lcd.write(lcdMeter[i]);
+  }
+}
+
+byte testValue = 0;
+char checkCount = 0;
+void idle_process()
+{
+  //space for user graphic display
+  if (menuOn == 0)
+  {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
+    //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
+    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
+        printLine2(line2Buffer);
+        line2DisplayStatus = 2;
+        checkCount = 0;
+      }
+
+      //EX for Meters
+      /*
+      DisplayMeter(0, testValue++, 7);
+      if (testValue > 30)
+        testValue = 0;
+      */
+    }
+  }
+}
+

ubitx_20/ubitx_keyer.ino

@@ -90,28 +90,26 @@ void cwKeyUp(){
 #define PDLSWAP 0x08 // 0 for normal, 1 for swap
 #define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
 enum KSTYPE {IDLE, CHK_DIT, CHK_DAH, KEYED_PREP, KEYED, INTER_ELEMENT };
-static long ktimer;
-bool Iambic_Key = true;
-unsigned char keyerControl = IAMBICB;
+static unsigned long ktimer;
 unsigned char keyerState = IDLE;
 
 //Below is a test to reduce the keying error. do not delete lines
 //create by KD8CEC for compatible with new CW Logic
 char update_PaddleLatch(byte isUpdateKeyState) {
-  unsigned char tmpKeyerControl;
+  unsigned char tmpKeyerControl = 0;
   int paddle = analogRead(ANALOG_KEYER);
 
-  if (paddle > cwAdcDashFrom && paddle < cwAdcDashTo)
+  if (paddle >= cwAdcDashFrom && paddle <= cwAdcDashTo)
     tmpKeyerControl |= DAH_L;
-  else if (paddle > cwAdcDotFrom && paddle < cwAdcDotTo)
+  else if (paddle >= cwAdcDotFrom && paddle <= cwAdcDotTo)
     tmpKeyerControl |= DIT_L;
-  else if (paddle > cwAdcBothFrom && paddle < cwAdcBothTo)
+  else if (paddle >= cwAdcBothFrom && paddle <= cwAdcBothTo)
     tmpKeyerControl |= (DAH_L | DIT_L) ;     
   else 
   {
     if (Iambic_Key)
       tmpKeyerControl = 0 ;
-    else if (paddle > cwAdcSTFrom && paddle < cwAdcSTTo)
+    else if (paddle >= cwAdcSTFrom && paddle <= cwAdcSTTo)
       tmpKeyerControl = DIT_L ;
      else
        tmpKeyerControl = 0 ; 
@@ -128,9 +126,7 @@ char update_PaddleLatch(byte isUpdateKeyState) {
 // modified by KD8CEC
 ******************************************************************************/
 void cwKeyer(void){
-  byte paddle;
   lastPaddle = 0;
-  int dot,dash;
   bool continue_loop = true;
   unsigned tmpKeyControl = 0;
   
@@ -176,6 +172,9 @@ void cwKeyer(void){
           keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
           keyerState = KEYED; // next state
           if (!inTx){
+            //DelayTime Option
+            delay_background(delayBeforeCWStartTime * 2, 2);
+            
             keyDown = 0;
             cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
             startTx(TX_CW, 1);
@@ -208,7 +207,7 @@ void cwKeyer(void){
           break;
       }
   
-      Check_Cat(3);
+      Check_Cat(2);
     } //end of while
   }
   else{
@@ -216,6 +215,9 @@ void cwKeyer(void){
       if (update_PaddleLatch(0) == DIT_L) {
         // if we are here, it is only because the key is pressed
         if (!inTx){
+          //DelayTime Option
+          delay_background(delayBeforeCWStartTime * 2, 2);
+          
           keyDown = 0;
           cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT; 
           startTx(TX_CW, 1);
@@ -233,13 +235,14 @@ void cwKeyer(void){
           keyDown = 0;
           stopTx();
         }
-        if (!cwTimeout)
-          return;
+        //if (!cwTimeout) //removed by KD8CEC
+        //   return;
         // got back to the beginning of the loop, if no further activity happens on straight key
         // we will time out, and return out of this routine 
         //delay(5);
-        delay_background(5, 3);
-        continue;
+        //delay_background(5, 3); //removed by KD8CEC
+        //continue;               //removed by KD8CEC
+        return;                   //Tx stop control by Main Loop
       }
 
       Check_Cat(2);

ubitx_20/ubitx_si5351.ino

@@ -60,6 +60,7 @@ void i2cWriten(uint8_t reg, uint8_t *vals, uint8_t vcnt) {  // write array
   Wire.endTransmission();
 }
 
