Merge pull request #31 from phdlee/version1.073

Version1.073

ubitx_20/cat_libs.ino

@@ -278,7 +278,19 @@ void WriteEEPRom(void)  //for remove warning
   }
   else
   {
-    EEPROM.write(eepromStartIndex, write1Byte);
+    //Special Command
+    if (eepromStartIndex == 13131)  //Magic Key
+    {
+      if (write1Byte == 0x51) //Restart
+      {
+        asm volatile ("  jmp 0");
+      }
+    }
+    else
+    {
+      EEPROM.write(eepromStartIndex, write1Byte);
+    }
+    
     Serial.write(0x77); //OK  
     Serial.write(ACK);
   }
@@ -611,6 +623,34 @@ void WriteEEPRom_FT817(byte fromType)
   Serial.write(ACK);
 }
 
+const byte anlogPinIndex[6] = {A0, A1, A2, A3, A6, A7};
+
+//Read ADC Value by uBITX Manager Software
+void ReadADCValue(void)
+{
+  //ADC MAP for uBITX
+  int readedADCValue;
+  //5BYTES
+  //CAT_BUFF[0] [1] [2] [3] [4] //4 COMMAND
+  //0 READ ADDRESS
+  readedADCValue = analogRead(anlogPinIndex[CAT_BUFF[0]]);
+  CAT_BUFF[0] = readedADCValue >> 8;
+  CAT_BUFF[1] = readedADCValue;
+  SendCatData(2);
+  Serial.write(ACK);
+}
+
+void SetIFSValue(void)
+{
+  //Set IFShift Value
+  isIFShift = CAT_BUFF[0];
+  ifShiftValue = CAT_BUFF[1] + CAT_BUFF[2] * 256;
+  setFrequency(frequency);
+  SetCarrierFreq();
+  updateLine2Buffer(1); //option, perhap not need
+  Serial.write(ACK);
+}
+
 //void CatRxStatus(byte fromType) 
 void CatRxStatus(void)  //for remove warning
 {
@@ -768,6 +808,14 @@ void Check_Cat(byte fromType)
       WriteEEPRom_FT817(fromType);
       break;
 
+    case 0xDD:          //Read uBITX ADC Data
+      ReadADCValue();   //Call by uBITX Manager Program
+      break;
+
+    case 0xDE:          //IF-Shift Control by CAT
+      SetIFSValue();   //
+      break;
+
     case 0xE7 :       //Read RX Status
       CatRxStatus();
       break;

ubitx_20/cw_autokey.ino

@@ -299,13 +299,14 @@ void controlAutoCW(){
           
           printLineFromEEPRom(0, 2, cwStartIndex + displayScrolStep + CW_DATA_OFSTADJ, cwEndIndex + CW_DATA_OFSTADJ, 0); 
 
-          byte diplayAutoCWLine = 0;
-          if ((displayOption1 & 0x01) == 0x01)
-            diplayAutoCWLine = 1;
-          
-          lcd.setCursor(0, diplayAutoCWLine);
-          lcd.write(byteToChar(selectedCWTextIndex));
-          lcd.write(':');
+          //byte diplayAutoCWLine = 0;
+          //if ((displayOption1 & 0x01) == 0x01)
+          //  diplayAutoCWLine = 1;
+
+          Display_AutoKeyTextIndex(selectedCWTextIndex);
+          //lcd.setCursor(0, diplayAutoCWLine);
+          //lcd.write(byteToChar(selectedCWTextIndex));
+          //lcd.write(':');
           isNeedScroll = (cwEndIndex - cwStartIndex) > 14 ? 1 : 0;
           scrollDispayTime = millis() + scrollSpeed;
           beforeCWTextIndex = selectedCWTextIndex;

ubitx_20/ubitx.h

@@ -14,31 +14,77 @@
    You should have received a copy of the GNU General Public License
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
 **************************************************************************/
-#define WSPR_COUNT       443   //WSPR_MESSAGE_COUNT
-#define WSPR_MESSAGE1    444   //
-#define WSPR_MESSAGE2    490   //
-#define WSPR_MESSAGE3    536   //
-#define WSPR_MESSAGE4    582   //
+#include <Arduino.h>  //for Linux, On Linux it is case sensitive.
 
-#define WSPR_BAND_COUNT 3
+//==============================================================================
+// Compile Option
+//==============================================================================
+//Depending on the type of LCD mounted on the uBITX, uncomment one of the options below.
+//You must select only one.
+#define UBITX_DISPLAY_LCD1602P      //LCD mounted on unmodified uBITX
+//#define UBITX_DISPLAY_LCD1602I      //I2C type 16 x 02 LCD
+//#define UBITX_DISPLAY_LCD1602I_DUAL
+//#define UBITX_DISPLAY_LCD2004P      //24 x 04 LCD (Parallel)
+//#define UBITX_DISPLAY_LCD2004I        //I2C type 24 x 04 LCD
 
-#define TX_SSB 0
-#define TX_CW 1
+#define I2C_LCD_MASTER_ADDRESS_DEFAULT  0x3F     //0x27  //DEFAULT, if Set I2C Address by uBITX Manager, read from EEProm
+#define I2C_LCD_SECOND_ADDRESS_DEFAULT  0x27     //0x27  //only using Dual LCD Mode
 
+#define EXTEND_KEY_GROUP1           //MODE, BAND(-), BAND(+), STEP
+//#define EXTEND_KEY_GROUP2           //Numeric (0~9), Point(.), Enter  //Not supported in Version 1.0x
 
-extern void printLine1(const char *c);
-extern void printLine2(const char *c);
-extern void printLineF(char linenmbr, const __FlashStringHelper *c);
-extern void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetType);
-extern byte delay_background(unsigned delayTime, byte fromType);
-extern int btnDown(void);
-extern char c[30];
-extern char b[30];
+#define ENABLE_FACTORYALIGN
+//#define ENABLE_ADCMONITOR   //Starting with Version 1.07, you can read ADC values directly from uBITX Manager. So this function is not necessary.
 
-extern unsigned long frequency;
+extern byte I2C_LCD_MASTER_ADDRESS;        //0x27  //if Set I2C Address by uBITX Manager, read from EEProm
+extern byte I2C_LCD_SECOND_ADDRESS;         //only using Dual LCD Mode
 
-#define printLineF1(x) (printLineF(1, x))
-#define printLineF2(x) (printLineF(0, x))
+#define SMeterLatency   3  //1 is 0.25 sec
+
+#ifdef UBITX_DISPLAY_LCD1602I
+  #define USE_I2C_LCD
+#elif defined(UBITX_DISPLAY_LCD1602I_DUAL)
+  #define USE_I2C_LCD
+#elif defined(UBITX_DISPLAY_LCD2004I)
+  #define USE_I2C_LCD
+#endif
+
+//==============================================================================
+// Hardware, Define PIN Usage
+//==============================================================================
+/**
+ * We need to carefully pick assignment of pin for various purposes.
+ * There are two sets of completely programmable pins on the Raduino.
+ * First, on the top of the board, in line with the LCD connector is an 8-pin connector
+ * that is largely meant for analog inputs and front-panel control. It has a regulated 5v output,
+ * ground and six pins. Each of these six pins can be individually programmed 
+ * either as an analog input, a digital input or a digital output. 
+ * The pins are assigned as follows (left to right, display facing you): 
+ *      Pin 1 (Violet), A7, SPARE
+ *      Pin 2 (Blue),   A6, KEYER (DATA)
+ *      Pin 3 (Green), +5v 
+ *      Pin 4 (Yellow), Gnd
+ *      Pin 5 (Orange), A3, PTT
+ *      Pin 6 (Red),    A2, F BUTTON
+ *      Pin 7 (Brown),  A1, ENC B
+ *      Pin 8 (Black),  A0, ENC A
+ *Note: A5, A4 are wired to the Si5351 as I2C interface 
+ *       *     
+ * Though, this can be assigned anyway, for this application of the Arduino, we will make the following
+ * assignment
+ * A2 will connect to the PTT line, which is the usually a part of the mic connector
+ * A3 is connected to a push button that can momentarily ground this line. This will be used for RIT/Bandswitching, etc.
+ * A6 is to implement a keyer, it is reserved and not yet implemented
+ * A7 is connected to a center pin of good quality 100K or 10K linear potentiometer with the two other ends connected to
+ * ground and +5v lines available on the connector. This implments the tuning mechanism
+ */
+#define ENC_A         (A0)
+#define ENC_B         (A1)
+#define FBUTTON       (A2)
+#define PTT           (A3)
+#define ANALOG_KEYER  (A6)
+#define ANALOG_SPARE  (A7)
+#define ANALOG_SMETER (A7)  //by KD8CEC
 
 
 /** 
@@ -50,19 +96,67 @@ extern unsigned long frequency;
  *  - TX_RX line : Switches between Transmit and Receive after sensing the PTT or the morse keyer
  *  - CW_KEY line : turns on the carrier for CW
  */
+#define TX_RX         (7)   //Relay
+#define CW_TONE       (6)
+#define TX_LPF_A      (5)   //Relay
+#define TX_LPF_B      (4)   //Relay
+#define TX_LPF_C      (3)   //Relay
+#define CW_KEY        (2)
 
-#define TX_RX (7)
-#define CW_TONE (6)
-#define TX_LPF_A (5)
-#define TX_LPF_B (4)
-#define TX_LPF_C (3)
-#define CW_KEY (2)
+//==============================================================================
+// for public, Variable, functions
+//==============================================================================
+#define WSPR_BAND_COUNT 3
+#define TX_SSB          0
+#define TX_CW           1
+#define printLineF1(x) (printLineF(1, x))
+#define printLineF2(x) (printLineF(0, x))
 
