change channel name display code

ubitx_20/cw_autokey.ino

@@ -365,6 +365,11 @@ void controlAutoCW(){
         //check interval time, if you want adjust interval between chars, modify below
         if (isAutoCWHold == 0 && (millis() - autoCWbeforeTime > cwSpeed * 3))
         {
+          if (!inTx){                                           //if not TX Status, change RX -> TX
+            keyDown = 0;
+            startTx(TX_CW, 0);  //disable updateDisplay Command for reduce latency time
+          }
+          
           sendCWChar(EEPROM.read(CW_AUTO_DATA + autoCWSendCharIndex++));
 
           if (autoCWSendCharIndex > autoCWSendCharEndIndex) {          //finish auto cw send

ubitx_20/ubitx_20.ino

@@ -160,7 +160,8 @@ int count = 0;          //to generally count ticks, loops, etc
 #define TX_TUNE_TYPE 261  //
 #define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
 #define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)
+#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+  
 
 //for reduce cw key error, eeprom address
 #define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
@@ -179,6 +180,10 @@ int count = 0;          //to generally count ticks, loops, etc
 #define DISPLAY_OPTION1  361   //Display Option1
 #define DISPLAY_OPTION2  362   //Display Option2
 
+#define CHANNEL_FREQ    630   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define CHANNEL_DESC    710   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define RESERVE3        770   //Reserve3 between Channel and Firmware id check
+
 //Check Firmware type and version
 #define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
 #define VERSION_ADDRESS 779   //check Firmware version
@@ -260,7 +265,7 @@ byte sideToneSub = 0;
 //DialLock
 byte isDialLock = 0;  //000000[0]vfoB [0]vfoA 0Bit : A, 1Bit : B
 byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
-byte arTuneStep[5];
+long arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
 byte displayOption1 = 0;
@@ -381,7 +386,7 @@ void setNextHamBandFreq(unsigned long f, char moveDirection)
     resultFreq = (unsigned long)(hamBandRange[(unsigned char)findedIndex][0]) * 1000;
 
   setFrequency(resultFreq);
-  byteWithFreqToMode(loadMode);
+  byteToMode(loadMode, 1);
 }
 
 void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
@@ -536,12 +541,12 @@ void startTx(byte txMode, byte isDisplayUpdate){
       if (vfoActive == VFO_B) {
         vfoActive = VFO_A;
         frequency = vfoA;
-        byteToMode(vfoA_mode);
+        byteToMode(vfoA_mode, 0);
       }
       else if (vfoActive == VFO_A){
         vfoActive = VFO_B;
         frequency = vfoB;
-        byteToMode(vfoB_mode);
+        byteToMode(vfoB_mode, 0);
       }
 
       setFrequency(frequency);
@@ -596,12 +601,12 @@ void stopTx(){
       if (vfoActive == VFO_B){
         vfoActive = VFO_A;
         frequency = vfoA;
-        byteToMode(vfoA_mode);
+        byteToMode(vfoA_mode, 0);
       }
       else if (vfoActive == VFO_A){
         vfoActive = VFO_B;
         frequency = vfoB;
-        byteToMode(vfoB_mode);
+        byteToMode(vfoB_mode, 0);
       }
       setFrequency(frequency);
   } //end of else
@@ -754,27 +759,8 @@ void doRIT(){
     updateDisplay();
   }
 }
-
 /*
-void doIFShift(){
-  int knob = enc_read();
-  unsigned long old_freq = frequency;
-
-  if (knob != 0)
-  {
-    if (knob < 0)
-      ifShiftValue -= 1l;
-    else if (knob > 0)
-      ifShiftValue += 1;
-
-    updateLine2Buffer(1);
-    setFrequency(frequency);
-  }
-}
-*/
-
-/**
- save Frequency and mode to eeprom
+ save Frequency and mode to eeprom for Auto Save with protected eeprom cycle, by kd8cec
  */
 void storeFrequencyAndMode(byte saveType)
 {
@@ -806,6 +792,22 @@ void storeFrequencyAndMode(byte saveType)
   }
 }
 
+//calculate step size from 1 byte, compatible uBITX Manager, by KD8CEC
+unsigned int byteToSteps(byte srcByte) {
+    byte powerVal = (byte)(srcByte >> 6);
+    unsigned int baseVal = srcByte & 0x3F;
+
+    if (powerVal == 1)
+        return baseVal * 10;
+    else if (powerVal == 2)
+        return baseVal * 100;
+    else if (powerVal == 3)
+        return baseVal * 1000;
+    else
+        return baseVal;
+}
+
+
 /**
  * The settings are read from EEPROM. The first time around, the values may not be 
  * present or out of range, in this case, some intelligent defaults are copied into the 
@@ -926,8 +928,8 @@ void initSettings(){
   findedValidValueCount = 0;
   EEPROM.get(TUNING_STEP, tuneStepIndex);
   for (byte i = 0; i < 5; i++) {
-    arTuneStep[i] = EEPROM.read(TUNING_STEP + i + 1);
-    if (arTuneStep[i] >= 1 && arTuneStep[i] < 251) //Maximum 250 for check valid Value
+    arTuneStep[i] = byteToSteps(EEPROM.read(TUNING_STEP + i + 1));
+    if (arTuneStep[i] >= 1 && arTuneStep[i] <= 60000) //Maximum 650 for check valid Value
        findedValidValueCount++;
   }
 
