Update ubitx_20.ino

ubitx_20/cat_libs.ino

@@ -109,7 +109,8 @@ void CatSetFreq(byte fromType)
 //#define BCD_LEN 9
 //PROTOCOL : 0x03
 //Computer <-(frequency)-> TRCV CAT_BUFF
-void CatGetFreqMode(unsigned long freq, byte fromType)
+//void CatGetFreqMode(unsigned long freq, byte fromType)
+void CatGetFreqMode(unsigned long freq) //for remove warning messages
 {
   int i;
   byte tmpValue;
@@ -149,15 +150,21 @@ void CatGetFreqMode(unsigned long freq, byte fromType)
   SendCatData(5);
 }
 
-void CatSetSplit(boolean isSplit, byte fromType)
+//void CatSetSplit(boolean isSplit, byte fromType)
+void CatSetSplit(boolean isSplit) //for remove warning messages
 {
+  if (isSplit)
+    splitOn = 1;
+  else
+    splitOn = 0;
     
   Serial.write(ACK);
 }
 
 void CatSetPTT(boolean isPTTOn, byte fromType)
 {
-  if (fromType == 2 || fromType == 3) {
+  //
+  if ((!inTx) && (fromType == 2 || fromType == 3)) {
     Serial.write(ACK);  
     return;  
   }
@@ -193,7 +200,7 @@ void CatSetPTT(boolean isPTTOn, byte fromType)
 void CatVFOToggle(boolean isSendACK, byte fromType)
 {
   if (fromType != 2 && fromType != 3) {
-    menuVfoToggle(1, 0);
+    menuVfoToggle(1);
   }  
 
   if (isSendACK)
@@ -232,7 +239,8 @@ void CatSetMode(byte tmpMode, byte fromType)
 }
 
 //Read EEProm by uBITX Manager Software
-void ReadEEPRom(byte fromType)
+//void ReadEEPRom(byte fromType)
+void ReadEEPRom() //for remove warnings.
 {
   //5BYTES
   //CAT_BUFF[0] [1] [2] [3] [4] //4 COMMAND
@@ -255,7 +263,8 @@ void ReadEEPRom(byte fromType)
 }
 
 //Write just proecess 1byes
-void WriteEEPRom(byte fromType)
+//void WriteEEPRom(byte fromType)
+void WriteEEPRom(void)  //for remove warning
 {
   //5BYTES
   uint16_t eepromStartIndex = CAT_BUFF[0] + CAT_BUFF[1] * 256;
@@ -275,7 +284,8 @@ void WriteEEPRom(byte fromType)
   }
 }
 
-void ReadEEPRom_FT817(byte fromType)
+//void ReadEEPRom_FT817(byte fromType)
+void ReadEEPRom_FT817(void) //for remove warnings
 {
   byte temp0 = CAT_BUFF[0];
   byte temp1 = CAT_BUFF[1];
@@ -601,7 +611,8 @@ void WriteEEPRom_FT817(byte fromType)
   Serial.write(ACK);
 }
 
-void CatRxStatus(byte fromType) 
+//void CatRxStatus(byte fromType) 
+void CatRxStatus(void)  //for remove warning
 {
   byte sMeterValue = 1;
 
@@ -621,7 +632,8 @@ void CatRxStatus(byte fromType)
 }
 
 
-void CatTxStatus(byte fromType)
+//void CatTxStatus(byte fromType)
+void CatTxStatus(void)  //for remove warning
 {
   boolean isHighSWR = false;
   boolean isSplitOn = false;
@@ -722,11 +734,11 @@ void Check_Cat(byte fromType)
       
     case 0x02 : //Split On
     case 0x82:  //Split Off
-      CatSetSplit(CAT_BUFF[4] == 0x02, fromType);
+      CatSetSplit(CAT_BUFF[4] == 0x02);
       break;
 
     case 0x03 :   //Read Frequency and mode
-      CatGetFreqMode(frequency, fromType);
+      CatGetFreqMode(frequency);
       break;
 
     case 0x07 :   //Set Operating  Mode
@@ -743,24 +755,24 @@ void Check_Cat(byte fromType)
       break;
 
     case 0xDB:  //Read uBITX EEPROM Data
-      ReadEEPRom(fromType); //Call by uBITX Manager Program
+      ReadEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBB:  //Read FT-817 EEPROM Data  (for comfirtable)
-      ReadEEPRom_FT817(fromType);
+      ReadEEPRom_FT817();
       break;
 
     case 0xDC:  //Write uBITX EEPROM Data
-      WriteEEPRom(fromType); //Call by uBITX Manager Program
+      WriteEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBC:  //Write FT-817 EEPROM Data  (for comfirtable)
       WriteEEPRom_FT817(fromType);
       break;
 
     case 0xE7 :       //Read RX Status
-      CatRxStatus(fromType);
+      CatRxStatus();
       break;
     case 0xF7:      //Read TX Status
-      CatTxStatus(fromType);
+      CatTxStatus();
       break;
     default:
     /*

ubitx_20/cw_autokey.ino

@@ -36,7 +36,7 @@
 //27 + 10 + 18 + 1(SPACE) = //56 
 const PROGMEM uint8_t cwAZTable[27] = {0b00100100 , 0b01001000 , 0b01001010 , 0b00111000 , 0b00010000, 0b01000010, 0b00111100, 0b01000000 , //A ~ H
 0b00100000, 0b01000111 ,0b00111010, 0b01000100, 0b00101100, 0b00101000 , 0b00111110, 0b01000110, 0b01001101, 0b00110100, //I ~ R
-0b00110000, 0b00011000, 0b00110010, 0b01000001, 0b00110110, 0b01001001, 0b01001011, 0b00111000};  //S ~ Z
+0b00110000, 0b00011000, 0b00110010, 0b01000001, 0b00110110, 0b01001001, 0b01001011, 0b01001100};  //S ~ Z
 PGM_P pCwAZTable = reinterpret_cast<PGM_P>(cwAZTable);
 
 const PROGMEM uint8_t cw09Table[27] = {0b00011111, 0b00001111, 0b00000111, 0b00000011, 0b00000001, 0b00000000, 0b00010000, 0b00011000, 0b00011100, 0b00011110};
@@ -297,7 +297,7 @@ void controlAutoCW(){
               displayScrolStep = 0;
           }
           