+uint8_t  si5351Val[8] = {0, 1, 0, 0, 0, 0, 0, 0}; //for reduce program memory size
 
 void si5351bx_init() {                  // Call once at power-up, start PLLA
   uint32_t msxp1;
@@ -68,11 +69,13 @@ void si5351bx_init() {                  // Call once at power-up, start PLLA
   i2cWrite(3, si5351bx_clken);          // Disable all CLK output drivers
   i2cWrite(183, SI5351BX_XTALPF << 6);  // Set 25mhz crystal load capacitance
   msxp1 = 128 * SI5351BX_MSA - 512;     // and msxp2=0, msxp3=1, not fractional
-  uint8_t  vals[8] = {0, 1, BB2(msxp1), BB1(msxp1), BB0(msxp1), 0, 0, 0};
-  i2cWriten(26, vals, 8);               // Write to 8 PLLA msynth regs
+  //uint8_t  vals[8] = {0, 1, BB2(msxp1), BB1(msxp1), BB0(msxp1), 0, 0, 0};
+  si5351Val[2] = BB2(msxp1);
+  si5351Val[3] = BB1(msxp1);
+  si5351Val[4] = BB0(msxp1);
+  
+  i2cWriten(26, si5351Val, 8);               // Write to 8 PLLA msynth regs
   i2cWrite(177, 0x20);                  // Reset PLLA  (0x80 resets PLLB)
-  // for (reg=16; reg<=23; reg++) i2cWrite(reg, 0x80);    // Powerdown CLK's
-  // i2cWrite(187, 0);                  // No fannout of clkin, xtal, ms0, ms4
 }
 
 void si5351bx_setfreq(uint8_t clknum, uint32_t fout) {  // Set a CLK to fout Hz
@@ -109,7 +112,11 @@ void initOscillators(){
   //initialize the SI5351
   si5351bx_init();
   si5351bx_vcoa = (SI5351BX_XTAL * SI5351BX_MSA) + calibration; // apply the calibration correction factor
-  si5351bx_setfreq(0, usbCarrier);
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));
+ else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));
 }
 
 

ubitx_20/ubitx_ui.ino

@@ -25,8 +25,8 @@ int btnDown(){
  * The current reading of the meter is assembled in the string called meter
  */
 
-//char meter[17];
 
+/*
 const PROGMEM uint8_t s_meter_bitmap[] = {
   B00000,B00000,B00000,B00000,B00000,B00100,B00100,B11011,
   B10000,B10000,B10000,B10000,B10100,B10100,B10100,B11011,
@@ -35,7 +35,18 @@ const PROGMEM uint8_t s_meter_bitmap[] = {
   B00010,B00010,B00010,B00010,B00110,B00110,B00110,B11011,
   B00001,B00001,B00001,B00001,B00101,B00101,B00101,B11011
 };
-PGM_P ps_meter_bitmap = reinterpret_cast<PGM_P>(s_meter_bitmap);
+*/
+
+const PROGMEM uint8_t meters_bitmap[] = {
+  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000 ,   //custom 1
+  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000 ,   //custom 2
+  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100 ,   //custom 3
+  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110 ,   //custom 4
+  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111 ,   //custom 5
+  B01000,  B11100,  B01000,  B00000,  B10111,  B10101,  B10101,  B10111     //custom 6
+};
+
+PGM_P p_metes_bitmap = reinterpret_cast<PGM_P>(meters_bitmap);
 
 const PROGMEM uint8_t lock_bitmap[8] = {
   0b01110,
@@ -60,38 +71,54 @@ void initMeter(){
   lcd.createChar(0, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i);
   lcd.createChar(1, tmpbytes);
 
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 8);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 8);
   lcd.createChar(2, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 16);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 16);
   lcd.createChar(3, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 24);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 24);
   lcd.createChar(4, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 28);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 32);
   lcd.createChar(5, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 32);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 40);
   lcd.createChar(6, tmpbytes);
 }
 
-/**
- * The meter is drawn with special characters.
- * character 1 is used to simple draw the blocks of the scale of the meter
- * characters 2 to 6 are used to draw the needle in positions 1 to within the block
- * This displays a meter from 0 to 100, -1 displays nothing
- */
+//by KD8CEC
+//0 ~ 25 : 30 over : + 10
+void drawMeter(int needle) {
+  //5Char + O over
+  int i;
 