@@ -1003,12 +1005,12 @@ void initSettings(){
     
   if (vfoA > 35000000l || 3500000l > vfoA) {
      vfoA = 7150000l;
-     vfoA_mode = 2;
+     vfoA_mode = 2; //LSB
   }
   
   if (vfoB > 35000000l || 3500000l > vfoB) {
      vfoB = 14150000l;  
-     vfoB_mode = 3;
+     vfoB_mode = 3; //USB
   }
   //end of original code section
 
@@ -1084,7 +1086,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.33")); 
+  printLineF(1, F("CECBT v0.35")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -1103,7 +1105,7 @@ void setup()
   
   initPorts();     
 
-  byteToMode(vfoA_mode);
+  byteToMode(vfoA_mode, 0);
   initOscillators();
 
   frequency = vfoA;
@@ -1116,13 +1118,11 @@ void setup()
 }
 
 
-/**
- * The loop checks for keydown, ptt, function button and tuning.
- */
 //for debug
 int dbgCnt = 0;
 byte flasher = 0;
 
+//Auto save Frequency and Mode with Protected eeprom life by KD8CEC
 void checkAutoSaveFreqMode()
 {
   //when tx or ritOn, disable auto save

ubitx_20/ubitx_idle.ino

@@ -17,7 +17,7 @@
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 **************************************************************************/
-byte line2Buffer[16];
+char line2Buffer[16];
 //KD8CEC 200Hz ST
 //L14.150 200Hz ST
 //U14.150 +150khz
@@ -53,8 +53,11 @@ void updateLine2Buffer(char isDirectCall)
       }
   
       return;
-    }
-    
+    } //end of ritOn display
+
+    //======================================================
+    //other VFO display
+    //======================================================
     if (vfoActive == VFO_B)
     {
       tmpFreq = vfoA;
@@ -82,23 +85,23 @@ void updateLine2Buffer(char isDirectCall)
     }
   
     //EXAMPLE #1
-    if ((displayOption1 & 0x04) == 0x00)
+    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
       line2Buffer[6] = 'k';
     else
     {
       //example #2
-      if (freqScrollPosition++ > 18)
+      if (freqScrollPosition++ > 18)    //none scroll display time
       {
         line2Buffer[6] = 'k';
         if (freqScrollPosition > 25)
           freqScrollPosition = -1;
       }
-      else
+      else                              //scroll frequency 
       {
         line2Buffer[10] = 'H';
         line2Buffer[11] = 'z';
     
-        if (freqScrollPosition < 7)
+        if (freqScrollPosition < 7)   
         {
           for (int i = 11; i >= 0; i--)
             if (i - (7 - freqScrollPosition) >= 0)
@@ -115,10 +118,10 @@ void updateLine2Buffer(char isDirectCall)
               line2Buffer[i] = ' ';
         }
       }
-    }
+    } //scroll
+    
     line2Buffer[7] = ' ';
   } //check direct call by encoder
-
   
   if (isIFShift)
   {
@@ -152,24 +155,38 @@ void updateLine2Buffer(char isDirectCall)
     
     if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
         printLine2(line2Buffer);    
-  }
-  else
+  }       // end of display IF
+  else    // step display
   {
     if (isDirectCall != 0)
       return;
-      
+
+    memset(&line2Buffer[8], ' ', 8);
     //Step
-    byte tmpStep = arTuneStep[tuneStepIndex -1];
-    for (int i = 10; i >= 8; i--) {
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
       if (tmpStep > 0) {
-          line2Buffer[i] = tmpStep % 10 + 0x30;
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
           tmpStep /= 10;
       }
       else
-        line2Buffer[i] = ' ';
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+    //if (isStepKhz == 1)
+    //  line2Buffer[10] = 'k';
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[11] = 'H';
+      line2Buffer[12] = 'z';
     }
-    line2Buffer[11] = 'H';
-    line2Buffer[12] = 'z';
   
     line2Buffer[13] = ' ';
     //if (
@@ -215,6 +232,9 @@ void idle_process()
   //space for user graphic display
   if (menuOn == 0)
   {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
     //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
     if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
       if (checkCount++ > 1)

ubitx_20/ubitx_menu.ino

@@ -13,7 +13,39 @@
 #define printLineF1(x) (printLineF(1, x))
 #define printLineF2(x) (printLineF(0, x))
 