-          printLineFromEEPRom(0, 2, cwStartIndex + displayScrolStep + CW_DATA_OFSTADJ, cwEndIndex + CW_DATA_OFSTADJ); 
+          printLineFromEEPRom(0, 2, cwStartIndex + displayScrolStep + CW_DATA_OFSTADJ, cwEndIndex + CW_DATA_OFSTADJ, 0); 
 
           byte diplayAutoCWLine = 0;
           if ((displayOption1 & 0x01) == 0x01)
@@ -365,6 +365,11 @@ void controlAutoCW(){
         //check interval time, if you want adjust interval between chars, modify below
         if (isAutoCWHold == 0 && (millis() - autoCWbeforeTime > cwSpeed * 3))
         {
+          if (!inTx){                                           //if not TX Status, change RX -> TX
+            keyDown = 0;
+            startTx(TX_CW, 0);  //disable updateDisplay Command for reduce latency time
+          }
+          
           sendCWChar(EEPROM.read(CW_AUTO_DATA + autoCWSendCharIndex++));
 
           if (autoCWSendCharIndex > autoCWSendCharEndIndex) {          //finish auto cw send

ubitx_20/ubitx.h

@@ -0,0 +1,80 @@
+/*************************************************************************
+  header file for C++ by KD8CEC
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+**************************************************************************/
+#define WSPR_COUNT       443   //WSPR_MESSAGE_COUNT
+#define WSPR_MESSAGE1    444   //
+#define WSPR_MESSAGE2    490   //
+#define WSPR_MESSAGE3    536   //
+#define WSPR_MESSAGE4    582   //
+
+#define WSPR_BAND_COUNT 3
+
+#define TX_SSB 0
+#define TX_CW 1
+
+
+extern void printLine1(const char *c);
+extern void printLine2(const char *c);
+extern void printLineF(char linenmbr, const __FlashStringHelper *c);
+extern void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetType);
+extern byte delay_background(unsigned delayTime, byte fromType);
+extern int btnDown(void);
+extern char c[30];
+extern char b[30];
+
+extern unsigned long frequency;
+
+#define printLineF1(x) (printLineF(1, x))
+#define printLineF2(x) (printLineF(0, x))
+
+
+/** 
+ *  The second set of 16 pins on the Raduino's bottom connector are have the three clock outputs and the digital lines to control the rig.
+ *  This assignment is as follows :
+ *    Pin   1   2    3    4    5    6    7    8    9    10   11   12   13   14   15   16
+ *         GND +5V CLK0  GND  GND  CLK1 GND  GND  CLK2  GND  D2   D3   D4   D5   D6   D7  
+ *  These too are flexible with what you may do with them, for the Raduino, we use them to :
+ *  - TX_RX line : Switches between Transmit and Receive after sensing the PTT or the morse keyer
+ *  - CW_KEY line : turns on the carrier for CW
+ */
+
+#define TX_RX (7)
+#define CW_TONE (6)
+#define TX_LPF_A (5)
+#define TX_LPF_B (4)
+#define TX_LPF_C (3)
+#define CW_KEY (2)
+
+//we directly generate the CW by programmin the Si5351 to the cw tx frequency, hence, both are different modes
+//these are the parameter passed to startTx
+#define TX_SSB 0
+#define TX_CW 1
+
+extern void si5351bx_init(void);
+extern void si5351bx_setfreq(uint8_t clknum, uint32_t fout);
+extern void si5351_set_calibration(int32_t cal);
+extern void initOscillators(void);
+extern void Set_WSPR_Param(void);
+extern void TXSubFreq(unsigned long P2);
+
+extern void startTx(byte txMode, byte isDisplayUpdate);
+extern void stopTx(void);
+extern void setTXFilters(unsigned long freq);
+
+extern void SendWSPRManage(void);
+extern byte WsprMSGCount;
+
+

ubitx_20/ubitx_20.ino

@@ -38,6 +38,7 @@
  */
 #include <Wire.h>
 #include <EEPROM.h>
+#include "ubitx.h"
 
 /**
     The main chip which generates upto three oscillators of various frequencies in the
@@ -160,7 +161,8 @@ int count = 0;          //to generally count ticks, loops, etc
 #define TX_TUNE_TYPE 261      //
 #define HAM_BAND_RANGE 262    //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
 #define HAM_BAND_FREQS 302    //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)
+#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+  
 
 //for reduce cw key error, eeprom address
 #define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
@@ -175,10 +177,24 @@ int count = 0;          //to generally count ticks, loops, etc
 #define CW_ADC_BOTH_FROM 356   //CW ADC Range BOTH from         (Lower 8 bit)
 #define CW_ADC_BOTH_TO   357   //CW ADC Range BOTH to           (Lower 8 bit)
 #define CW_KEY_TYPE      358
+#define CW_DISPLAY_SHIFT 359  //Transmits on CWL, CWU Mode, LCD Frequency shifts Sidetone Frequency. 
+                              //(7:Enable / Disable //0: enable, 1:disable, (default is applied shift)
+                              //6 : 0 : Adjust Pulus, 1 : Adjust Minus
+                              //0~5: Adjust Value : * 10 = Adjust Value (0~300)
+#define COMMON_OPTION0  360  //0: Confirm : CW Frequency Shift
+                              //1 : IF Shift Save
+                              //
+                              //
+                              //
+#define IF_SHIFTVALUE   363                                
 
 #define DISPLAY_OPTION1  361   //Display Option1
 #define DISPLAY_OPTION2  362   //Display Option2
 
+#define CHANNEL_FREQ    630   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define CHANNEL_DESC    710   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define RESERVE3        770   //Reserve3 between Channel and Firmware id check
+
 //Check Firmware type and version
 #define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
 #define VERSION_ADDRESS 779   //check Firmware version
@@ -260,9 +276,10 @@ byte sideToneSub = 0;
 //DialLock
 byte isDialLock = 0;  //000000[0]vfoB [0]vfoA 0Bit : A, 1Bit : B
 byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
-byte arTuneStep[5];
+long arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
+byte commonOption0 = 0;
 byte displayOption1 = 0;
 byte displayOption2 = 0;
 
@@ -280,6 +297,9 @@ bool Iambic_Key = true;
 #define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
 unsigned char keyerControl = IAMBICB;
 
+byte isShiftDisplayCWFreq = 1;  //Display Frequency 
+int shiftDisplayAdjustVal = 0;  //
+
 //Variables for auto cw mode
 byte isCWAutoMode = 0;          //0 : none, 1 : CW_AutoMode_Menu_Selection, 2 : CW_AutoMode Sending
 byte cwAutoTextCount = 0;       //cwAutoText Count
@@ -315,6 +335,10 @@ boolean modeCalibrate = false;//this mode of menus shows extended menus to calib
 
 unsigned long beforeIdle_ProcessTime = 0; //for check Idle time
 byte line2DisplayStatus = 0;  //0:Clear, 1 : menu, 1: DisplayFrom Idle, 
+char lcdMeter[17];
+
+byte isIFShift = 0;     //1 = ifShift, 2 extend
+int ifShiftValue = 0;  //
                               
 /**
  * Below are the basic functions that control the uBitx. Understanding the functions before 
@@ -377,7 +401,7 @@ void setNextHamBandFreq(unsigned long f, char moveDirection)
     resultFreq = (unsigned long)(hamBandRange[(unsigned char)findedIndex][0]) * 1000;
 
   setFrequency(resultFreq);
-  byteWithFreqToMode(loadMode);
+  byteToMode(loadMode, 1);
 }
 
 void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
@@ -392,7 +416,6 @@ void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
   When the delay is used, the program will generate an error because it is not communicating, 
   so Create a new delay function that can do background processing.
  */
- 
 unsigned long delayBeforeTime = 0;
 byte delay_background(unsigned delayTime, byte fromType){ //fromType : 4 autoCWKey -> Check Paddle
   delayBeforeTime = millis();
@@ -476,28 +499,29 @@ void setTXFilters(unsigned long freq){
  
 void setFrequency(unsigned long f){
   f = (f / arTuneStep[tuneStepIndex -1]) * arTuneStep[tuneStepIndex -1];
-  
   setTXFilters(f);
 