-//we directly generate the CW by programmin the Si5351 to the cw tx frequency, hence, both are different modes
-//these are the parameter passed to startTx
-#define TX_SSB 0
-#define TX_CW 1
+//0x00 : None, 0x01 : MODE, 0x02:BAND+, 0x03:BAND-, 0x04:TUNE_STEP, 0x05:VFO Toggle, 0x06:SplitOn/Off, 0x07:TX/ON-OFF,  0x08:SDR Mode On / Off, 0x09:Rit Toggle
+#define FUNCTION_KEY_ADC  80  //MODE, BAND(-), BAND(+), STEP
+#define FKEY_PRESS      0x78
+#define FKEY_MODE       0x01
+#define FKEY_BANDUP     0x02
+#define FKEY_BANDDOWN   0x03
+#define FKEY_STEP       0x04
+#define FKEY_VFOCHANGE  0x05
+#define FKEY_SPLIT      0x06
+#define FKEY_TXOFF      0x07
+#define FKEY_SDRMODE    0x08
+#define FKEY_RIT        0x09
 
+#define FKEY_ENTER      0x0A
+#define FKEY_POINT      0x0B
+#define FKEY_DELETE     0x0C
+#define FKEY_CANCEL     0x0D
+
+#define FKEY_NUM0       0x10
+#define FKEY_NUM1       0x11
+#define FKEY_NUM2       0x12
+#define FKEY_NUM3       0x13
+#define FKEY_NUM4       0x14
+#define FKEY_NUM5       0x15
+#define FKEY_NUM6       0x16
+#define FKEY_NUM7       0x17
+#define FKEY_NUM8       0x18
+#define FKEY_NUM9       0x19
+
+#define FKEY_TYPE_MAX   0x1F
+
+extern unsigned long frequency;
+extern byte WsprMSGCount;
+extern byte sMeterLevels[9];
+extern byte KeyValues[16][3];    //Set : Start Value, End Value, Key Type, 16 Set (3 * 16 = 48)
+
+extern void printLine1(const char *c);
+extern void printLine2(const char *c);
+extern void printLineF(char linenmbr, const __FlashStringHelper *c);
+extern void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetType);
+extern byte delay_background(unsigned delayTime, byte fromType);
+extern int btnDown(void);
+extern char c[30];
+extern char b[30];
+extern int enc_read(void);
 extern void si5351bx_init(void);
 extern void si5351bx_setfreq(uint8_t clknum, uint32_t fout);
 extern void si5351_set_calibration(int32_t cal);
@@ -75,6 +169,6 @@ extern void stopTx(void);
 extern void setTXFilters(unsigned long freq);
 
 extern void SendWSPRManage(void);
-extern byte WsprMSGCount;
-
-
+extern char byteToChar(byte srcByte);
+extern void DisplayCallsign(byte callSignLength);
+extern void DisplayVersionInfo(const char* fwVersionInfo);

ubitx_20/ubitx_20.ino

@@ -1,8 +1,20 @@
+//Firmware Version
+//+ : This symbol identifies the firmware. 
+//    It was originally called 'CEC V1.072' but it is too long to waste the LCD window.
+//    I do not want to make this Firmware users's uBITX messy with my callsign.
+//    Putting one alphabet in front of 'v' has a different meaning.
+//    So I put + in the sense that it was improved one by one based on Original Firmware.
+//    This firmware has been gradually changed based on the original firmware created by Farhan, Jack, Jerry and others.
+
+#define FIRMWARE_VERSION_INFO F("+v1.073")  
+#define FIRMWARE_VERSION_NUM 0x02       //1st Complete Project : 1 (Version 1.061), 2st Project : 2
+
 /**
- Since KD8CEC Version 0.29, most of the original code is no longer available.
+ Cat Suppoort uBITX CEC Version
+ This firmware has been gradually changed based on the original firmware created by Farhan, Jack, Jerry and others.
  Most features(TX, Frequency Range, Ham Band, TX Control, CW delay, start Delay... more) have been added by KD8CEC.
- However, the license rules are subject to the original source rules.
- DE Ian KD8CEC
+ My wish is to keep the original author's Comment as long as the meaning does not change much, even if the code looks a bit long.
+ Ian KD8CEC
 
  Original source comment            -------------------------------------------------------------
  * This source file is under General Public License version 3.
@@ -39,177 +51,8 @@
 #include <Wire.h>
 #include <EEPROM.h>
 #include "ubitx.h"
+#include "ubitx_eemap.h"
 
-/**
-    The main chip which generates upto three oscillators of various frequencies in the
-    Raduino is the Si5351a. To learn more about Si5351a you can download the datasheet
-    from www.silabs.com although, strictly speaking it is not a requirment to understand this code.
-
-    We no longer use the standard SI5351 library because of its huge overhead due to many unused
-    features consuming a lot of program space. Instead of depending on an external library we now use
-    Jerry Gaffke's, KE7ER, lightweight standalone mimimalist "si5351bx" routines (see further down the
-    code). Here are some defines and declarations used by Jerry's routines:
-*/
-
-
-/**
- * We need to carefully pick assignment of pin for various purposes.
- * There are two sets of completely programmable pins on the Raduino.
- * First, on the top of the board, in line with the LCD connector is an 8-pin connector
- * that is largely meant for analog inputs and front-panel control. It has a regulated 5v output,
- * ground and six pins. Each of these six pins can be individually programmed 
- * either as an analog input, a digital input or a digital output. 
- * The pins are assigned as follows (left to right, display facing you): 
- *      Pin 1 (Violet), A7, SPARE
- *      Pin 2 (Blue),   A6, KEYER (DATA)
- *      Pin 3 (Green), +5v 
- *      Pin 4 (Yellow), Gnd
- *      Pin 5 (Orange), A3, PTT
- *      Pin 6 (Red),    A2, F BUTTON
- *      Pin 7 (Brown),  A1, ENC B
- *      Pin 8 (Black),  A0, ENC A
- *Note: A5, A4 are wired to the Si5351 as I2C interface 
- *       *     
- * Though, this can be assigned anyway, for this application of the Arduino, we will make the following
- * assignment
- * A2 will connect to the PTT line, which is the usually a part of the mic connector
- * A3 is connected to a push button that can momentarily ground this line. This will be used for RIT/Bandswitching, etc.
- * A6 is to implement a keyer, it is reserved and not yet implemented
- * A7 is connected to a center pin of good quality 100K or 10K linear potentiometer with the two other ends connected to
- * ground and +5v lines available on the connector. This implments the tuning mechanism
- */
-
-#define ENC_A (A0)
-#define ENC_B (A1)
-#define FBUTTON (A2)
-#define PTT   (A3)
-#define ANALOG_KEYER (A6)
-#define ANALOG_SPARE (A7)
-#define ANALOG_SMETER (A7)  //by KD8CEC
-
-/** 
- * The Raduino board is the size of a standard 16x2 LCD panel. It has three connectors:
- * 
- * First, is an 8 pin connector that provides +5v, GND and six analog input pins that can also be 
- * configured to be used as digital input or output pins. These are referred to as A0,A1,A2,
- * A3,A6 and A7 pins. The A4 and A5 pins are missing from this connector as they are used to 
- * talk to the Si5351 over I2C protocol. 
- * 
- * Second is a 16 pin LCD connector. This connector is meant specifically for the standard 16x2
- * LCD display in 4 bit mode. The 4 bit mode requires 4 data lines and two control lines to work:
- * Lines used are : RESET, ENABLE, D4, D5, D6, D7 
- * We include the library and declare the configuration of the LCD panel too
- */
-
-#include <LiquidCrystal.h>
-LiquidCrystal lcd(8,9,10,11,12,13);
-
-#define VERSION_NUM 0x01  //for KD8CEC'S firmware and for memory management software
-
-/**
- * The Arduino, unlike C/C++ on a regular computer with gigabytes of RAM, has very little memory.
- * We have to be very careful with variables that are declared inside the functions as they are 
- * created in a memory region called the stack. The stack has just a few bytes of space on the Arduino
- * if you declare large strings inside functions, they can easily exceed the capacity of the stack
- * and mess up your programs. 
- * We circumvent this by declaring a few global buffers as  kitchen counters where we can 
- * slice and dice our strings. These strings are mostly used to control the display or handle
- * the input and output from the USB port. We must keep a count of the bytes used while reading
- * the serial port as we can easily run out of buffer space. This is done in the serial_in_count variable.
- */
-char c[30], b[30];      
-char printBuff[2][17];  //mirrors what is showing on the two lines of the display
-int count = 0;          //to generally count ticks, loops, etc
-
-/** 
- *  The second set of 16 pins on the Raduino's bottom connector are have the three clock outputs and the digital lines to control the rig.
- *  This assignment is as follows :
- *    Pin   1   2    3    4    5    6    7    8    9    10   11   12   13   14   15   16
- *         GND +5V CLK0  GND  GND  CLK1 GND  GND  CLK2  GND  D2   D3   D4   D5   D6   D7  
- *  These too are flexible with what you may do with them, for the Raduino, we use them to :
- *  - TX_RX line : Switches between Transmit and Receive after sensing the PTT or the morse keyer
- *  - CW_KEY line : turns on the carrier for CW
- */
-
-#define TX_RX (7)
-#define CW_TONE (6)
-#define TX_LPF_A (5)
-#define TX_LPF_B (4)
-#define TX_LPF_C (3)
-#define CW_KEY (2)
-
-/**
- * These are the indices where these user changable settinngs are stored  in the EEPROM
- */
-#define MASTER_CAL 0
-#define LSB_CAL 4
-#define USB_CAL 8
-#define SIDE_TONE 12
-//these are ids of the vfos as well as their offset into the eeprom storage, don't change these 'magic' values
-#define VFO_A 16
-#define VFO_B 20
-#define CW_SIDETONE 24
-#define CW_SPEED 28
-
-//AT328 has 1KBytes EEPROM
-#define CW_CAL 252
-#define VFO_A_MODE 256
-#define VFO_B_MODE 257
-#define CW_DELAY 258
-#define CW_START 259
-#define HAM_BAND_COUNT 260    //
-#define TX_TUNE_TYPE 261      //
-#define HAM_BAND_RANGE 262    //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
-#define HAM_BAND_FREQS 302    //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
-  
-
-//for reduce cw key error, eeprom address
-#define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
-#define CW_ADC_ST_FROM   349   //CW ADC Range STRAIGHT KEY from (Lower 8 bit)
-#define CW_ADC_ST_TO     350   //CW ADC Range STRAIGHT KEY to   (Lower 8 bit)
-#define CW_ADC_DOT_FROM  351   //CW ADC Range DOT  from         (Lower 8 bit)
-#define CW_ADC_DOT_TO    352   //CW ADC Range DOT  to           (Lower 8 bit)
-
-#define CW_ADC_MOST_BIT2 353   //most 2bits of BOTH_TO, BOTH_FROM, DASH_TO, DASH_FROM
-#define CW_ADC_DASH_FROM 354   //CW ADC Range DASH from         (Lower 8 bit)
-#define CW_ADC_DASH_TO   355   //CW ADC Range DASH to           (Lower 8 bit)
-#define CW_ADC_BOTH_FROM 356   //CW ADC Range BOTH from         (Lower 8 bit)
-#define CW_ADC_BOTH_TO   357   //CW ADC Range BOTH to           (Lower 8 bit)
-#define CW_KEY_TYPE      358
-#define CW_DISPLAY_SHIFT 359  //Transmits on CWL, CWU Mode, LCD Frequency shifts Sidetone Frequency. 
-                              //(7:Enable / Disable //0: enable, 1:disable, (default is applied shift)
-                              //6 : 0 : Adjust Pulus, 1 : Adjust Minus
-                              //0~5: Adjust Value : * 10 = Adjust Value (0~300)
-#define COMMON_OPTION0  360  //0: Confirm : CW Frequency Shift
-                              //1 : IF Shift Save
-                              //
-                              //
-                              //
-#define IF_SHIFTVALUE   363                                
-
-#define DISPLAY_OPTION1  361   //Display Option1
-#define DISPLAY_OPTION2  362   //Display Option2
-
-#define CHANNEL_FREQ    630   //Channel 1 ~ 20, 1 Channel = 4 bytes
-#define CHANNEL_DESC    710   //Channel 1 ~ 20, 1 Channel = 4 bytes
-#define RESERVE3        770   //Reserve3 between Channel and Firmware id check
-
-//Check Firmware type and version
-#define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
-#define VERSION_ADDRESS 779   //check Firmware version
-//USER INFORMATION
-#define USER_CALLSIGN_KEY 780   //0x59
-#define USER_CALLSIGN_LEN 781   //1BYTE (OPTION + LENGTH) + CALLSIGN (MAXIMUM 18)
-#define USER_CALLSIGN_DAT 782   //CALL SIGN DATA  //direct EEPROM to LCD basic offset
-
-//AUTO KEY STRUCTURE
-//AUTO KEY USE 800 ~ 1023
-#define CW_AUTO_MAGIC_KEY 800   //0x73
-#define CW_AUTO_COUNT     801   //0 ~ 255
-#define CW_AUTO_DATA      803   //[INDEX, INDEX, INDEX,DATA,DATA, DATA (Positon offset is CW_AUTO_DATA
-#define CW_DATA_OFSTADJ   CW_AUTO_DATA - USER_CALLSIGN_DAT   //offset adjust for ditect eeprom to lcd (basic offset is USER_CALLSIGN_DAT
-#define CW_STATION_LEN    1023  //value range : 4 ~ 30
 /**
  * The uBITX is an upconnversion transceiver. The first IF is at 45 MHz.
  * The first IF frequency is not exactly at 45 Mhz but about 5 khz lower,
@@ -241,11 +84,6 @@ int count = 0;          //to generally count ticks, loops, etc
 #define LOWEST_FREQ_DIAL  (3000l)
 #define HIGHEST_FREQ_DIAL (60000000l)
 