-//Ham band move by KD8CEC
+//Current Frequency and mode to active VFO by KD8CEC
+void FrequencyToVFO(byte isSaveFreq)
+{
+  //Save Frequency & Mode Information
+  if (vfoActive == VFO_A)
+  {
+    vfoA = frequency;
+    vfoA_mode = modeToByte();
+
+    if (isSaveFreq)
+      storeFrequencyAndMode(1);
+  }
+  else
+  {
+    vfoB = frequency;
+    vfoB_mode = modeToByte();
+    
+    if (isSaveFreq)
+      storeFrequencyAndMode(2);
+  }
+}
+
+//Commonly called functions when exiting menus by KD8CEC
+void menuClearExit(int delayTime)
+{
+  if (delayTime > 0)
+    delay_background(delayTime, 0);
+    
+  printLine2ClearAndUpdate();
+  menuOn = 0;
+}
+
+//Ham band or general band movement by KD8CEC
 void menuBand(int btn){
   int knob = 0;
   int stepChangeCount = 0;
@@ -27,8 +59,7 @@ void menuBand(int btn){
   printLineF2(F("Press to confirm"));
   //wait for the button menu select button to be lifted)
   while (btnDown()) {
-    delay(50);
-    Check_Cat(0);  //To prevent disconnections
+     delay_background(50, 0);
     if (btnPressCount++ > 20) {
       btnPressCount = 0;
       if (tuneTXType > 0) { //Just toggle 0 <-> 2, if tuneTXType is 100, 100 -> 0 -> 2
@@ -57,23 +88,13 @@ void menuBand(int btn){
     }
   }
   
-  delay(50);    
+  //delay(50);    
   ritDisable();
 
   while(!btnDown()){
 
     knob = enc_read();
     if (knob != 0){
-      /*
-      if (band > 3 && knob < 0)
-        band--;
-      if (band < 30 && knob > 0)
-        band++; 
-      if (band > 10)
-        isUSB = true;
-      else
-        isUSB = false;
-      setFrequency(((unsigned long)band * 1000000l) + offset); */
       if (tuneTXType == 2 || tuneTXType == 3 || tuneTXType == 102 || tuneTXType == 103) { //only ham band move
         if (knob < 0) {
           if (stepChangeCount-- < -3) {
@@ -87,9 +108,7 @@ void menuBand(int btn){
             stepChangeCount = 0;
           }
         }
-
-      //setFrequency(frequency + 200000l);
-      }
+      }       //end of only ham band move
       else {  //original source
         if (knob < 0 && frequency > 3000000l)
           setFrequency(frequency - 200000l);
@@ -105,19 +124,21 @@ void menuBand(int btn){
       updateDisplay();
     }
     
-    delay(20);
-    Check_Cat(0);  //To prevent disconnections
+    delay_background(20, 0);
   }
 
+/*
   while(btnDown()) {
     delay(50);
     Check_Cat(0);  //To prevent disconnections
   }
-  
-  delay(50);
-  
-  printLine2ClearAndUpdate();
-  menuOn = 0;
+*/  
+  FrequencyToVFO(1);
+
+  //printLine2ClearAndUpdate();
+  //delay_background(500, 0);
+  //menuOn = 0;
+  menuClearExit(500);
 }
 
 //Convert Mode, Number by KD8CEC
@@ -141,7 +162,9 @@ byte modeToByte(){
 }
 
 //Convert Number to Mode by KD8CEC
-void byteToMode(byte modeValue){
+//autoSetModebyFreq : 0
+//autoSetModebyFreq : 1, if (modValue is not set, set mode by frequency)
+void byteToMode(byte modeValue, byte autoSetModebyFreq){
   if (modeValue == 4)
     cwMode = 1;
   else if (modeValue == 5)
@@ -151,11 +174,14 @@ void byteToMode(byte modeValue){
     cwMode = 0;
     if (modeValue == 3)
       isUSB = 1;
+    else if (autoSetModebyFreq == 1 && (modeValue == 0))
+      isUSB = (frequency > 10000000l) ? true : false;
     else
       isUSB = 0;
   }
 }
 