+  unsigned long appliedCarrier = ((cwMode == 0 ? usbCarrier : cwmCarrier) + (isIFShift && (inTx == 0) ? ifShiftValue : 0));
+
   if (cwMode == 0)
   {
     if (isUSB){
-      si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f);
+      si5351bx_setfreq(2, SECOND_OSC_USB - appliedCarrier + f);
       si5351bx_setfreq(1, SECOND_OSC_USB);
     }
     else{
-      si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f);
+      si5351bx_setfreq(2, SECOND_OSC_LSB + appliedCarrier + f);
       si5351bx_setfreq(1, SECOND_OSC_LSB);
     }
   }
   else
   {
     if (cwMode == 1){ //CWL
-      si5351bx_setfreq(2, SECOND_OSC_LSB + cwmCarrier + f);
+      si5351bx_setfreq(2, SECOND_OSC_LSB + appliedCarrier + f);
       si5351bx_setfreq(1, SECOND_OSC_LSB);
     }
     else{             //CWU
-      si5351bx_setfreq(2, SECOND_OSC_USB - cwmCarrier + f);
+      si5351bx_setfreq(2, SECOND_OSC_USB - appliedCarrier + f);
       si5351bx_setfreq(1, SECOND_OSC_USB);
     }
   }
@@ -510,7 +534,6 @@ void setFrequency(unsigned long f){
  * put the uBitx in tx mode. It takes care of rit settings, sideband settings
  * Note: In cw mode, doesnt key the radio, only puts it in tx mode
  */
- 
 void startTx(byte txMode, byte isDisplayUpdate){
   //Check Hamband only TX //Not found Hamband index by now frequency
   if (tuneTXType >= 100 && getIndexHambanBbyFreq(ritOn ? ritTxFrequency :  frequency) == -1) {
@@ -528,21 +551,25 @@ void startTx(byte txMode, byte isDisplayUpdate){
     ritRxFrequency = frequency;
     setFrequency(ritTxFrequency);
   }
-  else if (splitOn == 1) {
+  else 
+  {
+    if (splitOn == 1) {
       if (vfoActive == VFO_B) {
         vfoActive = VFO_A;
         frequency = vfoA;
-        byteToMode(vfoA_mode);
+        byteToMode(vfoA_mode, 0);
       }
       else if (vfoActive == VFO_A){
         vfoActive = VFO_B;
         frequency = vfoB;
-        byteToMode(vfoB_mode);
+        byteToMode(vfoB_mode, 0);
+      }
     }
 
     setFrequency(frequency);
   } //end of else
 
+  SetCarrierFreq();
 
   if (txMode == TX_CW){
     //turn off the second local oscillator and the bfo
@@ -575,34 +602,39 @@ void startTx(byte txMode, byte isDisplayUpdate){
     updateDisplay();
 }
 
-void stopTx(){
+void stopTx(void){
   inTx = 0;
 
   digitalWrite(TX_RX, 0);           //turn off the tx
 
+/*
   if (cwMode == 0)
-    si5351bx_setfreq(0, usbCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
   else
-    si5351bx_setfreq(0, cwmCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
+*/
+  SetCarrierFreq();
 
   if (ritOn)
     setFrequency(ritRxFrequency);
-  else if (splitOn == 1) {
+  else
+  {
+    if (splitOn == 1) {
       //vfo Change
       if (vfoActive == VFO_B){
         vfoActive = VFO_A;
         frequency = vfoA;
-        byteToMode(vfoA_mode);
+        byteToMode(vfoA_mode, 0);
       }
       else if (vfoActive == VFO_A){
         vfoActive = VFO_B;
         frequency = vfoB;
-        byteToMode(vfoB_mode);
+        byteToMode(vfoB_mode, 0);
       }
+    }
+    
     setFrequency(frequency);
   } //end of else
-  else
-    setFrequency(frequency);
   
   updateDisplay();
 }
@@ -666,7 +698,7 @@ void checkButton(){
     delay(10);
     Check_Cat(0);
   }
-  delay(50);//debounce
+  //delay(50);//debounce
 }
 
 
@@ -681,19 +713,17 @@ int encodedSumValue = 0;
 unsigned long lastTunetime = 0; //if continous moving, skip threshold processing
 byte lastMovedirection = 0; //0 : stop, 1 : cw, 2 : ccw
 
-#define skipThresholdTime 100
+//#define skipThresholdTime 70
 #define encodeTimeOut 1000
 
 void doTuningWithThresHold(){
   int s = 0;
   unsigned long prev_freq;
-  long incdecValue = 0;
 
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02)))
     return;
 
-  if (isCWAutoMode == 0 || cwAutoDialType == 1)
   s = enc_read();
 
   //if time is exceeded, it is recognized as an error,
@@ -711,7 +741,9 @@ void doTuningWithThresHold(){
   encodedSumValue += (s > 0 ? 1 : -1);
 
   //check threshold and operator actions (hold dial speed = continous moving, skip threshold check)
-  if ((lastTunetime < millis() - skipThresholdTime) && ((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
+  //not use continues changing by Threshold
+  //if ((lastTunetime < (millis() - skipThresholdTime)) && ((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
+  if (((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
     return;
 
   lastTunetime = millis();
@@ -721,7 +753,8 @@ void doTuningWithThresHold(){
 
   prev_freq = frequency;
   //incdecValue = tuningStep * s;
-  frequency += (arTuneStep[tuneStepIndex -1] * s * (s * s < 10 ? 1 : 3));  //appield weight (s is speed)
+  //frequency += (arTuneStep[tuneStepIndex -1] * s * (s * s < 10 ? 1 : 3));  //appield weight (s is speed)
+  frequency += (arTuneStep[tuneStepIndex -1] * s);  //appield weight (s is speed) //if want need more increase size, change step size
     
   if (prev_freq < 10000000l && frequency > 10000000l)
     isUSB = true;
@@ -741,9 +774,9 @@ void doRIT(){
   unsigned long old_freq = frequency;
 
   if (knob < 0)
-    frequency -= 100l;
+    frequency -= (arTuneStep[tuneStepIndex -1]);  //
   else if (knob > 0)
-    frequency += 100;
+    frequency += (arTuneStep[tuneStepIndex -1]);  //
  
   if (old_freq != frequency){
     setFrequency(frequency);
@@ -751,8 +784,8 @@ void doRIT(){
   }
 }
 