-//we directly generate the CW by programmin the Si5351 to the cw tx frequency, hence, both are different modes
-//these are the parameter passed to startTx
-#define TX_SSB 0
-#define TX_CW 1
-
 char ritOn = 0;
 char vfoActive = VFO_A;
 int8_t meter_reading = 0; // a -1 on meter makes it invisible
@@ -332,10 +170,22 @@ unsigned long dbgCount = 0;   //not used now
 unsigned char txFilter = 0;   //which of the four transmit filters are in use
 boolean modeCalibrate = false;//this mode of menus shows extended menus to calibrate the oscillators and choose the proper
                               //beat frequency
+                              
+byte advancedFreqOption1;     //255 : Bit0: use IFTune_Value, Bit1 : use Stored enabled SDR Mode, Bit2~Bit3 : dynamic sdr frequency,  bit 7: IFTune_Value Reverse for DIY uBITX
+byte attLevel = 0;            //ATT : RF Gain Control (Receive) <-- IF1 Shift, 0 : Off, ShiftValue is attLevel * 100; attLevel 150 = 15K
+byte if1TuneValue = 0;        //0 : OFF, IF1 + if1TuneValue * 100; // + - 12500;
+byte sdrModeOn = 0;           //SDR MODE ON / OFF
+unsigned long SDR_Center_Freq; //
 
 unsigned long beforeIdle_ProcessTime = 0; //for check Idle time
 byte line2DisplayStatus = 0;  //0:Clear, 1 : menu, 1: DisplayFrom Idle, 
 char lcdMeter[17];
+byte sMeterLevels[9];
+
+byte I2C_LCD_MASTER_ADDRESS;        //0x27  //if Set I2C Address by uBITX Manager, read from EEProm
+byte I2C_LCD_SECOND_ADDRESS;         //only using Dual LCD Mode
+
+byte KeyValues[16][3];
 
 byte isIFShift = 0;     //1 = ifShift, 2 extend
 int ifShiftValue = 0;  //
@@ -347,8 +197,8 @@ int ifShiftValue = 0;  //
 
 //Ham Band
 #define MAX_LIMIT_RANGE 10  //because limited eeprom size
-byte useHamBandCount = 0;  //0 use full range frequency
-byte tuneTXType = 0;      //0 : use full range, 1 : just Change Dial speed, 2 : just ham band change, but can general band by tune, 3 : only ham band (just support 0, 2 (0.26 version))
+byte useHamBandCount = 0;   //0 use full range frequency
+byte tuneTXType = 0;        //0 : use full range, 1 : just Change Dial speed, 2 : just ham band change, but can general band by tune, 3 : only ham band (just support 0, 2 (0.26 version))
                           //100 : use full range but not TX on general band, 101 : just change dial speed but.. 2 : jut... but.. 3 : only ham band  (just support 100, 102 (0.26 version))
 unsigned int hamBandRange[MAX_LIMIT_RANGE][2];  // =  //Khz because reduce use memory
 
@@ -502,27 +352,85 @@ void setFrequency(unsigned long f){
   setTXFilters(f);
 
   unsigned long appliedCarrier = ((cwMode == 0 ? usbCarrier : cwmCarrier) + (isIFShift && (inTx == 0) ? ifShiftValue : 0));
+  int appliedTuneValue = 0;
 