- /*
+  for (i = 0; i < 5; i++) {
+    if (needle >= 5)
+      lcdMeter[i] = 5; //full
+    else if (needle > 0)
+      lcdMeter[i] = needle; //full
+    else  //0
+      lcdMeter[i] = 0x20;
+    
+    needle -= 5;
+  }
+
+  if (needle > 0)
+    lcdMeter[5] = 6;
+  else
+    lcdMeter[5] = 0x20;
+}
+
+/*
 void drawMeter(int8_t needle){
   int16_t best, i, s;
 
@@ -101,21 +128,23 @@ void drawMeter(int8_t needle){
   s = (needle * 4)/10;
   for (i = 0; i < 8; i++){
     if (s >= 5)
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     else if (s >= 0)
-      meter[i] = 2 + s;
+      lcdMeter[i] = 2 + s;
     else
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     s = s - 5;
   }
   if (needle >= 40)
-    meter[i-1] = 6;
-  meter[i] = 0;
+    lcdMeter[i-1] = 6;
+  lcdMeter[i] = 0;
 }
 */
-
 // The generic routine to display one line on the LCD 
 void printLine(unsigned char linenmbr, const char *c) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+    
   if (strcmp(c, printBuff[linenmbr])) {     // only refresh the display when there was a change
     lcd.setCursor(0, linenmbr);             // place the cursor at the beginning of the selected line
     lcd.print(c);
@@ -145,6 +174,9 @@ void printLineF(char linenmbr, const __FlashStringHelper *c)
 
 #define LCD_MAX_COLUMN 16
 void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  
   lcd.setCursor(lcdColumn, linenmbr);
 
   for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
@@ -168,6 +200,12 @@ void printLine2(const char *c){
   printLine(0,c);
 }
 
+void clearLine2()
+{
+  printLine2("");
+  line2DisplayStatus = 0;
+}
+
 //  short cut to print to the first line
 void printLine1Clear(){
   printLine(1,"");
@@ -179,6 +217,7 @@ void printLine2Clear(){
 
 void printLine2ClearAndUpdate(){
   printLine(0, "");
+  line2DisplayStatus = 0;  
   updateDisplay();
 }
 
@@ -194,7 +233,6 @@ char byteToChar(byte srcByte){
 void updateDisplay() {
   // tks Jack Purdum W8TEE
   // replaced fsprint commmands by str commands for code size reduction
-  
   // replace code for Frequency numbering error (alignment, point...) by KD8CEC
   int i;
   unsigned long tmpFreq = frequency; //
@@ -221,10 +259,21 @@ void updateDisplay() {
     if (ritOn)
       strcpy(c, "RIT ");
     else {
-      if (isUSB)
-        strcpy(c, "USB ");
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          strcpy(c, "USB ");
+        else
+          strcpy(c, "LSB ");
+      }
+      else if (cwMode == 1)
+      {
+          strcpy(c, "CWL ");
+      }
       else
-        strcpy(c, "LSB ");
+      {
+          strcpy(c, "CWU ");
+      }
     }
     if (vfoActive == VFO_A) // VFO A is active
       strcat(c, "A:");
@@ -232,6 +281,15 @@ void updateDisplay() {
       strcat(c, "B:");
   }
 
+  //Fixed by Mitani Massaru (JE4SMQ)
+  if (isShiftDisplayCWFreq == 1)
+  {
+    if (cwMode == 1)        //CWL
+        tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+    else if (cwMode == 2)   //CWU
+        tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+  }
+
   //display frequency
   for (int i = 15; i >= 6; i--) {
     if (tmpFreq > 0) {
@@ -251,36 +309,24 @@ void updateDisplay() {
   //  strcat(c, " TX");
   printLine(1, c);
 
+  byte diplayVFOLine = 1;
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayVFOLine = 0;
+
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02))) {
-    lcd.setCursor(5,1);
+    lcd.setCursor(5,diplayVFOLine);
     lcd.write((uint8_t)0);
   }
   else if (isCWAutoMode == 2){
-    lcd.setCursor(5,1);
+    lcd.setCursor(5,diplayVFOLine);
     lcd.write(0x7E);
   }
   else
   {
-    lcd.setCursor(5,1);
+    lcd.setCursor(5,diplayVFOLine);
     lcd.write(":");
   }
-
-/*
-  //now, the second line
-  memset(c, 0, sizeof(c));
-  memset(b, 0, sizeof(b));
-
-  if (inTx)
-    strcat(c, "TX ");
-  else if (ritOn)
-    strcpy(c, "RIT");
-
-  strcpy(c, "      \xff");
-  drawMeter(meter_reading);
-  strcat(c, meter);
-  strcat(c, "\xff");
-  printLine2(c);*/
 }
 
 int enc_prev_state = 3;