+/*
 //Convert Number to Mode by KD8CEC
 void byteWithFreqToMode(byte modeValue){
   if (modeValue == 4)
@@ -172,99 +198,10 @@ void byteWithFreqToMode(byte modeValue){
       isUSB = 0;
   }
 }
-
-//VFO Toggle and save VFO Information, modified by KD8CEC
-void menuVfoToggle(int btn, char isUseDelayTime)
-{
-  if (!btn){
-    if (vfoActive == VFO_A)
-      printLineF2(F("Select VFO B?"));
-    else
-      printLineF2(F("Select VFO A?"));    
-  }
-  else {
-      if (vfoActive == VFO_B){
-        vfoB = frequency;
-        vfoB_mode = modeToByte();
-        storeFrequencyAndMode(2); //vfoB -> eeprom
-        
-        vfoActive = VFO_A;
-        frequency = vfoA;
-        saveCheckFreq = frequency;
-        byteToMode(vfoA_mode);
-        printLineF2(F("Selected VFO A"));
-      }
-      else {
-        vfoA = frequency;
-        vfoA_mode = modeToByte();
-        storeFrequencyAndMode(1); //vfoA -> eeprom
-        
-        vfoActive = VFO_B;
-        frequency = vfoB;
-        saveCheckFreq = frequency;
-        byteToMode(vfoB_mode);
-        printLineF2(F("Selected VFO B"));
-      }
-
-      ritDisable();
-      setFrequency(frequency);
-
-      if (isUseDelayTime == 1)        //Found Issue in wsjt-x Linux 32bit 
-        delay_background(500, 0);
-
-      printLine2ClearAndUpdate();
-      //exit the menu
-      menuOn = 0;
-  }
-}
-
-void menuRitToggle(int btn){
-  if (!btn){
-    if (ritOn == 1)
-      printLineF2(F("RIT:On, Off?"));
-    else
-      printLineF2(F("RIT:Off, On?"));
-  }
-  else {
-      if (ritOn == 0){
-        printLineF2(F("RIT is ON"));
-        //enable RIT so the current frequency is used at transmit
-        ritEnable(frequency);
-      }
-      else{
-        printLineF2(F("RIT is OFF"));
-        ritDisable();
-      }
-      menuOn = 0;
-      delay_background(500, 0);
-      printLine2ClearAndUpdate();
-  }
-}
-
-/*
-void menuIFSToggle(int btn){
-  if (!btn){
-    if (isIFShift == 1)
-      printLineF2(F("IF Shift:On, Off?"));
-    else
-      printLineF2(F("IF Shift:Off, On?"));
-  }
-  else {
-      if (isIFShift == 0){
-        printLineF2(F("IF Shift is ON"));
-        isIFShift = 1;
-      }
-      else{
-        printLineF2(F("IF Shift is OFF"));
-        isIFShift = 0;
-      }
-      menuOn = 0;
-      delay_background(500, 0);
-      printLine2ClearAndUpdate();
-  }
-}
 */
-void menuIFSToggle(int btn){
+
+//IF Shift function, BFO Change like RIT, by KD8CEC
+void menuIFSSetup(int btn){
   int knob = 0;
   char needApplyChangeValue = 1;
   
@@ -275,18 +212,18 @@ void menuIFSToggle(int btn){
       printLineF2(F("IF Shift:Off, On?"));
   }
   else {
-      if (isIFShift == 0){
-        printLineF2(F("IF Shift is ON"));
-        delay_background(500, 0);
-        isIFShift = 1;
-      }
+      //if (isIFShift == 0){
+        //printLineF2(F("IF Shift is ON"));
+        //delay_background(500, 0);
+      isIFShift = 1;
+      //}
 
       delay_background(500, 0);
       updateLine2Buffer(1);
       setFrequency(frequency);
 
       //Off or Change Value
-      while(!btnDown() && digitalRead(PTT) == HIGH){
+      while(!btnDown() ){
         if (needApplyChangeValue ==1)
         {
           updateLine2Buffer(1);
@@ -303,9 +240,9 @@ void menuIFSToggle(int btn){
         knob = enc_read();
         if (knob != 0){
           if (knob < 0)
-            ifShiftValue -= 1l;
+            ifShiftValue -= 50l;
           else if (knob > 0)
-            ifShiftValue += 1;
+            ifShiftValue += 50;
 
           needApplyChangeValue = 1;
         }
@@ -313,7 +250,7 @@ void menuIFSToggle(int btn){
 
       delay_background(500, 0); //for check Long Press function key
       
-      if (btnDown() || digitalRead(PTT) == LOW || ifShiftValue == 0)
+      if (btnDown() || ifShiftValue == 0)
       {
         isIFShift = 0;
         printLineF2(F("IF Shift is OFF"));
@@ -321,38 +258,13 @@ void menuIFSToggle(int btn){
         delay_background(500, 0);
       }
       
-      menuOn = 0;
-      //delay_background(500, 0);
-      printLine2ClearAndUpdate();
+      //menuOn = 0;
+      //printLine2ClearAndUpdate();
+      menuClearExit(0);
   }
 }
 
-
-/* 
-void menuSidebandToggle(int btn){
-  if (!btn){
-    if (isUSB == true)
-      printLineF2(F("Select LSB?"));
-    else
-      printLineF2(F("Select USB?"));
-  }
-  else {
-      cwMode = 0;
-      if (isUSB == true){
-        isUSB = false;
-        printLineF2(F("LSB Selected"));
-      }
-      else {
-        isUSB = true;
-        printLineF2(F("USB Selected"));
-      }
-    setFrequency(frequency);
-    delay_background(500, 0);
-    printLine2ClearAndUpdate();
-    menuOn = 0;
-  }
-}
-*/
+//Functions for CWL and CWU by KD8CEC
 void menuSelectMode(int btn){
   int knob = 0;
   int selectModeType = 0;
@@ -412,8 +324,7 @@ void menuSelectMode(int btn){
     }
 
     if (beforeMode != selectModeType) {
-      printLineF1(F("Changed Mode"));
-      
+      //printLineF1(F("Changed Mode"));
       if (selectModeType == 0) {
         cwMode = 0; isUSB = 0;
       }
@@ -427,19 +338,7 @@ void menuSelectMode(int btn){
         cwMode = 2;
       }
 