-  if (cwMode == 0)
+  //applied if tune 
+  //byte advancedFreqOption1;     //255 : Bit0: use IFTune_Value, Bit1 : use Stored enabled SDR Mode, Bit2 : dynamic sdr frequency0, Bit3 : dynamic sdr frequency1, bit 7: IFTune_Value Reverse for DIY uBITX
+  if ((advancedFreqOption1 & 0x01) != 0x00)
   {
-    if (isUSB){
-      si5351bx_setfreq(2, SECOND_OSC_USB - appliedCarrier + f);
-      si5351bx_setfreq(1, SECOND_OSC_USB);
+    appliedTuneValue = if1TuneValue;
+
+    //In the LSB state, the optimum reception value was found. To apply to USB, 3Khz decrease is required.
+    if (sdrModeOn && (inTx == 0))
+      appliedTuneValue -= 15; //decrease 1.55Khz
+      
+    //if (isUSB)
+    if (cwMode == 2 || (cwMode == 0 && (isUSB)))    
+      appliedTuneValue -= 30; //decrease 3Khz
+  }
+
+   //if1Tune RX, TX Enabled, ATT : only RX Mode
+  //The IF Tune shall be measured at the LSB. Then, move the 3Khz down for USB.
+  long if1AdjustValue = ((inTx == 0) ? (attLevel * 100) : 0) + (appliedTuneValue * 100); //if1Tune RX, TX Enabled, ATT : only RX Mode  //5600
+
+  //for DIY uBITX (custom filter)
+  if ((advancedFreqOption1 & 0x80) != 0x00)  //Reverse IF Tune (- Value for DIY uBITX)
+    if1AdjustValue *= -1;
+    
+  if (sdrModeOn && (inTx == 0))  //IF SDR MODE
+  {
+    //Fixed Frequency SDR (Default Frequency : 32Mhz, available change sdr Frequency by uBITX Manager)
+    //Dynamic Frequency is for SWL without cat
+
+    //byte advancedFreqOption1;     //255 : Bit0: use IFTune_Value, Bit1 : use Stored enabled SDR Mode, Bit2 : dynamic sdr frequency0, Bit3 : dynamic sdr frequency1, bit 7: IFTune_Value Reverse for DIY uBITX
+    long moveFrequency = 0;
+    //7 6 5 4 3 2 1 0
+    //        _ _     <-- SDR Freuqncy Option
+    byte sdrOption = (advancedFreqOption1 >> 2) & 0x03;
+
+    if (sdrOption == 1) // SDR Frequency + frequenc
+    {
+      //example : offset Freq : 20 Mhz and frequency = 7.080 => 27.080 Mhz
+      //example : offset Freq : 0 Mhz and frequency = 7.080 => 7.080 Mhz
+      //for available HF, SDR
+      moveFrequency = f;
     }
-    else{
-      si5351bx_setfreq(2, SECOND_OSC_LSB + appliedCarrier + f);
-      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    else if (sdrOption == 2)  //Mhz move
+    {
+      //Offset Frequency + Mhz, 
+      //Example : Offset Frequency : 30Mhz and current Frequncy is 7.080 => 37.080Mhz
+      //          Offset Frequency : 30Mhz and current Frequncy is 14.074 => 34.074Mhz
+      moveFrequency = (f % 10000000);
     }
+    else if (sdrOption == 3)  //Khz move
+    {
+      //Offset Frequency + Khz, 
+      //Example : Offset Frequency : 30Mhz and current Frequncy is 7.080 => 30.080Mhz
+      //          Offset Frequency : 30Mhz and current Frequncy is 14.074 => 30.074Mhz
+      moveFrequency = (f % 1000000);
+    }
+
+    si5351bx_setfreq(2, 44991500 + if1AdjustValue + f);
+    si5351bx_setfreq(1, 44991500 
+      + if1AdjustValue 
+      + SDR_Center_Freq 
+      //+ ((advancedFreqOption1 & 0x04) == 0x00 ? 0 : (f % 10000000))
+      + moveFrequency
+      + 2390);
   }
   else
   {
-    if (cwMode == 1){ //CWL
-      si5351bx_setfreq(2, SECOND_OSC_LSB + appliedCarrier + f);
-      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    if (cwMode == 1 || (cwMode == 0 && (!isUSB))) //cwl or lsb
+    {
+      //CWL(cwMode == 1) or LSB (cwMode == 0 && (!isUSB))
+      si5351bx_setfreq(2, SECOND_OSC_LSB + if1AdjustValue + appliedCarrier + f);
+      si5351bx_setfreq(1, SECOND_OSC_LSB + if1AdjustValue);
     }
-    else{             //CWU
-      si5351bx_setfreq(2, SECOND_OSC_USB - appliedCarrier + f);
-      si5351bx_setfreq(1, SECOND_OSC_USB);
+    else  //cwu or usb
+    {
+      //CWU (cwMode == 2) or USB (cwMode == 0 and isUSB)
+      si5351bx_setfreq(2, SECOND_OSC_USB + if1AdjustValue - appliedCarrier + f);
+      si5351bx_setfreq(1, SECOND_OSC_USB + if1AdjustValue);
     }
   }
   
@@ -606,13 +514,6 @@ void stopTx(void){
   inTx = 0;
 
   digitalWrite(TX_RX, 0);           //turn off the tx
-
-/*
-  if (cwMode == 0)
-    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
-  else
-    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
-*/
   SetCarrierFreq();
 
   if (ritOn)
@@ -669,7 +570,7 @@ void ritDisable(){
  * flip the T/R line to T and update the display to denote transmission
  */
 
-void checkPTT(){	
+void checkPTT(){  
   //we don't check for ptt when transmitting cw
   if (cwTimeout > 0)
     return;
@@ -678,11 +579,172 @@ void checkPTT(){
     startTx(TX_SSB, 1);
     delay(50); //debounce the PTT
   }
-	
+  
   if (digitalRead(PTT) == 1 && inTx == 1)
     stopTx();
 }
+#ifdef EXTEND_KEY_GROUP1  
+void checkButton(){
+  char currentBandIndex = -1;
+  
+  //only if the button is pressed
+  int keyStatus = getBtnStatus();
+  if (keyStatus == -1)
+    return;
+    
+  delay(50);
+  keyStatus = getBtnStatus();   //will be remove 3 lines
+  if (keyStatus == -1)
+    return;
+    
+  if (keyStatus == FKEY_PRESS)  //Menu Key
+    doMenu();
+  else if (keyStatus <= FKEY_TYPE_MAX)  //EXTEND KEY GROUP #1
+  {
 
+    switch(keyStatus)
+    {
+      case FKEY_MODE :
+        if (cwMode == 1)
+        {
+          cwMode = 2;
+        }
+        else if (cwMode == 2)
+        {
+          cwMode = 0;
+          isUSB = 0;
+        }
+        else if (isUSB == 0)
+        {
+          isUSB = 1;
+        }
+        else
+        {
+          cwMode = 1;
+        }
+        break;
+      case FKEY_BANDUP :
+      case FKEY_BANDDOWN :
+        //Save Band Information
+        if (tuneTXType == 2 || tuneTXType == 3 || tuneTXType == 102 || tuneTXType == 103) { //only ham band move
+          currentBandIndex = getIndexHambanBbyFreq(frequency);
+          
+          if (currentBandIndex >= 0) {
+            saveBandFreqByIndex(frequency, modeToByte(), currentBandIndex);
+          }
+        }
+        setNextHamBandFreq(frequency, keyStatus == FKEY_BANDDOWN ? -1 : 1);  //Prior Band      
+        break;
+
+      case FKEY_STEP :
+        if (++tuneStepIndex > 5)
+          tuneStepIndex = 1;
+  
+        EEPROM.put(TUNING_STEP, tuneStepIndex);
+        printLine2ClearAndUpdate();
+        break;
+
+      case FKEY_VFOCHANGE :
+        menuVfoToggle(1); //Vfo Toggle
+        break;
+      
+      case FKEY_SPLIT :
+        menuSplitOnOff(1);
+        break;
+      case  FKEY_TXOFF:
+        menuTxOnOff(1, 0x01);
+        break;
+      case  FKEY_SDRMODE :
+         menuSDROnOff(1);
+        break;
+      case FKEY_RIT :
+        menuRitToggle(1);
+        break;
+    }
+    /*
+    if (keyStatus == FKEY_MODE) //Press Mode Key
+    {
+      if (cwMode == 1)
+      {
+        cwMode = 2;
+      }
+      else if (cwMode == 2)
+      {
+        cwMode = 0;
+        isUSB = 0;
+      }
+      else if (isUSB == 0)
+      {
+        isUSB = 1;
+      }
+      else
+      {
+        cwMode = 1;
+      }
+    }
+    else if (keyStatus == FKEY_BANDUP || keyStatus == FKEY_BANDDOWN)  //Press Mode Key
+    {
+
+      char currentBandIndex = -1;
+      
+      //Save Band Information
+      if (tuneTXType == 2 || tuneTXType == 3 || tuneTXType == 102 || tuneTXType == 103) { //only ham band move
+        currentBandIndex = getIndexHambanBbyFreq(frequency);
+        
+        if (currentBandIndex >= 0) {
+          saveBandFreqByIndex(frequency, modeToByte(), currentBandIndex);
+        }
+      }
+      
+      setNextHamBandFreq(frequency, keyStatus == FKEY_BANDDOWN ? -1 : 1);  //Prior Band      
+    }
+    else if (keyStatus == FKEY_STEP)  //FKEY_BANDUP
+    {
+      if (++tuneStepIndex > 5)
+        tuneStepIndex = 1;
+
+      EEPROM.put(TUNING_STEP, tuneStepIndex);
+      printLine2ClearAndUpdate();
+    }
+
+    else if (keyStatus == FKEY_VFOCHANGE)
+    {
+      menuVfoToggle(1); //Vfo Toggle
+    }
+    else if (keyStatus == FKEY_SPLIT)
+    {
+      menuSplitOnOff(1);
+    }
+    else if (keyStatus == FKEY_TXOFF)
+    {
+      menuTxOnOff(1, 0x01);
+    }
+    else if (keyStatus == FKEY_SDRMODE)
+    {
+      menuSDROnOff(1);
+    }
+    else if (keyStatus == FKEY_RIT)
+    {
+      menuRitToggle(1);
+    }
+    */
+      
+    FrequencyToVFO(1);
+    SetCarrierFreq();
+    setFrequency(frequency);
+    //delay_background(delayTime, 0);
+    updateDisplay();
+  }
+  
+  //wait for the button to go up again
+  while(keyStatus == getBtnStatus()) {
+    delay(10);
+    Check_Cat(0);
+  }
+  //delay(50);//debounce
+}
+
+#else
 void checkButton(){
   //only if the button is pressed
   if (!btnDown())
@@ -700,7 +762,7 @@ void checkButton(){
   }
   //delay(50);//debounce
 }
-
+#endif
 
 /************************************
 Replace function by KD8CEC
@@ -862,7 +924,7 @@ void initSettings(){
       
     printLineF(1, F("Init EEProm...")); 
       //initial all eeprom 
-    for (unsigned int i = 32; i < 1024; i++) //protect Master_cal, usb_cal
+    for (unsigned int i = 64; i < 1024; i++) //protect Master_cal, usb_cal
       EEPROM.write(i, 0);
 
     //Write Firmware ID
@@ -872,8 +934,8 @@ void initSettings(){
   }
   
   //Version Write for Memory Management Software
-  if (EEPROM.read(VERSION_ADDRESS) != VERSION_NUM)
-    EEPROM.write(VERSION_ADDRESS, VERSION_NUM);
+  if (EEPROM.read(VERSION_ADDRESS) != FIRMWARE_VERSION_NUM)
+    EEPROM.write(VERSION_ADDRESS, FIRMWARE_VERSION_NUM);
 
   EEPROM.get(CW_CAL, cwmCarrier);
 
@@ -901,12 +963,22 @@ void initSettings(){
     else
       keyerControl |= IAMBICB;
   }
-    
 