-/**
+/*
- save Frequency and mode to eeprom
+ save Frequency and mode to eeprom for Auto Save with protected eeprom cycle, by kd8cec
  */
 void storeFrequencyAndMode(byte saveType)
 {
@@ -784,6 +817,22 @@ void storeFrequencyAndMode(byte saveType)
   }
 }
 
+//calculate step size from 1 byte, compatible uBITX Manager, by KD8CEC
+unsigned int byteToSteps(byte srcByte) {
+    byte powerVal = (byte)(srcByte >> 6);
+    unsigned int baseVal = srcByte & 0x3F;
+
+    if (powerVal == 1)
+        return baseVal * 10;
+    else if (powerVal == 2)
+        return baseVal * 100;
+    else if (powerVal == 3)
+        return baseVal * 1000;
+    else
+        return baseVal;
+}
+
+
 /**
  * The settings are read from EEPROM. The first time around, the values may not be 
  * present or out of range, in this case, some intelligent defaults are copied into the 
@@ -847,13 +896,14 @@ void initSettings(){
   else
   {
     Iambic_Key = true;
-    if (cwKeyType = 1)
+    if (cwKeyType == 1)
       keyerControl &= ~IAMBICB;
     else
       keyerControl |= IAMBICB;
   }
     
 
+  EEPROM.get(COMMON_OPTION0, commonOption0);
   EEPROM.get(DISPLAY_OPTION1, displayOption1);
   EEPROM.get(DISPLAY_OPTION2, displayOption2);
 
@@ -884,13 +934,13 @@ void initSettings(){
   if ((3 < tuneTXType && tuneTXType < 100) || 103 < tuneTXType || useHamBandCount < 1 || findedValidValueCount < 5)
   {
     tuneTXType = 2;
-    //if empty band Information, auto insert default region 1 frequency range
+    //if empty band Information, auto insert default region 2 frequency range
     //This part is made temporary for people who have difficulty setting up, so can remove it when you run out of memory.
     useHamBandCount = 10;
     hamBandRange[0][0] = 1810; hamBandRange[0][1] = 2000; 
     hamBandRange[1][0] = 3500; hamBandRange[1][1] = 3800; 
     hamBandRange[2][0] = 5351; hamBandRange[2][1] = 5367; 
-    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;   //region 1
+    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;     //region 2
     hamBandRange[4][0] = 10100; hamBandRange[4][1] = 10150; 
     hamBandRange[5][0] = 14000; hamBandRange[5][1] = 14350; 
     hamBandRange[6][0] = 18068; hamBandRange[6][1] = 18168; 
@@ -904,8 +954,8 @@ void initSettings(){
   findedValidValueCount = 0;
   EEPROM.get(TUNING_STEP, tuneStepIndex);
   for (byte i = 0; i < 5; i++) {
-    arTuneStep[i] = EEPROM.read(TUNING_STEP + i + 1);
+    arTuneStep[i] = byteToSteps(EEPROM.read(TUNING_STEP + i + 1));
-    if (arTuneStep[i] >= 1 && arTuneStep[i] < 251) //Maximum 250 for check valid Value
+    if (arTuneStep[i] >= 1 && arTuneStep[i] <= 60000) //Maximum 650 for check valid Value
        findedValidValueCount++;
   }
 
@@ -938,6 +988,33 @@ void initSettings(){
   cwAdcBothFrom = EEPROM.read(CW_ADC_BOTH_FROM) | ((tmpMostBits & 0x30) << 4);
   cwAdcBothTo = EEPROM.read(CW_ADC_BOTH_TO)     | ((tmpMostBits & 0xC0) << 2);
 
+  //Display Type for CW mode
+  isShiftDisplayCWFreq = EEPROM.read(CW_DISPLAY_SHIFT);
+
+  //Enable / Diable Check for CW Display Cofiguration Group 
+  if ((commonOption0 & 0x80) != 0x00)
+  {
+    //Adjust CW Mode Freq
+    shiftDisplayAdjustVal = (isShiftDisplayCWFreq & 0x3F) * 10;
+  
+    //check Minus
+    if ((isShiftDisplayCWFreq & 0x40) == 0x40)
+      shiftDisplayAdjustVal = shiftDisplayAdjustVal * -1;
+  
+   //Shift Display Check (Default : 0)
+    if ((isShiftDisplayCWFreq & 0x80) == 0)  //Enabled
+      isShiftDisplayCWFreq = 1;
+    else    //Disabled
+      isShiftDisplayCWFreq = 0;
+  }
+
+   //Stored IF Shift Option
+  if ((commonOption0 & 0x40) != 0x00)
+  {
+    EEPROM.get(IF_SHIFTVALUE, ifShiftValue);
+    isIFShift = ifShiftValue != 0;
+  }
+
   //default Value (for original hardware)
   if (cwAdcSTFrom >= cwAdcSTTo)
   {
@@ -974,19 +1051,19 @@ void initSettings(){
 
   //original code with modified by kd8cec
   if (usbCarrier > 12010000l || usbCarrier < 11990000l)
-    usbCarrier = 11995000l;
+    usbCarrier = 11997000l;
 
   if (cwmCarrier > 12010000l || cwmCarrier < 11990000l)
-    cwmCarrier = 11995000l;
+    cwmCarrier = 11997000l;
     
   if (vfoA > 35000000l || 3500000l > vfoA) {
      vfoA = 7150000l;
-     vfoA_mode = 2;
+     vfoA_mode = 2; //LSB
   }
   
   if (vfoB > 35000000l || 3500000l > vfoB) {
      vfoB = 14150000l;  
-     vfoB_mode = 3;
+     vfoB_mode = 3; //USB
   }
   //end of original code section
 
@@ -1012,7 +1089,6 @@ void initSettings(){
 }
 
 void initPorts(){
-
   analogReference(DEFAULT);
 
   //??
@@ -1062,7 +1138,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.33")); 
+  printLineF(1, F("CE v1.061")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -1070,7 +1146,7 @@ void setup()
 
   if (userCallsignLength > 0 && ((userCallsignLength & 0x80) == 0x80)) {
     userCallsignLength = userCallsignLength & 0x7F;
-    printLineFromEEPRom(0, 0, 0, userCallsignLength -1); //eeprom to lcd use offset (USER_CALLSIGN_DAT)
+    printLineFromEEPRom(0, 0, 0, userCallsignLength -1, 0); //eeprom to lcd use offset (USER_CALLSIGN_DAT)
     delay(500);
   }
   else {
@@ -1081,7 +1157,7 @@ void setup()
   
   initPorts();     
 
-  byteToMode(vfoA_mode);
+  byteToMode(vfoA_mode, 0);
   initOscillators();
 
   frequency = vfoA;
@@ -1093,14 +1169,7 @@ void setup()
     factory_alignment();
 }
 