-      //Save Frequency & Mode Information
-      if (vfoActive == VFO_A)
-      {
-        vfoA = frequency;
-        vfoA_mode = modeToByte();
-        storeFrequencyAndMode(1);
-      }
-      else
-      {
-        vfoB = frequency;
-        vfoB_mode = modeToByte();
-        storeFrequencyAndMode(2);
-      }
+      FrequencyToVFO(1);
     }
 
   if (cwMode == 0)
@@ -448,72 +347,140 @@ void menuSelectMode(int btn){
     si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
     
     setFrequency(frequency);
-    delay_background(500, 0);
-    printLine2ClearAndUpdate();
-    menuOn = 0;
+
+    //delay_background(500, 0);
+    //printLine2ClearAndUpdate();
+    //menuOn = 0;
+    menuClearExit(500);
   }
 }
 
-void menuSplitOnOff(int btn){
+
+//Memory to VFO, VFO to Memory by KD8CEC
+//select between MtoV and VtoM by isMemoryToVfo
+void menuCHMemory(int btn, byte isMemoryToVfo){
+  int knob = 0;
+  int selectChannel = 0;
+  byte isDisplayInfo = 1;
+  byte isCancel = 0;
+  int moveStep = 0;
+  unsigned long resultFreq, tmpFreq = 0;
+  byte loadMode = 0;
+  
   if (!btn){
-    if (splitOn == 0)
-      printLineF2(F("Split On?"));
-    else
-      printLineF2(F("Split Off?"));
+    if (isMemoryToVfo == 1)
+      printLine2("Channel To VFO?");
+   else 
+      printLine2("VFO To Channel?");
   }
   else {
-      if (splitOn == 1){
-        splitOn = 0;
-        printLineF2(F("Split Off!"));
-      }
-      else {
-        splitOn = 1;
-        if (ritOn == 1)
-          ritOn = 0;
-        printLineF2(F("Split On!"));
-      }
     delay_background(500, 0);
-    printLine2ClearAndUpdate();
-    menuOn = 0;
-  }
-}
 
-/*
-//Select CW Key Type by KD8CEC
-void menuSetupKeyType(int btn){
-  if (!btn && digitalRead(PTT) == HIGH){
-      if (Iambic_Key)
-        printLineF2(F("Key: Straight?"));
-      else
-        printLineF2(F("Key: Fn=A, PTT=B"));
-  }
-  else {
-      if (Iambic_Key)
-      {
-        printLineF2(F("Straight Key!"));
-        Iambic_Key = false;
-      }
-      else
-      {
-        Iambic_Key = true;
-        if (btn)
+    while(!btnDown()){
+      if (isDisplayInfo == 1) {
+        //Display Channel info *********************************
+        memset(c, 0, sizeof(c));
+
+        if (selectChannel >= 20 || selectChannel <=-1)
         {
-          keyerControl &= ~IAMBICB;
-          printLineF2(F("IAMBICA Key!"));
+          strcpy(c, "Exit setup?");
         }
         else
         {
-          keyerControl |= IAMBICB;
-          printLineF2(F("IAMBICB Key!"));
+          //Read Frequency from eeprom
+          EEPROM.get(CHANNEL_FREQ + 4 * selectChannel, resultFreq);
+          
+          loadMode = (byte)(resultFreq >> 29);
+          resultFreq = resultFreq & 0x1FFFFFFF;
+
+          //display channel description
+          if (selectChannel < 10 && EEPROM.read(CHANNEL_DESC + 6 * selectChannel) == 0x03) {  //0x03 is display Chnnel Name
+            //display Channel Name
+            for (int i = 0; i < 5; i++)
+              c[i] = EEPROM.read(CHANNEL_DESC + 6 * selectChannel + i + 1);
+
+           c[5] = ':';
+          }
+          else {
+            //Display frequency
+            //1 LINE : Channel Information : CH00
+            strcpy(c, "CH");
+            if (selectChannel < 9)
+              c[2] = '0';
+            
+            ltoa(selectChannel + 1, b, 10);
+            strcat(c, b); //append channel Number;
+            strcat(c, " :"); //append channel Number;
+          }
+          /*
+          if (selectChannel < 10)
+            printLineFromEEPRom(0, 4, 0, userCallsignLength -1); //eeprom to lcd use offset (USER_CALLSIGN_DAT)        
+          */
+  
+          //display frequency
+          tmpFreq = resultFreq;
+          for (int i = 15; i >= 6; i--) {
+            if (tmpFreq > 0) {
+              if (i == 12 || i == 8) c[i] = '.';
+              else {
+                c[i] = tmpFreq % 10 + 0x30;
+                tmpFreq /= 10;
+              }
+            }
+            else
+              c[i] = ' ';
+          }
+        }
+
+        printLine2(c);
+        
+        isDisplayInfo = 0;
+      }
+
+      knob = enc_read();
+
+      if (knob != 0)
+      {
+        moveStep += (knob > 0 ? 1 : -1);
+        if (moveStep < -3) {
+          if (selectChannel > -1)
+            selectChannel--;
+
+          isDisplayInfo = 1;
+          moveStep = 0;
+        }
+        else if (moveStep > 3) {
+          if (selectChannel < 20)
+            selectChannel++;
+            
+          isDisplayInfo = 1;
+          moveStep = 0;
         }
       }
-      
-    delay_background(500, 0);
-    printLine2ClearAndUpdate();
-    menuOn = 0;
+
+      Check_Cat(0);  //To prevent disconnections
+    } //end of while (knob)
+
+    if (selectChannel < 20 && selectChannel >= 0)
+    {
+      if (isMemoryToVfo == 1)
+      {
+        if (resultFreq > 3000 && resultFreq < 60000000)
+        setFrequency(resultFreq);
+        byteToMode(loadMode, 1);
+      }
+      else
+      {
+        //Save current Frequency to Channel (selectChannel)
+        EEPROM.put(CHANNEL_FREQ + 4 * selectChannel, (frequency & 0x1FFFFFFF) | (modeToByte() << 29) );
+        printLine2("Saved Frequency");
+      }
+    }
+    
+    menuClearExit(500);
   }
 }
-*/
+
 