   EEPROM.get(COMMON_OPTION0, commonOption0);
   EEPROM.get(DISPLAY_OPTION1, displayOption1);
   EEPROM.get(DISPLAY_OPTION2, displayOption2);
 
+  for (byte i = 0; i < 8; i++) {
+    sMeterLevels[i + 1] = EEPROM.read(S_METER_LEVELS + i);
+  }
+
+  //KeyValues
+  for (byte i = 0; i < 16; i++) {
+    KeyValues[i][0] = EEPROM.read(EXTENDED_KEY_RANGE + (i * 3));        //RANGE : Start Value
+    KeyValues[i][1] = EEPROM.read(EXTENDED_KEY_RANGE + (i * 3) + 1);    //RANGE : End Value
+    KeyValues[i][2] = EEPROM.read(EXTENDED_KEY_RANGE + (i * 3) + 2);    //KEY TYPE 
+  }
+
   //User callsign information
   if (EEPROM.read(USER_CALLSIGN_KEY) == 0x59)
     userCallsignLength = EEPROM.read(USER_CALLSIGN_LEN);  //MAXIMUM 18 LENGTH
@@ -964,10 +1036,10 @@ void initSettings(){
   {
     //Default Setting
     arTuneStep[0] = 10;
-    arTuneStep[1] = 20;
-    arTuneStep[2] = 50;
-    arTuneStep[3] = 100;
-    arTuneStep[4] = 200;
+    arTuneStep[1] = 50;
+    arTuneStep[2] = 100;
+    arTuneStep[3] = 500;
+    arTuneStep[4] = 1000;
   }
 
   if (tuneStepIndex == 0) //New User
@@ -1015,6 +1087,25 @@ void initSettings(){
     isIFShift = ifShiftValue != 0;
   }
 
+  //Advanced Freq control
+  EEPROM.get(ADVANCED_FREQ_OPTION1, advancedFreqOption1);
+
+  //byte advancedFreqOption1;     //255 : Bit0: use IFTune_Value, Bit1 : use Stored enabled SDR Mode, Bit2 : dynamic sdr frequency0, Bit3 : dynamic sdr frequency1, bit 7: IFTune_Value Reverse for DIY uBITX
+  if ((advancedFreqOption1 & 0x01) != 0x00)
+  {
+    EEPROM.get(IF1_CAL, if1TuneValue);
+
+    //Stored Enabled SDR Mode
+    if ((advancedFreqOption1 & 0x02) != 0x00)
+    {
+      EEPROM.get(ENABLE_SDR, sdrModeOn);
+    }
+  }
+  
+  EEPROM.get(SDR_FREQUNCY, SDR_Center_Freq);
+  //if (SDR_Center_Freq == 0)
+  //  SDR_Center_Freq = 32000000;
+
   //default Value (for original hardware)
   if (cwAdcSTFrom >= cwAdcSTTo)
   {
@@ -1135,19 +1226,33 @@ void setup()
   //while(1);
   //end section of test
   */
+
+  //Load I2C LCD Address for I2C LCD 
+  //I2C LCD Parametere
+#ifdef USE_I2C_LCD  
+  EEPROM.get(I2C_LCD_MASTER, I2C_LCD_MASTER_ADDRESS);
+  EEPROM.get(I2C_LCD_SECOND, I2C_LCD_SECOND_ADDRESS);
+
+  if (I2C_LCD_MASTER_ADDRESS < 0x10 || I2C_LCD_MASTER_ADDRESS > 0xF0)
+    I2C_LCD_MASTER_ADDRESS = I2C_LCD_MASTER_ADDRESS_DEFAULT;
+    
+  if (I2C_LCD_SECOND_ADDRESS < 0x10 || I2C_LCD_SECOND_ADDRESS > 0xF0)
+    I2C_LCD_SECOND_ADDRESS = I2C_LCD_SECOND_ADDRESS_DEFAULT;
+#endif  
   
   //Serial.begin(9600);
-  lcd.begin(16, 2);
-  printLineF(1, F("CE v1.061")); 
+  LCD_Init();
+  //printLineF(1, FIRMWARE_VERSION_INFO);
+  DisplayVersionInfo(FIRMWARE_VERSION_INFO);
 
   Init_Cat(38400, SERIAL_8N1);
-  initMeter(); //not used in this build
   initSettings();
 
   if (userCallsignLength > 0 && ((userCallsignLength & 0x80) == 0x80)) {
     userCallsignLength = userCallsignLength & 0x7F;
-    printLineFromEEPRom(0, 0, 0, userCallsignLength -1, 0); //eeprom to lcd use offset (USER_CALLSIGN_DAT)
-    delay(500);
+    //printLineFromEEPRom(0, 0, 0, userCallsignLength -1, 0); //eeprom to lcd use offset (USER_CALLSIGN_DAT)
+    //delay(500);
+    DisplayCallsign(userCallsignLength);
   }
   else {
     printLineF(0, F("uBITX v0.20")); 
@@ -1165,8 +1270,10 @@ void setup()
   setFrequency(vfoA);
   updateDisplay();
 
+#ifdef ENABLE_FACTORYALIGN
   if (btnDown())
     factory_alignment();
+#endif
 }
 
 //Auto save Frequency and Mode with Protected eeprom life by KD8CEC

ubitx_20/ubitx_eemap.h

@@ -0,0 +1,127 @@
+/*************************************************************************
+  header file for EEProm Address Map by KD8CEC
+  It must be protected to protect the factory calibrated calibration.
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+**************************************************************************/
+//==============================================================================
+// Factory-shipped EEProm address
+// (factory Firmware)
+// Address : 0 ~ 31
+//==============================================================================
+#define MASTER_CAL            0
+#define LSB_CAL               4
+#define USB_CAL               8
+#define SIDE_TONE             12
+//these are ids of the vfos as well as their offset into the eeprom storage, don't change these 'magic' values
+#define VFO_A                 16
+#define VFO_B                 20
+#define CW_SIDETONE           24
+#define CW_SPEED              28
+
+//==============================================================================
+// The spare space available in the original firmware #1
+// Address : 32 ~ 63
+//==============================================================================
+#define RESERVE_FOR_FACTORY1  32
+
+//==============================================================================
+// The spare space available in the original firmware #2
+// (Enabled if the EEProm address is insufficient)
+// Address : 64 ~ 100
+//==============================================================================
+#define RESERVE_FOR_FACTORY2  64
+
+//==============================================================================
+// KD8CEC EEPROM MAP
+// Address : 101 ~ 1023
+// 256 is the base address
+// 256 ~ 1023 (EEProm Section #1)
+// 255 ~ 101  (EEProm Section #2)
+//==============================================================================
+
+//0x00 : None, 0x01 : MODE, 0x02:BAND+, 0x03:BAND-, 0x04:TUNE_STEP, 0x05:VFO Toggle, 0x06:SplitOn/Off, 0x07:TX/ON-OFF,  0x08:SDR Mode On / Off, 0x09:Rit Toggle
+#define EXTENDED_KEY_RANGE    140 //Extended Key => Set : Start Value, End Value, Key Type, 16 Set (3 * 16 = 48)
+
+#define I2C_LCD_MASTER        190
+#define I2C_LCD_SECOND        191
+
+#define S_METER_LEVELS        230 //LEVEL0 ~ LEVEL7
+
+#define ADVANCED_FREQ_OPTION1 240 //Bit0: use IFTune_Value, Bit1 : use Stored enabled SDR Mode, Bit2 : dynamic sdr frequency
+#define IF1_CAL               241
+#define ENABLE_SDR            242
+#define SDR_FREQUNCY          243
+#define CW_CAL                252
+
+#define VFO_A_MODE            256
+#define VFO_B_MODE            257
+#define CW_DELAY              258
+#define CW_START              259
+#define HAM_BAND_COUNT        260    //
+#define TX_TUNE_TYPE          261      //
+#define HAM_BAND_RANGE        262    //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
+#define HAM_BAND_FREQS        302    //40, 1 BAND = 4Byte most bit is mode
+#define TUNING_STEP           342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+
+//for reduce cw key error, eeprom address
+#define CW_ADC_MOST_BIT1      348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
+#define CW_ADC_ST_FROM        349   //CW ADC Range STRAIGHT KEY from (Lower 8 bit)
+#define CW_ADC_ST_TO          350   //CW ADC Range STRAIGHT KEY to   (Lower 8 bit)
+#define CW_ADC_DOT_FROM       351   //CW ADC Range DOT  from         (Lower 8 bit)
+#define CW_ADC_DOT_TO         352   //CW ADC Range DOT  to           (Lower 8 bit)
+
+#define CW_ADC_MOST_BIT2      353   //most 2bits of BOTH_TO, BOTH_FROM, DASH_TO, DASH_FROM
+#define CW_ADC_DASH_FROM      354   //CW ADC Range DASH from         (Lower 8 bit)
+#define CW_ADC_DASH_TO        355   //CW ADC Range DASH to           (Lower 8 bit)
+#define CW_ADC_BOTH_FROM      356   //CW ADC Range BOTH from         (Lower 8 bit)
+#define CW_ADC_BOTH_TO        357   //CW ADC Range BOTH to           (Lower 8 bit)
+#define CW_KEY_TYPE           358
+#define CW_DISPLAY_SHIFT      359   //Transmits on CWL, CWU Mode, LCD Frequency shifts Sidetone Frequency. 
+                                    //(7:Enable / Disable //0: enable, 1:disable, (default is applied shift)
+                                    //6 : 0 : Adjust Pulus, 1 : Adjust Minus
+                                    //0~5: Adjust Value : * 10 = Adjust Value (0~300)
+#define COMMON_OPTION0        360   //0: Confirm : CW Frequency Shift
+                                    //1 : IF Shift Save
+#define IF_SHIFTVALUE         363
+
+#define DISPLAY_OPTION1       361   //Display Option1
+#define DISPLAY_OPTION2       362   //Display Option2
+
+#define WSPR_COUNT            443   //WSPR_MESSAGE_COUNT
+#define WSPR_MESSAGE1         444   //
+#define WSPR_MESSAGE2         490   //
+#define WSPR_MESSAGE3         536   //
+#define WSPR_MESSAGE4         582   //
+
+#define CHANNEL_FREQ          630   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define CHANNEL_DESC          710   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define RESERVE3              770   //Reserve3 between Channel and Firmware id check
+
+//Check Firmware type and version
+#define FIRMWAR_ID_ADDR       776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
+#define VERSION_ADDRESS       779   //check Firmware version
+//USER INFORMATION
+#define USER_CALLSIGN_KEY     780   //0x59
+#define USER_CALLSIGN_LEN     781   //1BYTE (OPTION + LENGTH) + CALLSIGN (MAXIMUM 18)
+#define USER_CALLSIGN_DAT     782   //CALL SIGN DATA  //direct EEPROM to LCD basic offset
+
+//AUTO KEY STRUCTURE
+//AUTO KEY USE 800 ~ 1023
+#define CW_AUTO_MAGIC_KEY     800   //0x73
+#define CW_AUTO_COUNT         801   //0 ~ 255
+#define CW_AUTO_DATA          803   //[INDEX, INDEX, INDEX,DATA,DATA, DATA (Positon offset is CW_AUTO_DATA
+#define CW_DATA_OFSTADJ       CW_AUTO_DATA - USER_CALLSIGN_DAT   //offset adjust for ditect eeprom to lcd (basic offset is USER_CALLSIGN_DAT
+#define CW_STATION_LEN        1023  //value range : 4 ~ 30
+