-
+//Auto save Frequency and Mode with Protected eeprom life by KD8CEC
-/**
- * The loop checks for keydown, ptt, function button and tuning.
- */
-//for debug
-int dbgCnt = 0;
-byte flasher = 0;
-
 void checkAutoSaveFreqMode()
 {
   //when tx or ritOn, disable auto save
@@ -1118,18 +1187,8 @@ void checkAutoSaveFreqMode()
     //check time for Frequency auto save
     if (millis() - saveCheckTime > saveIntervalSec * 1000)
     {
-      if (vfoActive == VFO_A)
+      FrequencyToVFO(1);
-      {
+      saveCheckTime = 0;  //for reduce cpu use rate
-        vfoA = frequency;
-        vfoA_mode = modeToByte();
-        storeFrequencyAndMode(1);
-      }
-      else
-      {
-        vfoB = frequency;
-        vfoB_mode = modeToByte();
-        storeFrequencyAndMode(2);
-      }
     }
   }
 }
@@ -1147,18 +1206,21 @@ void loop(){
   
   //tune only when not tranmsitting 
   if (!inTx){
+    if (isCWAutoMode == 0 || cwAutoDialType == 1)
+    {
       if (ritOn)
         doRIT();
       else 
         doTuningWithThresHold();
+    }
 
-    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 500) {
+    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 250) {
       idle_process();
+      checkAutoSaveFreqMode();  //move here form out scope for reduce cpu use rate
       beforeIdle_ProcessTime = millis();
     }
   } //end of check TX Status
 
   //we check CAT after the encoder as it might put the radio into TX
   Check_Cat(inTx? 1 : 0);
-  checkAutoSaveFreqMode();
 }

ubitx_20/ubitx_idle.ino

@@ -17,24 +17,21 @@
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 **************************************************************************/
-byte line2Buffer[16];
+char line2Buffer[16];
 //KD8CEC 200Hz ST
 //L14.150 200Hz ST
 //U14.150 +150khz
 int freqScrollPosition = 0;
 //Example Line2 Optinal Display
-void updateLine2Buffer()
+//immediate execution, not call by scheulder
+void updateLine2Buffer(char isDirectCall)
 {
   unsigned long tmpFreq = 0;
-
+  if (isDirectCall == 0)
+  {
     if (ritOn)
     {
-    line2Buffer[0] = 'R';
+      strcpy(line2Buffer, "RitTX:");
-    line2Buffer[1] = 'i';
-    line2Buffer[2] = 't';
-    line2Buffer[3] = 'T';
-    line2Buffer[4] = 'X';
-    line2Buffer[5] = ':';
   
       //display frequency
       tmpFreq = ritTxFrequency;
@@ -51,17 +48,18 @@ void updateLine2Buffer()
       }
   
       return;
-  }
+    } //end of ritOn display
 
+    //======================================================
+    //other VFO display
+    //======================================================
     if (vfoActive == VFO_B)
     {
       tmpFreq = vfoA;
-    //line2Buffer[0] = 'A';
     }
     else 
     {
       tmpFreq = vfoB;
-    //line2Buffer[0] = 'B';
     }
   
     // EXAMPLE 1 & 2
@@ -80,18 +78,18 @@ void updateLine2Buffer()
     }
   
     //EXAMPLE #1
-  if ((displayOption1 & 0x04) == 0x00)
+    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
       line2Buffer[6] = 'k';
     else
     {
       //example #2
-    if (freqScrollPosition++ > 18)
+      if (freqScrollPosition++ > 18)    //none scroll display time
       {
         line2Buffer[6] = 'k';
         if (freqScrollPosition > 25)
           freqScrollPosition = -1;
       }
-    else
+      else                              //scroll frequency 
       {
         line2Buffer[10] = 'H';
         line2Buffer[11] = 'z';
@@ -113,21 +111,77 @@ void updateLine2Buffer()
               line2Buffer[i] = ' ';
         }
       }
-  }
+    } //scroll
-  line2Buffer[7] = ' ';
     
+    line2Buffer[7] = ' ';
+  } //check direct call by encoder
+  
+  if (isIFShift)
+  {
+    if (isDirectCall == 1)
+      for (int i = 0; i < 16; i++)
+        line2Buffer[i] = ' ';
+      
+      //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
+
+    //if (ifShiftValue == 0)
+    //{
+      /*
+      line2Buffer[10] = 'S';
+      line2Buffer[11] = ':';
+      line2Buffer[12] = 'O';
+      line2Buffer[13] = 'F';
+      line2Buffer[14] = 'F';
+      */
+    //}
+    //else
+    //{
+      line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+      line2Buffer[11] = 0;
+      line2Buffer[12] = ' ';
+    
+      //11, 12, 13, 14, 15
+      memset(b, 0, sizeof(b));
+      ltoa(ifShiftValue, b, DEC);
+      strncat(line2Buffer, b, 5);
+    //}
+    
+    if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
+        printLine2(line2Buffer);    
+  }       // end of display IF
+  else    // step display
+  {
+    if (isDirectCall != 0)
+      return;
+
+    memset(&line2Buffer[8], ' ', 8);
     //Step
-  byte tmpStep = arTuneStep[tuneStepIndex -1];
+    long tmpStep = arTuneStep[tuneStepIndex -1];
-  for (int i = 10; i >= 8; i--) {
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
       if (tmpStep > 0) {
-        line2Buffer[i] = tmpStep % 10 + 0x30;
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
           tmpStep /= 10;
       }
       else
-      line2Buffer[i] = ' ';
+        line2Buffer[i +isStepKhz] = ' ';
     }
+    //if (isStepKhz == 1)
+    //  line2Buffer[10] = 'k';
+
+    if (isStepKhz == 0)
+    {
       line2Buffer[11] = 'H';
       line2Buffer[12] = 'z';
+    }
   
     line2Buffer[13] = ' ';
     //if (
@@ -147,18 +201,53 @@ void updateLine2Buffer()
       line2Buffer[14] = 'I';
       line2Buffer[15] = 'B';
     }    
+  }
+  
 }
 
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  if (meterType == 0 || meterType == 1 || meterType == 2)
+  {
+    drawMeter(meterValue);  //call original source code
+    int lineNumber = 0;
+    if ((displayOption1 & 0x01) == 0x01)
+      lineNumber = 1;
+    
+    lcd.setCursor(drawPosition, lineNumber);
+  
+    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+      lcd.write(lcdMeter[i]);
+  }
+}
+
+byte testValue = 0;
+char checkCount = 0;
 void idle_process()
 {
   //space for user graphic display
   if (menuOn == 0)
   {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
     //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
     if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
-      updateLine2Buffer();
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
         printLine2(line2Buffer);
         line2DisplayStatus = 2;
+        checkCount = 0;
+      }
+
+      //EX for Meters
+      /*
+      DisplayMeter(0, testValue++, 7);
+      if (testValue > 30)
+        testValue = 0;
+      */
     }
   }
 }

ubitx_20/ubitx_keyer.ino

@@ -90,13 +90,13 @@ void cwKeyUp(){
 #define PDLSWAP 0x08 // 0 for normal, 1 for swap
 #define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
 enum KSTYPE {IDLE, CHK_DIT, CHK_DAH, KEYED_PREP, KEYED, INTER_ELEMENT };
-static long ktimer;
+static unsigned long ktimer;
 unsigned char keyerState = IDLE;
 