 //Select CW Key Type by KD8CEC
 void menuSetupKeyType(int btn){
@@ -572,10 +539,11 @@ void menuSetupKeyType(int btn){
       else
         keyerControl |= IAMBICB;
     }
-    delay_background(2000, 0);
-    
-    printLine2ClearAndUpdate();
-    menuOn = 0;
+
+    //delay_background(2000, 0);
+    //printLine2ClearAndUpdate();
+    //menuOn = 0;
+    menuClearExit(1000);
   }
 }
 
@@ -655,10 +623,110 @@ void menuADCMonitor(int btn){
     delay_background(200, 0);
   } //end of while
       
-  printLine2ClearAndUpdate();
-  menuOn = 0;
+  //printLine2ClearAndUpdate();
+  //menuOn = 0;
+  menuClearExit(0);
 }
 
+//VFO Toggle and save VFO Information, modified by KD8CEC
+void menuVfoToggle(int btn, char isUseDelayTime)
+{
+  if (!btn){
+    if (vfoActive == VFO_A)
+      printLineF2(F("Select VFO B?"));
+    else
+      printLineF2(F("Select VFO A?"));    
+  }
+  else {
+      FrequencyToVFO(1);
+    
+      if (vfoActive == VFO_B){
+        //vfoB = frequency;
+        //vfoB_mode = modeToByte();
+        //storeFrequencyAndMode(2); //vfoB -> eeprom
+        
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        saveCheckFreq = frequency;
+        byteToMode(vfoA_mode, 0);
+        //printLineF2(F("Selected VFO A"));
+      }
+      else {
+        //vfoA = frequency;
+        //vfoA_mode = modeToByte();
+        //storeFrequencyAndMode(1); //vfoA -> eeprom
+        
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        saveCheckFreq = frequency;
+        byteToMode(vfoB_mode, 0);
+        //printLineF2(F("Selected VFO B"));
+      }
+
+      ritDisable();
+      setFrequency(frequency);
+
+      //if (isUseDelayTime == 1)        //Found Issue in wsjt-x Linux 32bit 
+      //  delay_background(500, 0);
+
+      //printLine2ClearAndUpdate();
+      //menuOn = 0;
+      menuClearExit(0);
+  }
+}
+
+void menuRitToggle(int btn){
+  if (!btn){
+    if (ritOn == 1)
+      printLineF2(F("RIT:On, Off?"));
+    else
+      printLineF2(F("RIT:Off, On?"));
+  }
+  else {
+      if (ritOn == 0){
+        printLineF2(F("RIT is ON"));
+        //enable RIT so the current frequency is used at transmit
+        ritEnable(frequency);
+      }
+      else{
+        printLineF2(F("RIT is OFF"));
+        ritDisable();
+      }
+      //delay_background(500, 0);
+      //printLine2ClearAndUpdate();
+      //menuOn = 0;
+      menuClearExit(500);
+  }
+}
+
+//Split communication using VFOA and VFOB by KD8CEC
+void menuSplitOnOff(int btn){
+  if (!btn){
+    if (splitOn == 0)
+      printLineF2(F("Split On?"));
+    else
+      printLineF2(F("Split Off?"));
+  }
+  else {
+      if (splitOn == 1){
+        splitOn = 0;
+        printLineF2(F("Split Off!"));
+      }
+      else {
+        splitOn = 1;
+        if (ritOn == 1)
+          ritOn = 0;
+        printLineF2(F("Split On!"));
+      }
+      
+    //delay_background(500, 0);
+    //printLine2ClearAndUpdate();
+    //menuOn = 0;
+    menuClearExit(500);
+  }
+}
+
+
 //Function to disbled transmission
 //by KD8CEC
 void menuTxOnOff(int btn, byte optionType){
@@ -677,9 +745,11 @@ void menuTxOnOff(int btn, byte optionType){
         isTxType &= ~(optionType);
         printLineF2(F("TX ON!"));
       }
-    delay_background(500, 0);
-    printLine2ClearAndUpdate();
-    menuOn = 0;
+      
+    //delay_background(500, 0);
+    //printLine2ClearAndUpdate();
+    //menuOn = 0;
+    menuClearExit(500);
   }
 }
 