ubitx_20/ubitx_idle.ino

@@ -1,254 +0,0 @@
-/*************************************************************************
-  KD8CEC's uBITX Idle time Processing
-  Functions that run at times that do not affect TX, CW, and CAT
-  It is called in 1/10 time unit.
------------------------------------------------------------------------------
-   This program is free software: you can redistribute it and/or modify
-   it under the terms of the GNU General Public License as published by
-   the Free Software Foundation, either version 3 of the License, or
-   (at your option) any later version.
-
-   This program is distributed in the hope that it will be useful,
-   but WITHOUT ANY WARRANTY; without even the implied warranty of
-   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-   GNU General Public License for more details.
-
-   You should have received a copy of the GNU General Public License
-   along with this program.  If not, see <http://www.gnu.org/licenses/>.
-
-**************************************************************************/
-char line2Buffer[16];
-//KD8CEC 200Hz ST
-//L14.150 200Hz ST
-//U14.150 +150khz
-int freqScrollPosition = 0;
-//Example Line2 Optinal Display
-//immediate execution, not call by scheulder
-void updateLine2Buffer(char isDirectCall)
-{
-  unsigned long tmpFreq = 0;
-  if (isDirectCall == 0)
-  {
-    if (ritOn)
-    {
-      strcpy(line2Buffer, "RitTX:");
-  
-      //display frequency
-      tmpFreq = ritTxFrequency;
-      for (int i = 15; i >= 6; i--) {
-        if (tmpFreq > 0) {
-          if (i == 12 || i == 8) line2Buffer[i] = '.';
-          else {
-            line2Buffer[i] = tmpFreq % 10 + 0x30;
-            tmpFreq /= 10;
-          }
-        }
-        else
-          line2Buffer[i] = ' ';
-      }
-  
-      return;
-    } //end of ritOn display
-
-    //======================================================
-    //other VFO display
-    //======================================================
-    if (vfoActive == VFO_B)
-    {
-      tmpFreq = vfoA;
-    }
-    else 
-    {
-      tmpFreq = vfoB;
-    }
-  
-    // EXAMPLE 1 & 2
-    //U14.150.100
-    //display frequency
-    for (int i = 9; i >= 0; i--) {
-      if (tmpFreq > 0) {
-        if (i == 2 || i == 6) line2Buffer[i] = '.';
-        else {
-          line2Buffer[i] = tmpFreq % 10 + 0x30;
-          tmpFreq /= 10;
-        }
-      }
-      else
-        line2Buffer[i] = ' ';
-    }
-  
-    //EXAMPLE #1
-    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
-      line2Buffer[6] = 'k';
-    else
-    {
-      //example #2
-      if (freqScrollPosition++ > 18)    //none scroll display time
-      {
-        line2Buffer[6] = 'k';
-        if (freqScrollPosition > 25)
-          freqScrollPosition = -1;
-      }
-      else                              //scroll frequency 
-      {
-        line2Buffer[10] = 'H';
-        line2Buffer[11] = 'z';
-    
-        if (freqScrollPosition < 7)   
-        {
-          for (int i = 11; i >= 0; i--)
-            if (i - (7 - freqScrollPosition) >= 0)
-              line2Buffer[i] = line2Buffer[i - (7 - freqScrollPosition)];
-            else
-              line2Buffer[i] = ' ';
-        }
-        else
-        {
-          for (int i = 0; i < 11; i++)
-            if (i + (freqScrollPosition - 7) <= 11)
-              line2Buffer[i] = line2Buffer[i + (freqScrollPosition - 7)];
-            else
-              line2Buffer[i] = ' ';
-        }
-      }
-    } //scroll
-    
-    line2Buffer[7] = ' ';
-  } //check direct call by encoder
-  
-  if (isIFShift)
-  {
-    if (isDirectCall == 1)
-      for (int i = 0; i < 16; i++)
-        line2Buffer[i] = ' ';
-      
-      //IFShift Offset Value 
-    line2Buffer[8] = 'I';
-    line2Buffer[9] = 'F';
-
-    //if (ifShiftValue == 0)
-    //{
-      /*
-      line2Buffer[10] = 'S';
-      line2Buffer[11] = ':';
-      line2Buffer[12] = 'O';
-      line2Buffer[13] = 'F';
-      line2Buffer[14] = 'F';
-      */
-    //}
-    //else
-    //{
-      line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
-      line2Buffer[11] = 0;
-      line2Buffer[12] = ' ';
-    
-      //11, 12, 13, 14, 15
-      memset(b, 0, sizeof(b));
-      ltoa(ifShiftValue, b, DEC);
-      strncat(line2Buffer, b, 5);
-    //}
-    
-    if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
-        printLine2(line2Buffer);    
-  }       // end of display IF
-  else    // step display
-  {
-    if (isDirectCall != 0)
-      return;
-
-    memset(&line2Buffer[8], ' ', 8);
-    //Step
-    long tmpStep = arTuneStep[tuneStepIndex -1];
-    
-    byte isStepKhz = 0;
-    if (tmpStep >= 1000)
-    {
-      isStepKhz = 2;
-    }
-      
-    for (int i = 10; i >= 8 - isStepKhz; i--) {
-      if (tmpStep > 0) {
-          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
-          tmpStep /= 10;
-      }
-      else
-        line2Buffer[i +isStepKhz] = ' ';
-    }
-    //if (isStepKhz == 1)
-    //  line2Buffer[10] = 'k';
-
-    if (isStepKhz == 0)
-    {
-      line2Buffer[11] = 'H';
-      line2Buffer[12] = 'z';
-    }
-  
-    line2Buffer[13] = ' ';
-    //if (
-    //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
-    if (cwKeyType == 0)
-    {
-      line2Buffer[14] = 'S';
-      line2Buffer[15] = 'T';
-    }
-    else if (cwKeyType == 1)
-    {
-      line2Buffer[14] = 'I';
-      line2Buffer[15] = 'A';
-    }
-    else
-    {
-      line2Buffer[14] = 'I';
-      line2Buffer[15] = 'B';
-    }    
-  }
-  
-}
-
-//meterType : 0 = S.Meter, 1 : P.Meter
-void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
-{
-  if (meterType == 0 || meterType == 1 || meterType == 2)
-  {
-    drawMeter(meterValue);  //call original source code
-    int lineNumber = 0;
-    if ((displayOption1 & 0x01) == 0x01)
-      lineNumber = 1;
-    
-    lcd.setCursor(drawPosition, lineNumber);
-  
-    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
-      lcd.write(lcdMeter[i]);
-  }
-}
-
-byte testValue = 0;
-char checkCount = 0;
-void idle_process()
-{
-  //space for user graphic display
-  if (menuOn == 0)
-  {
-    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
-      return;
-      
-    //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
-    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
-      if (checkCount++ > 1)
-      {
-        updateLine2Buffer(0); //call by scheduler
-        printLine2(line2Buffer);
-        line2DisplayStatus = 2;
-        checkCount = 0;
-      }
-
-      //EX for Meters
-      /*
-      DisplayMeter(0, testValue++, 7);
-      if (testValue > 30)
-        testValue = 0;
-      */
-    }
-  }
-}
-