 //Below is a test to reduce the keying error. do not delete lines
 //create by KD8CEC for compatible with new CW Logic
 char update_PaddleLatch(byte isUpdateKeyState) {
-  unsigned char tmpKeyerControl;
+  unsigned char tmpKeyerControl = 0;
   int paddle = analogRead(ANALOG_KEYER);
 
   if (paddle >= cwAdcDashFrom && paddle <= cwAdcDashTo)
@@ -126,9 +126,7 @@ char update_PaddleLatch(byte isUpdateKeyState) {
 // modified by KD8CEC
 ******************************************************************************/
 void cwKeyer(void){
-  byte paddle;
   lastPaddle = 0;
-  int dot,dash;
   bool continue_loop = true;
   unsigned tmpKeyControl = 0;
   
@@ -170,14 +168,32 @@ void cwKeyer(void){
           break;
     
         case KEYED_PREP:
+          //modified KD8CEC
+          /*
           ktimer += millis(); // set ktimer to interval end time
           keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
           keyerState = KEYED; // next state
           if (!inTx){
+            //DelayTime Option
+            delay_background(delayBeforeCWStartTime * 2, 2);
+            
             keyDown = 0;
             cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
             startTx(TX_CW, 1);
           }
+          */
+          if (!inTx){
+            //DelayTime Option
+            delay_background(delayBeforeCWStartTime * 2, 2);
+            
+            keyDown = 0;
+            cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
+            startTx(TX_CW, 1);
+          }
+          ktimer += millis(); // set ktimer to interval end time
+          keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
+          keyerState = KEYED; // next state
+          
           cwKeydown();
           break;
     
@@ -206,7 +222,7 @@ void cwKeyer(void){
           break;
       }
   
-      Check_Cat(3);
+      Check_Cat(2);
     } //end of while
   }
   else{
@@ -214,6 +230,9 @@ void cwKeyer(void){
       if (update_PaddleLatch(0) == DIT_L) {
         // if we are here, it is only because the key is pressed
         if (!inTx){
+          //DelayTime Option
+          delay_background(delayBeforeCWStartTime * 2, 2);
+          
           keyDown = 0;
           cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT; 
           startTx(TX_CW, 1);
@@ -231,13 +250,14 @@ void cwKeyer(void){
           keyDown = 0;
           stopTx();
         }
-        if (!cwTimeout)
+        //if (!cwTimeout) //removed by KD8CEC
-          return;
+        //   return;
         // got back to the beginning of the loop, if no further activity happens on straight key
         // we will time out, and return out of this routine 
         //delay(5);
-        delay_background(5, 3);
+        //delay_background(5, 3); //removed by KD8CEC
-        continue;
+        //continue;               //removed by KD8CEC
+        return;                   //Tx stop control by Main Loop
       }
 
       Check_Cat(2);

ubitx_20/ubitx_si5351.ino

@@ -1,3 +1,19 @@
+/************************************************************************************
+ * KD8CEC 
+ * kd8cec@gmail.com   http://www.hamskey.com
+ * 
+ * Merge two SI5351 Librarys
+ * KE7ER's fixed vco and variable Clocks Configure values
+ * G3ZIL's fixed Clock Configure Value and variable VCO
+ *  * I have combined the two libraries above. All licenses follow the above library.
+ * 
+ * PLL-A is generated by fixing 850Mhz clock. All output clocks use PLL-A to 
+ * generate the frequency. This is the method used in QRP radios such as uBITX.
+ * When switching to WSPR transmission mode, PLL-B operates for the base frequency to transmit WSPR. 
+ * The output clock channel that controls the frequency is connected to the PLL-B. 
+ * The WSPR protocol is generated by changing the clock of the PLL-B.
+ ************************************************************************************/
+
 // *************  SI5315 routines - tks Jerry Gaffke, KE7ER   ***********************
 
 // An minimalist standalone set of Si5351 routines.
@@ -60,6 +76,7 @@ void i2cWriten(uint8_t reg, uint8_t *vals, uint8_t vcnt) {  // write array
   Wire.endTransmission();
 }
 
+uint8_t  si5351Val[8] = {0, 1, 0, 0, 0, 0, 0, 0}; //for reduce program memory size
 
 void si5351bx_init() {                  // Call once at power-up, start PLLA
   uint32_t msxp1;
@@ -68,11 +85,13 @@ void si5351bx_init() {                  // Call once at power-up, start PLLA
   i2cWrite(3, si5351bx_clken);          // Disable all CLK output drivers
   i2cWrite(183, SI5351BX_XTALPF << 6);  // Set 25mhz crystal load capacitance
   msxp1 = 128 * SI5351BX_MSA - 512;     // and msxp2=0, msxp3=1, not fractional
-  uint8_t  vals[8] = {0, 1, BB2(msxp1), BB1(msxp1), BB0(msxp1), 0, 0, 0};
+  //uint8_t  vals[8] = {0, 1, BB2(msxp1), BB1(msxp1), BB0(msxp1), 0, 0, 0};
-  i2cWriten(26, vals, 8);               // Write to 8 PLLA msynth regs
+  si5351Val[2] = BB2(msxp1);
+  si5351Val[3] = BB1(msxp1);
+  si5351Val[4] = BB0(msxp1);
+  
+  i2cWriten(26, si5351Val, 8);               // Write to 8 PLLA msynth regs
   i2cWrite(177, 0x20);                  // Reset PLLA  (0x80 resets PLLB)
-  // for (reg=16; reg<=23; reg++) i2cWrite(reg, 0x80);    // Powerdown CLK's
-  // i2cWrite(187, 0);                  // No fannout of clkin, xtal, ms0, ms4
 }
 
 void si5351bx_setfreq(uint8_t clknum, uint32_t fout) {  // Set a CLK to fout Hz
@@ -105,15 +124,48 @@ void si5351_set_calibration(int32_t cal){
     si5351bx_setfreq(0, usbCarrier);
 }
 
+void SetCarrierFreq()
+{
+  unsigned long appliedCarrier = ((cwMode == 0 ? usbCarrier : cwmCarrier) + (isIFShift && (inTx == 0) ? ifShiftValue : 0));
+  si5351bx_setfreq(0, appliedCarrier);
+
+    /*
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));
+  else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));
+    */
+}
+
 void initOscillators(){
   //initialize the SI5351
   si5351bx_init();
   si5351bx_vcoa = (SI5351BX_XTAL * SI5351BX_MSA) + calibration; // apply the calibration correction factor
+  SetCarrierFreq();
+}
 