@@ -702,21 +772,19 @@ void menuSetup(int btn){
       modeCalibrate = false;
       printLineF2(F("Setup:Off"));
     }
-   delay_background(2000, 0);
-   printLine2Clear();
-   menuOn = 0;
+   //delay_background(2000, 0);
+   //printLine2Clear();
+   //menuOn = 0;
+   menuClearExit(1000);
   }
 }
 
 void menuExit(int btn){
-
   if (!btn){
       printLineF2(F("Exit Menu?"));
   }
-  else{
-      printLine2ClearAndUpdate();
-      menuOn = 0;
-  }
+  else
+   menuClearExit(0);
 }
 
 void menuCWSpeed(int btn){
@@ -768,10 +836,11 @@ void menuCWSpeed(int btn){
       printLineF2(F("CW Speed set!"));
       cwSpeed = 1200/wpm;
       EEPROM.put(CW_SPEED, cwSpeed);
-      delay_background(2000, 0);
     //}
-    printLine2ClearAndUpdate();
-    menuOn = 0;
+    //delay_background(2000, 0);
+    //printLine2ClearAndUpdate();
+    //menuOn = 0;
+   menuClearExit(1000);
 }
 
 //Builtin CW Keyer Logic by KD8CEC
@@ -841,10 +910,11 @@ void menuSetupCwDelay(int btn){
       printLineF2(F("CW Delay set!"));
       cwDelayTime = tmpCWDelay / 10;
       EEPROM.put(CW_DELAY, cwDelayTime);
-      delay_background(2000, 0);
+      //delay_background(2000, 0);
     //}
-    printLine2ClearAndUpdate();
-    menuOn = 0;
+    //printLine2ClearAndUpdate();
+    //menuOn = 0;
+   menuClearExit(1000);
 }
 
 //CW Time delay by KD8CEC
@@ -890,10 +960,11 @@ void menuSetupTXCWInterval(int btn){
       printLineF2(F("CW Start set!"));
       delayBeforeCWStartTime = tmpTXCWInterval / 2;
       EEPROM.put(CW_START, delayBeforeCWStartTime);
-      delay_background(2000, 0);
+      //delay_background(2000, 0);
     //}
-    printLine2ClearAndUpdate();
-    menuOn = 0;
+    //printLine2ClearAndUpdate();
+    //menuOn = 0;
+   menuClearExit(1000);
 }
 
 
@@ -976,7 +1047,8 @@ void factoryCalibration(int btn){
 
   while(btnDown())
     delay(50);
-  delay(100);
+
+  menuClearExit(100);
 }
 
 void menuSetupCalibration(int btn){
@@ -1040,8 +1112,9 @@ void menuSetupCalibration(int btn){
   initOscillators();
   //si5351_set_calibration(calibration);
   setFrequency(frequency);    
-  printLine2ClearAndUpdate();
-  menuOn = 0;
+  //printLine2ClearAndUpdate();
+  //menuOn = 0;
+  menuClearExit(0);
 }
 
 void printCarrierFreq(unsigned long freq){
@@ -1114,8 +1187,9 @@ void menuSetupCarrier(int btn){
     si5351bx_setfreq(0, cwmCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
   
   setFrequency(frequency);    
-  printLine2ClearAndUpdate();
-  menuOn = 0; 
+  //printLine2ClearAndUpdate();
+  //menuOn = 0; 
+  menuClearExit(0);
 }
 
 //Append by KD8CEC
@@ -1150,8 +1224,9 @@ void menuSetupCWCarrier(int btn){
     si5351bx_setfreq(0, cwmCarrier);
     printCarrierFreq(cwmCarrier);
 
-    Check_Cat(0);  //To prevent disconnections
-    delay(100);
+    //Check_Cat(0);  //To prevent disconnections
+    //delay(100);
+    delay_background(100, 0);
   }
 
   //save the setting
@@ -1168,10 +1243,12 @@ void menuSetupCWCarrier(int btn){
   else
     si5351bx_setfreq(0, cwmCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
   
-  setFrequency(frequency);    
-  printLine2ClearAndUpdate();
-  menuOn = 0; 
+  setFrequency(frequency);
+  //printLine2ClearAndUpdate();
+  //menuOn = 0; 
+  menuClearExit(0);
 }
+
 //Modified by KD8CEC
 void menuSetupCwTone(int btn){
     int knob = 0;
@@ -1204,21 +1281,23 @@ void menuSetupCwTone(int btn){
       itoa(sideTone, b, 10);
       printLine2(b);
 
-      delay(100);
-      Check_Cat(0);  //To prevent disconnections
+      //delay(100);
+      //Check_Cat(0);  //To prevent disconnections
+      delay_background(100, 0);
     }
     noTone(CW_TONE);
     //save the setting
     if (digitalRead(PTT) == LOW){
       printLineF2(F("Sidetone set!"));
-      EEPROM.put(CW_SIDETONE, usbCarrier);
+      EEPROM.put(CW_SIDETONE, sideTone);
       delay_background(2000, 0);
     }
     else
       sideTone = prev_sideTone;
     