ubitx_20/ubitx_lcd_1602.ino

@@ -0,0 +1,840 @@
+/*************************************************************************
+  KD8CEC's uBITX Display Routine for LCD1602 Parrel
+  1.This is the display code for the default LCD mounted in uBITX.
+  2.Display related functions of uBITX.  Some functions moved from uBITX_Ui.
+  3.uBITX Idle time Processing
+    Functions that run at times that do not affect TX, CW, and CAT
+    It is called in 1/10 time unit.
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+**************************************************************************/
+#include "ubitx.h"
+
+//Common Defines *********************************************************
+#define LCD_CLEARDISPLAY 0x01
+#define LCD_RETURNHOME 0x02
+#define LCD_ENTRYMODESET 0x04
+#define LCD_DISPLAYCONTROL 0x08
+#define LCD_CURSORSHIFT 0x10
+#define LCD_FUNCTIONSET 0x20
+#define LCD_SETCGRAMADDR 0x40
+#define LCD_SETDDRAMADDR 0x80
+
+// flags for display entry mode
+#define LCD_ENTRYRIGHT 0x00
+#define LCD_ENTRYLEFT 0x02
+#define LCD_ENTRYSHIFTINCREMENT 0x01
+#define LCD_ENTRYSHIFTDECREMENT 0x00
+
+// flags for display on/off control
+#define LCD_DISPLAYON 0x04
+#define LCD_DISPLAYOFF 0x00
+#define LCD_CURSORON 0x02
+#define LCD_CURSOROFF 0x00
+#define LCD_BLINKON 0x01
+#define LCD_BLINKOFF 0x00
+
+// flags for display/cursor shift
+#define LCD_DISPLAYMOVE 0x08
+#define LCD_CURSORMOVE 0x00
+#define LCD_MOVERIGHT 0x04
+#define LCD_MOVELEFT 0x00
+
+// flags for function set
+#define LCD_8BITMODE 0x10
+#define LCD_4BITMODE 0x00
+#define LCD_2LINE 0x08
+#define LCD_1LINE 0x00
+#define LCD_5x10DOTS 0x04
+#define LCD_5x8DOTS 0x00
+
+// flags for backlight control
+#define LCD_BACKLIGHT 0x08
+#define LCD_NOBACKLIGHT 0x00
+
+//========================================================================
+//Begin of TinyLCD Library by KD8CEC
+//========================================================================
+
+#ifdef UBITX_DISPLAY_LCD1602P
+/*************************************************************************
+  LCD1602_TINY Library for 16 x 2 LCD
+  Referecnce Source : LiquidCrystal.cpp 
+  KD8CEC
+
+  This source code is modified version for small program memory 
+  from Arduino LiquidCrystal Library
+
+  I wrote this code myself, so there is no license restriction. 
+  So this code allows anyone to write with confidence.
+  But keep it as long as the original author of the code.
+  DE Ian KD8CEC
+**************************************************************************/
+
+#define LCD_Command(x)  (LCD_Send(x, LOW))
+#define LCD_Write(x)    (LCD_Send(x, HIGH))
+
+#define UBITX_DISPLAY_LCD1602_BASE
+
+//Define  connected PIN
+#define LCD_PIN_RS 8
+#define LCD_PIN_EN 9
+uint8_t LCD_PIN_DAT[4] = {10, 11, 12, 13};
+
+void write4bits(uint8_t value) 
+{
+  for (int i = 0; i < 4; i++) 
+    digitalWrite(LCD_PIN_DAT[i], (value >> i) & 0x01);
+
+  digitalWrite(LCD_PIN_EN, LOW);
+  delayMicroseconds(1);    
+  digitalWrite(LCD_PIN_EN, HIGH);
+  delayMicroseconds(1);    // enable pulse must be >450ns
+  digitalWrite(LCD_PIN_EN, LOW);
+  delayMicroseconds(100);   // commands need > 37us to settle
+}
+
+void LCD_Send(uint8_t value, uint8_t mode)
+{
+    digitalWrite(LCD_PIN_RS, mode);
+    write4bits(value>>4);
+    write4bits(value);
+}
+
+void LCD1602_Init()
+{
+  pinMode(LCD_PIN_RS, OUTPUT);
+  pinMode(LCD_PIN_EN, OUTPUT);
+  for (int i = 0; i < 4; i++)
+    pinMode(LCD_PIN_DAT[i], OUTPUT);
+
+  delayMicroseconds(50); 
+ 
+  // Now we pull both RS and R/W low to begin commands
+  digitalWrite(LCD_PIN_RS, LOW);
+  digitalWrite(LCD_PIN_EN, LOW);
+
+  // we start in 8bit mode, try to set 4 bit mode
+  write4bits(0x03);
+  delayMicroseconds(4500); // wait min 4.1ms
+  
+  // second try
+  write4bits(0x03);
+  delayMicroseconds(4500); // wait min 4.1ms
+  
+  // third go!
+  write4bits(0x03); 
+  delayMicroseconds(150);
+  
+  // finally, set to 4-bit interface
+  write4bits(0x02);
+
+  // finally, set # lines, font size, etc.
+  LCD_Command(LCD_FUNCTIONSET | LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS | LCD_2LINE);  
+
+  // turn the display on with no cursor or blinking default
+  LCD_Command(LCD_DISPLAYCONTROL | LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF);
+
+  // clear it off
+  LCD_Command(LCD_CLEARDISPLAY);  // clear display, set cursor position to zero
+  delayMicroseconds(2000);  // this command takes a long time!
+
+  LCD_Command(LCD_ENTRYMODESET | LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT);
+}
+
+#endif
+//========================================================================
+//End of TinyLCD Library by KD8CEC
+//========================================================================
+
+
+//========================================================================
+//Begin of I2CTinyLCD Library by KD8CEC
+//========================================================================
+#ifdef UBITX_DISPLAY_LCD1602I
+#include <Wire.h>
+/*************************************************************************
+  I2C Tiny LCD Library
+  Referecnce Source : LiquidCrystal_I2C.cpp // Based on the work by DFRobot
+  KD8CEC
+
+  This source code is modified version for small program memory 
+  from Arduino LiquidCrystal_I2C Library
+
+  I wrote this code myself, so there is no license restriction. 
+  So this code allows anyone to write with confidence.
+  But keep it as long as the original author of the code.
+  Ian KD8CEC
+**************************************************************************/
+#define UBITX_DISPLAY_LCD1602_BASE
+
+#define En B00000100  // Enable bit
+#define Rw B00000010  // Read/Write bit
+#define Rs B00000001  // Register select bit
+
+#define LCD_Command(x)  (LCD_Send(x, 0))
+#define LCD_Write(x)    (LCD_Send(x, Rs))
+
+uint8_t _Addr;
+uint8_t _displayfunction;
+uint8_t _displaycontrol;
+uint8_t _displaymode;
+uint8_t _numlines;
+uint8_t _cols;
+uint8_t _rows;
+uint8_t _backlightval;
+
+#define printIIC(args)  Wire.write(args)
+
+void expanderWrite(uint8_t _data)
+{
+  Wire.beginTransmission(_Addr);
+  printIIC((int)(_data) | _backlightval);
+  Wire.endTransmission();   
+}
+
+void pulseEnable(uint8_t _data){
+  expanderWrite(_data | En);  // En high
+  delayMicroseconds(1);       // enable pulse must be >450ns
+  
+  expanderWrite(_data & ~En); // En low
+  delayMicroseconds(50);      // commands need > 37us to settle
+}
+
+void write4bits(uint8_t value) 
+{
+  expanderWrite(value);
+  pulseEnable(value);
+}
+
+void LCD_Send(uint8_t value, uint8_t mode)
+{
+  uint8_t highnib=value&0xf0;
+  uint8_t lownib=(value<<4)&0xf0;
+       write4bits((highnib)|mode);
+  write4bits((lownib)|mode); 
+}
+
+
+// Turn the (optional) backlight off/on
+void noBacklight(void) {
+  _backlightval=LCD_NOBACKLIGHT;
+  expanderWrite(0);
+}
+
+void backlight(void) {
+  _backlightval=LCD_BACKLIGHT;
+  expanderWrite(0);
+}
+
+void LCD1602_Init()
+{
+  //I2C Init
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+  _cols = 16;
+  _rows = 2;
+  _backlightval = LCD_NOBACKLIGHT;
+  Wire.begin();
+
+  delay(50);
+  
+  // Now we pull both RS and R/W low to begin commands
+  expanderWrite(_backlightval); // reset expanderand turn backlight off (Bit 8 =1)
+  delay(1000);
+      //put the LCD into 4 bit mode
+  // this is according to the hitachi HD44780 datasheet
+  // figure 24, pg 46
+  
+    // we start in 8bit mode, try to set 4 bit mode
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // second try
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // third go!
+   write4bits(0x03 << 4); 
+   delayMicroseconds(150);
+   
+   // finally, set to 4-bit interface
+   write4bits(0x02 << 4); 
+
+  // finally, set # lines, font size, etc.
+  LCD_Command(LCD_FUNCTIONSET | LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS | LCD_2LINE);  
+
+  // turn the display on with no cursor or blinking default
+  LCD_Command(LCD_DISPLAYCONTROL | LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF);
+
+  // clear it off
+  LCD_Command(LCD_CLEARDISPLAY);  // clear display, set cursor position to zero
+  //delayMicroseconds(2000);  // this command takes a long time!
+  delayMicroseconds(1000);  // this command takes a long time!
+
+  LCD_Command(LCD_ENTRYMODESET | LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT);
+
+  backlight();
+}
+
+/*
+void LCD_Print(const char *c) 
+{
+  for (uint8_t i = 0; i < strlen(c); i++)
+  {
+    if (*(c + i) == 0x00) return;
+    LCD_Write(*(c + i));
+  }
+}
+
+void LCD_SetCursor(uint8_t col, uint8_t row)
+{
+  LCD_Command(LCD_SETDDRAMADDR | (col + row * 0x40));  //0 : 0x00, 1 : 0x40, only for 16 x 2 lcd
+}
+
+void LCD_CreateChar(uint8_t location, uint8_t charmap[]) 
+{
+  location &= 0x7; // we only have 8 locations 0-7
+  LCD_Command(LCD_SETCGRAMADDR | (location << 3));
+  for (int i=0; i<8; i++)
+    LCD_Write(charmap[i]);
+}
+*/
+#endif
+//========================================================================