-  if (cwMode == 0)
+//============================================================
-    si5351bx_setfreq(0, usbCarrier);
+// ADD FUNCTIONS by KD8CEC
- else
+//============================================================
-    si5351bx_setfreq(0, cwmCarrier);
+uint8_t Wspr_Reg1[8] = {0xFF,0xFE, 0x00, 0, 0, 0, 0, 0};  //3, 4, 5, 6, 7
+uint8_t Wspr_Reg2[8] = {0, 1, 0, 0, 0, 0, 0, 0};          //2, 3, 4
+
+void Set_WSPR_Param(void) 
+{ 
+  i2cWrite(18, 128);
+  i2cWriten(34, Wspr_Reg1, 8);
+  i2cWriten(58, Wspr_Reg2, 8);
+  i2cWrite(177, 128);
+  i2cWrite(18, 111);
+
+  si5351bx_clken &= ~(1 << 2);
+  i2cWrite(3, si5351bx_clken);
+}
+
+void TXSubFreq(unsigned long P2)
+{                   
+  i2cWrite(40, (P2 & 65280) >> 8);
+  i2cWrite(41, P2 & 255);
 }
 
 

ubitx_20/ubitx_ui.ino

@@ -9,7 +9,7 @@
 //#define printLineF2(x) (printLineF(0, x))
 
 //returns true if the button is pressed
-int btnDown(){
+int btnDown(void){
   if (digitalRead(FBUTTON) == HIGH)
     return 0;
   else
@@ -25,8 +25,8 @@ int btnDown(){
  * The current reading of the meter is assembled in the string called meter
  */
 
-//char meter[17];
 
+/*
 const PROGMEM uint8_t s_meter_bitmap[] = {
   B00000,B00000,B00000,B00000,B00000,B00100,B00100,B11011,
   B10000,B10000,B10000,B10000,B10100,B10100,B10100,B11011,
@@ -35,7 +35,18 @@ const PROGMEM uint8_t s_meter_bitmap[] = {
   B00010,B00010,B00010,B00010,B00110,B00110,B00110,B11011,
   B00001,B00001,B00001,B00001,B00101,B00101,B00101,B11011
 };
-PGM_P ps_meter_bitmap = reinterpret_cast<PGM_P>(s_meter_bitmap);
+*/
+
+const PROGMEM uint8_t meters_bitmap[] = {
+  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000 ,   //custom 1
+  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000 ,   //custom 2
+  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100 ,   //custom 3
+  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110 ,   //custom 4
+  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111 ,   //custom 5
+  B01000,  B11100,  B01000,  B00000,  B10111,  B10101,  B10101,  B10111     //custom 6
+};
+
+PGM_P p_metes_bitmap = reinterpret_cast<PGM_P>(meters_bitmap);
 
 const PROGMEM uint8_t lock_bitmap[8] = {
   0b01110,
@@ -60,38 +71,54 @@ void initMeter(){
   lcd.createChar(0, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i);
   lcd.createChar(1, tmpbytes);
 
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 8);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 8);
   lcd.createChar(2, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 16);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 16);
   lcd.createChar(3, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 24);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 24);
   lcd.createChar(4, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 28);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 32);
   lcd.createChar(5, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 32);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 40);
   lcd.createChar(6, tmpbytes);
 }
 
-/**
+//by KD8CEC
- * The meter is drawn with special characters.
+//0 ~ 25 : 30 over : + 10
- * character 1 is used to simple draw the blocks of the scale of the meter
+void drawMeter(int needle) {
- * characters 2 to 6 are used to draw the needle in positions 1 to within the block
+  //5Char + O over
- * This displays a meter from 0 to 100, -1 displays nothing
+  int i;
- */
 
- /*
+  for (i = 0; i < 5; i++) {
+    if (needle >= 5)
+      lcdMeter[i] = 5; //full
+    else if (needle > 0)
+      lcdMeter[i] = needle; //full
+    else  //0
+      lcdMeter[i] = 0x20;
+    
+    needle -= 5;
+  }
+
+  if (needle > 0)
+    lcdMeter[5] = 6;
+  else
+    lcdMeter[5] = 0x20;
+}
+
+/*
 void drawMeter(int8_t needle){
   int16_t best, i, s;
 
@@ -101,19 +128,18 @@ void drawMeter(int8_t needle){
   s = (needle * 4)/10;
   for (i = 0; i < 8; i++){
     if (s >= 5)
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     else if (s >= 0)
-      meter[i] = 2 + s;
+      lcdMeter[i] = 2 + s;
     else
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     s = s - 5;
   }
   if (needle >= 40)
-    meter[i-1] = 6;
+    lcdMeter[i-1] = 6;
-  meter[i] = 0;
+  lcdMeter[i] = 0;
 }
 */
-
 // The generic routine to display one line on the LCD 
 void printLine(unsigned char linenmbr, const char *c) {
   if ((displayOption1 & 0x01) == 0x01)
@@ -147,7 +173,7 @@ void printLineF(char linenmbr, const __FlashStringHelper *c)
 }
 
 #define LCD_MAX_COLUMN 16
-void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex) {
+void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetTtype) {
   if ((displayOption1 & 0x01) == 0x01)
     linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
   
@@ -156,7 +182,7 @@ void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, b
   for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
   {
     if (++lcdColumn <= LCD_MAX_COLUMN)
-      lcd.write(EEPROM.read(USER_CALLSIGN_DAT + i));
+      lcd.write(EEPROM.read((offsetTtype == 0 ? USER_CALLSIGN_DAT : WSPR_MESSAGE1) + i));
     else
       break;
   }
@@ -207,7 +233,6 @@ char byteToChar(byte srcByte){
 void updateDisplay() {
   // tks Jack Purdum W8TEE
   // replaced fsprint commmands by str commands for code size reduction
-  
   // replace code for Frequency numbering error (alignment, point...) by KD8CEC
   int i;
   unsigned long tmpFreq = frequency; //
@@ -256,6 +281,15 @@ void updateDisplay() {
       strcat(c, "B:");
   }
 
+  //Fixed by Mitani Massaru (JE4SMQ)
+  if (isShiftDisplayCWFreq == 1)
+  {
+    if (cwMode == 1)        //CWL
+        tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+    else if (cwMode == 2)   //CWU
+        tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+  }
+
   //display frequency
   for (int i = 15; i >= 6; i--) {
     if (tmpFreq > 0) {
@@ -293,22 +327,6 @@ void updateDisplay() {
     lcd.setCursor(5,diplayVFOLine);
     lcd.write(":");
   }
-
-/*
-  //now, the second line
-  memset(c, 0, sizeof(c));
-  memset(b, 0, sizeof(b));
-
-  if (inTx)
-    strcat(c, "TX ");
-  else if (ritOn)
-    strcpy(c, "RIT");
-
-  strcpy(c, "      \xff");
-  drawMeter(meter_reading);
-  strcat(c, meter);
-  strcat(c, "\xff");
-  printLine2(c);*/
 }
 
 int enc_prev_state = 3;