-    printLine2ClearAndUpdate();
-    menuOn = 0; 
+    //printLine2ClearAndUpdate();
+    //menuOn = 0; 
+  menuClearExit(0);
  }
 
 //Lock Dial move by KD8CEC
@@ -1256,8 +1335,9 @@ void doMenu(){
 
   //Appened Lines by KD8CEC for Adjust Tune step and Set Dial lock
   while(btnDown()){
-    delay(50);
-    Check_Cat(0);  //To prevent disconnections
+    //delay(50);
+    //Check_Cat(0);  //To prevent disconnections
+    delay_background(50, 0);
     
     if (btnDownTimeCount++ == (PRESS_ADJUST_TUNE / 50)) { //Set Tune Step 
       printLineF2(F("Set Tune Step?"));
@@ -1280,8 +1360,9 @@ void doMenu(){
     
     while (digitalRead(PTT) == HIGH && !btnDown())
     {
-      Check_Cat(0);  //To prevent disconnections
-      delay(50);  //debounce    
+      //Check_Cat(0);  //To prevent disconnections
+      //delay(50);  //debounce    
+      delay_background(50, 0);
 
       if (isNeedDisplay) {
         strcpy(b, "Tune Step:");
@@ -1320,7 +1401,6 @@ void doMenu(){
   }   //set tune step
 
   //Below codes are origial code with modified by KD8CEC
-  //Select menu
   menuOn = 2;
   
   while (menuOn){
@@ -1328,9 +1408,9 @@ void doMenu(){
     btnState = btnDown();
 
     if (i > 0){
-      if (modeCalibrate && select + i < 200)
+      if (modeCalibrate && select + i < 220)
         select += i;
-      if (!modeCalibrate && select + i < 100)
+      if (!modeCalibrate && select + i < 120)
         select += i;
     }
     //if (i < 0 && select - i >= 0)
@@ -1348,36 +1428,40 @@ void doMenu(){
     else if (select < 40)
       menuRitToggle(btnState);
     else if (select < 50)
-      menuIFSToggle(btnState);
+      menuIFSSetup(btnState);
     else if (select < 60)
       menuCWSpeed(btnState);
     else if (select < 70)
-      menuSplitOnOff(btnState);      //SplitOn / off
+      menuSplitOnOff(btnState);       //SplitOn / off
     else if (select < 80)
-      menuCWAutoKey(btnState);
+      menuCHMemory(btnState, 0);      //VFO to Memroy
     else if (select < 90)
-      menuSetup(btnState);
+      menuCHMemory(btnState, 1);      //Memory to VFO
     else if (select < 100)
+      menuCWAutoKey(btnState);
+    else if (select < 110)
+      menuSetup(btnState);
+    else if (select < 120)
       menuExit(btnState);
-    else if (select < 110 && modeCalibrate)
-      menuSetupCalibration(btnState);   //crystal
-    else if (select < 120 && modeCalibrate)
-      menuSetupCarrier(btnState);       //lsb
     else if (select < 130 && modeCalibrate)
-      menuSetupCWCarrier(btnState);       //lsb
+      menuSetupCalibration(btnState);   //crystal
     else if (select < 140 && modeCalibrate)
-      menuSetupCwTone(btnState);
+      menuSetupCarrier(btnState);       //lsb
     else if (select < 150 && modeCalibrate)
-      menuSetupCwDelay(btnState);
+      menuSetupCWCarrier(btnState);       //lsb
     else if (select < 160 && modeCalibrate)
-      menuSetupTXCWInterval(btnState);
+      menuSetupCwTone(btnState);
     else if (select < 170 && modeCalibrate)
-      menuSetupKeyType(btnState);
+      menuSetupCwDelay(btnState);
     else if (select < 180 && modeCalibrate)
-      menuADCMonitor(btnState);
+      menuSetupTXCWInterval(btnState);
     else if (select < 190 && modeCalibrate)
-      menuTxOnOff(btnState, 0x01);      //TX OFF / ON
+      menuSetupKeyType(btnState);
     else if (select < 200 && modeCalibrate)
+      menuADCMonitor(btnState);
+    else if (select < 210 && modeCalibrate)
+      menuTxOnOff(btnState, 0x01);      //TX OFF / ON
+    else if (select < 220 && modeCalibrate)
       menuExit(btnState);
 
     Check_Cat(0);  //To prevent disconnections
@@ -1385,9 +1469,8 @@ void doMenu(){
 
   //debounce the button
   while(btnDown()){
-    delay(50);
-    Check_Cat(0);  //To prevent disconnections
+    delay_background(50, 0);  //To prevent disconnections
   }
-  delay(50);
+  //delay(50);
 }
 

ubitx_20/ubitx_ui.ino

@@ -235,7 +235,6 @@ char byteToChar(byte srcByte){
 void updateDisplay() {
   // tks Jack Purdum W8TEE
   // replaced fsprint commmands by str commands for code size reduction
-  
   // replace code for Frequency numbering error (alignment, point...) by KD8CEC
   int i;
   unsigned long tmpFreq = frequency; //