ubitx_20/ubitx_wspr.cpp

@@ -0,0 +1,193 @@
+/**********************************************************************************
+WSPR SENDER for uBITX  by KD8CEC
+Some of the code that sends WSPR referenced the code in G3ZIL.
+Thanks to G3ZIL for sharing great code.
+
+Due to the limited memory of uBITX, I have implemented at least only a few of the codes in uBITX.
+
+Thanks for testing
+Beta Tester : 
+
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+**********************************************************************************/
+
+#include <arduino.h>
+#include <EEPROM.h>
+#include "ubitx.h"
+
+//begin of test
+byte WsprToneCode[164];
+
+long lastTime=0;
+unsigned long TX_MSNB_P2;              // Si5351 register MSNB_P2  PLLB for Tx
+unsigned long TX_P2;    // Variable values for MSNB_P2 which defines the frequencies for the data
+
+extern int enc_read(void);
+
+byte WsprMSGCount = 0;
+#define PTT   (A3)
+
+#define WSPR_BAND1 401
+
+extern uint8_t Wspr_Reg1[8]; //3, 4, 5, 6, 7
+extern uint8_t Wspr_Reg2[8]; //2, 3, 4
+
+void SendWSPRManage()
+{
+  int knob = 0;
+  byte knobPosition = 0;
+  char isNeedDisplayInfo = 0;
+  char nowSelectedIndex = 0;
+  char nowWsprStep = 0; //0 : select Message, 1 : select band, 2 : send
+  char selectedWsprMessageIndex = -1;
+  char selectedWsprBandIndex = -1;
+
+  unsigned long WsprTXFreq = 0;
+  unsigned int WsprMultiChan = 0;
+  unsigned long prevFreq;
+  char loopIndex;
+
+  delay_background(500, 0);
+  
+  //Readed WsprMSGCount, WsprTone
+  while(1)
+  {
+    knob = enc_read();
+    
+    if (knobPosition > 0 && knob < 0)
+      knobPosition--;
+    else if (knob > 0 && (knobPosition <= (nowWsprStep == 0 ? WsprMSGCount : WSPR_BAND_COUNT) * 10 -2))
+      knobPosition++;
+
+    nowSelectedIndex = knobPosition / 10;
+
+    if (nowWsprStep == 0) //select Message status
+    {
+      printLineF2(F("WSPR:"));
+      
+      if (selectedWsprMessageIndex != nowSelectedIndex)
+      {
+        selectedWsprMessageIndex = nowSelectedIndex;
+        int wsprMessageBuffIndex = selectedWsprMessageIndex * 46;
+        
+        //Display WSPR Name tag
+        printLineFromEEPRom(0, 6, wsprMessageBuffIndex, wsprMessageBuffIndex + 4, 1); 
+
+        //Load WSPR Tonecode
+        //Read Tone Code
+        for (int i = 0; i < 41; i++)
+        {
+          byte readData = EEPROM.read(WSPR_MESSAGE1 + 5 + (wsprMessageBuffIndex) + i);  //NAME TAG 5, MESSAGE 41 = 46
+          WsprToneCode[i * 4 + 0] = readData & 3;
+          WsprToneCode[i * 4 + 1] = (readData >> 2) & 3;
+          WsprToneCode[i * 4 + 2] = (readData >> 4) & 3;
+          WsprToneCode[i * 4 + 3] = (readData >> 6) & 3;
+        }
+      }
+      else if (btnDown())
+      {
+        nowWsprStep = 1;  //Change Status to Select Band
+        knobPosition = 0;
+        nowSelectedIndex = 0;
+        delay_background(500, 0);
+      }
+    }
+    else if (nowWsprStep == 1)
+    {
+      //printLineF2(F("Select Band"));
+      if (selectedWsprBandIndex != nowSelectedIndex)
+      {
+        selectedWsprBandIndex = nowSelectedIndex;
+        int bandBuffIndex = WSPR_BAND1 + selectedWsprBandIndex * 14;
+        
+        EEPROM.get(bandBuffIndex, WsprTXFreq); 
+        EEPROM.get(bandBuffIndex + 4, WsprMultiChan); 
+
+        /*
+        //3, 4, 5, 6, 7
+        Wspr_Reg1[3] = EEPROM.read(bandBuffIndex + 6);
+        Wspr_Reg1[4] = EEPROM.read(bandBuffIndex + 7);
+        Wspr_Reg1[5] = EEPROM.read(bandBuffIndex + 8);
+        Wspr_Reg1[6] = EEPROM.read(bandBuffIndex + 9);
+        Wspr_Reg1[7] = EEPROM.read(bandBuffIndex + 10);
+        */
+        for (loopIndex = 3; loopIndex < 8; loopIndex++)
+          Wspr_Reg1[loopIndex] = EEPROM.read(bandBuffIndex + loopIndex + 3);
+
+        /*
+        Wspr_Reg2[2] = EEPROM.read(bandBuffIndex + 11);
+        Wspr_Reg2[3] = EEPROM.read(bandBuffIndex + 12);
+        Wspr_Reg2[4] = EEPROM.read(bandBuffIndex + 13);
+        */
+        //2, 3, 4
+        for (loopIndex = 2; loopIndex < 5; loopIndex++)
+          Wspr_Reg2[loopIndex] = EEPROM.read(bandBuffIndex + loopIndex + 9);
+
+        TX_MSNB_P2 = ((unsigned long)Wspr_Reg1[5] & 0x0F) << 16 | ((unsigned long)Wspr_Reg1[6]) << 8 | Wspr_Reg1[7];
+      }
+
+      ltoa(WsprTXFreq, b, DEC);
+      if (digitalRead(PTT) == 0)
+        strcpy(c, "SEND:");
+      else
+        strcpy(c, "PTT->");
+
+      strcat(c, b);
+      printLine1(c);
+      
+      if (digitalRead(PTT) == 0)
+      {
+        //printLineF1(F("Transmitting"));
+        //SEND WSPR
+        //If you need to consider the Rit and Sprite modes, uncomment them below.
+        //remark = To reduce the size of the program
+        //prevFreq = frequency;
+        //frequency = WsprTXFreq;
+        startTx(TX_CW, 0);
+        setTXFilters(WsprTXFreq);
+        
+        //Start WSPR
+        Set_WSPR_Param();
+        digitalWrite(CW_KEY, 1);     
+        
+        for (int i = 0; i < 162; i++)
+        {                                                         // Now this is the message loop
+          lastTime = millis();                                    // Store away the time when the last message symbol was sent
+          TX_P2 = TX_MSNB_P2 + WsprMultiChan * WsprToneCode[i];   // This represents the 1.46 Hz shift and is correct only for the bands specified in the array
+          TXSubFreq(TX_P2);                                       // TX at the appropriate channel frequency for....
+
+          //if (btnDown())
+          //  break;
+
+          while (millis() < lastTime + 683){}                     // .... 0,683 seconds
+        }
+        
+        digitalWrite(CW_KEY, 0);
+        stopTx(); //call setFrequency -> recovery TX Filter
+        //frequency = prevFreq;
+        
+        selectedWsprBandIndex = -1;
+      }     //end of PTT Check
+      else if (btnDown())
+      {
+        return;
+      }
+
+    }  //end of status check
+    
+    //delay_background(50, 1);
+  } //end of while
+}
+