+//End of I2CTinyLCD Library by KD8CEC
+//========================================================================
+
+
+//========================================================================
+// 16 X 02 LCD Routines
+//Begin of Display Base Routines (Init, printLine..)
+//========================================================================
+#ifdef UBITX_DISPLAY_LCD1602_BASE
+
+//SWR GRAPH,  DrawMeter and drawingMeter Logic function by VK2ETA 
+#define OPTION_SKINNYBARS
+
+char c[30], b[30];
+char printBuff[2][17];  //mirrors what is showing on the two lines of the display
+
+
+void LCD_Print(const char *c) 
+{
+  for (uint8_t i = 0; i < strlen(c); i++)
+  {
+    if (*(c + i) == 0x00) return;
+    LCD_Write(*(c + i));
+  }
+}
+
+void LCD_SetCursor(uint8_t col, uint8_t row)
+{
+  LCD_Command(LCD_SETDDRAMADDR | (col + row * 0x40));  //0 : 0x00, 1 : 0x40, only for 16 x 2 lcd
+}
+
+void LCD_CreateChar(uint8_t location, uint8_t charmap[]) 
+{
+  location &= 0x7; // we only have 8 locations 0-7
+  LCD_Command(LCD_SETCGRAMADDR | (location << 3));
+  for (int i=0; i<8; i++)
+    LCD_Write(charmap[i]);
+}
+
+void LCD_Init(void)
+{
+  LCD1602_Init();  
+  initMeter(); //for Meter Display
+}
+
+// The generic routine to display one line on the LCD 
+void printLine(unsigned char linenmbr, const char *c) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  if (strcmp(c, printBuff[linenmbr])) {     // only refresh the display when there was a change
+    LCD_SetCursor(0, linenmbr);             // place the cursor at the beginning of the selected line
+    LCD_Print(c);
+    strcpy(printBuff[linenmbr], c);
+
+    for (byte i = strlen(c); i < 16; i++) { // add white spaces until the end of the 16 characters line is reached
+      LCD_Write(' ');
+    }
+  }
+}
+
+void printLineF(char linenmbr, const __FlashStringHelper *c)
+{
+  int i;
+  char tmpBuff[17];
+  PGM_P p = reinterpret_cast<PGM_P>(c);  
+
+  for (i = 0; i < 17; i++){
+    unsigned char fChar = pgm_read_byte(p++);
+    tmpBuff[i] = fChar;
+    if (fChar == 0)
+      break;
+  }
+
+  printLine(linenmbr, tmpBuff);
+}
+
+#define LCD_MAX_COLUMN 16
+void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetTtype) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  
+  LCD_SetCursor(lcdColumn, linenmbr);
+
+  for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
+  {
+    if (++lcdColumn <= LCD_MAX_COLUMN)
+      LCD_Write(EEPROM.read((offsetTtype == 0 ? USER_CALLSIGN_DAT : WSPR_MESSAGE1) + i));
+    else
+      break;
+  }
+  
+  for (byte i = lcdColumn; i < 16; i++) //Right Padding by Space
+      LCD_Write(' ');
+}
+
+//  short cut to print to the first line
+void printLine1(const char *c)
+{
+  printLine(1,c);
+}
+//  short cut to print to the first line
+void printLine2(const char *c)
+{
+  printLine(0,c);
+}
+
+void clearLine2()
+{
+  printLine2("");
+  line2DisplayStatus = 0;
+}
+
+//  short cut to print to the first line
+void printLine1Clear(){
+  printLine(1,"");
+}
+//  short cut to print to the first line
+void printLine2Clear(){
+  printLine(0, "");
+}
+
+void printLine2ClearAndUpdate(){
+  printLine(0, "");
+  line2DisplayStatus = 0;  
+  updateDisplay();
+}
+
+//==================================================================================
+//End of Display Base Routines
+//==================================================================================
+
+
+//==================================================================================
+//Begin of User Interface Routines
+//==================================================================================
+
+//Main Display
+// this builds up the top line of the display with frequency and mode
+void updateDisplay() {
+  // tks Jack Purdum W8TEE
+  // replaced fsprint commmands by str commands for code size reduction
+  // replace code for Frequency numbering error (alignment, point...) by KD8CEC
+  int i;
+  unsigned long tmpFreq = frequency; //
+  
+  memset(c, 0, sizeof(c));
+
+  if (inTx){
+    if (isCWAutoMode == 2) {
+      for (i = 0; i < 4; i++)
+        c[3-i] = (i < autoCWSendReservCount ? byteToChar(autoCWSendReserv[i]) : ' ');
+
+      //display Sending Index
+      c[4] = byteToChar(sendingCWTextIndex);
+      c[5] = '=';
+    }
+    else {
+      if (cwTimeout > 0)
+        strcpy(c, "   CW:");
+      else
+        strcpy(c, "   TX:");
+    }
+  }
+  else {
+    if (ritOn)
+      strcpy(c, "RIT ");
+    else {
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          strcpy(c, "USB ");
+        else
+          strcpy(c, "LSB ");
+      }
+      else if (cwMode == 1)
+      {
+          strcpy(c, "CWL ");
+      }
+      else
+      {
+          strcpy(c, "CWU ");
+      }
+    }
+    if (vfoActive == VFO_A) // VFO A is active
+      strcat(c, "A:");
+    else
+      strcat(c, "B:");
+  }
+
+  //Fixed by Mitani Massaru (JE4SMQ)
+  if (isShiftDisplayCWFreq == 1)
+  {
+    if (cwMode == 1)        //CWL
+        tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+    else if (cwMode == 2)   //CWU
+        tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+  }
+
+  //display frequency
+  for (int i = 15; i >= 6; i--) {
+    if (tmpFreq > 0) {
+      if (i == 12 || i == 8) c[i] = '.';
+      else {
+        c[i] = tmpFreq % 10 + 0x30;
+        tmpFreq /= 10;
+      }
+    }
+    else
+      c[i] = ' ';
+  }
+
+  //remarked by KD8CEC
+  //already RX/TX status display, and over index (16 x 2 LCD)
+  //if (inTx)
+  //  strcat(c, " TX");
+  printLine(1, c);
+
+  byte diplayVFOLine = 1;
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayVFOLine = 0;
+
+  if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
+    (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02))) {
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write((uint8_t)0);
+  }
+  else if (isCWAutoMode == 2){
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write(0x7E);
+  }
+  else
+  {
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write(':');
+  }
+}
+
+
+
+char line2Buffer[17];
+//KD8CEC 200Hz ST
+//L14.150 200Hz ST
+//U14.150 +150khz
+int freqScrollPosition = 0;
+
+//Example Line2 Optinal Display
+//immediate execution, not call by scheulder
+//warning : unused parameter 'displayType' <-- ignore, this is reserve
+void updateLine2Buffer(char displayType)
+{
+  unsigned long tmpFreq = 0;
+  if (ritOn)
+  {
+    strcpy(line2Buffer, "RitTX:");
+
+    //display frequency
+    tmpFreq = ritTxFrequency;
+
+    //Fixed by Mitani Massaru (JE4SMQ)
+    if (isShiftDisplayCWFreq == 1)
+    {
+      if (cwMode == 1)        //CWL
+          tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+      else if (cwMode == 2)   //CWU
+          tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+    }
+    
+    for (int i = 15; i >= 6; i--) {
+      if (tmpFreq > 0) {
+        if (i == 12 || i == 8) line2Buffer[i] = '.';
+        else {
+          line2Buffer[i] = tmpFreq % 10 + 0x30;
+          tmpFreq /= 10;
+        }
+      }
+      else
+        line2Buffer[i] = ' ';
+    }
+
+    return;
+  } //end of ritOn display
+
+  //other VFO display
+  if (vfoActive == VFO_B)
+  {
+    tmpFreq = vfoA;
+  }
+  else 
+  {
+    tmpFreq = vfoB;
+  }
+
+  // EXAMPLE 1 & 2
+  //U14.150.100
+  //display frequency
+  for (int i = 9; i >= 0; i--) {
+    if (tmpFreq > 0) {
+      if (i == 2 || i == 6) line2Buffer[i] = '.';
+      else {
+        line2Buffer[i] = tmpFreq % 10 + 0x30;
+        tmpFreq /= 10;
+      }
+    }
+    else
+      line2Buffer[i] = ' ';
+  }
+
+  //EXAMPLE #1
+  if ((displayOption1 & 0x04) == 0x00)  //none scroll display
+    line2Buffer[6] = 'M';
+  else
+  {
+    //example #2
+    if (freqScrollPosition++ > 18)    //none scroll display time
+    {
+      line2Buffer[6] = 'M';
+      if (freqScrollPosition > 25)
+        freqScrollPosition = -1;
+    }
+    else                              //scroll frequency 
+    {
+      line2Buffer[10] = 'H';
+      line2Buffer[11] = 'z';
+  
+      if (freqScrollPosition < 7)   
+      {
+        for (int i = 11; i >= 0; i--)
+          if (i - (7 - freqScrollPosition) >= 0)
+            line2Buffer[i] = line2Buffer[i - (7 - freqScrollPosition)];
+          else
+            line2Buffer[i] = ' ';
+      }
+      else
+      {
+        for (int i = 0; i < 11; i++)
+          if (i + (freqScrollPosition - 7) <= 11)
+            line2Buffer[i] = line2Buffer[i + (freqScrollPosition - 7)];
+          else
+            line2Buffer[i] = ' ';
+      }
+    }
+  } //scroll
+  
+  line2Buffer[7] = ' ';
+  
+  if (isIFShift)
+  {
+//    if (isDirectCall == 1)
+//      for (int i = 0; i < 16; i++)
+//        line2Buffer[i] = ' ';
+      
+      //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
+
+    line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+    line2Buffer[11] = 0;
+    line2Buffer[12] = ' ';
+  
+    //11, 12, 13, 14, 15
+    memset(b, 0, sizeof(b));
+    ltoa(ifShiftValue, b, DEC);
+    strncat(line2Buffer, b, 5);
+    
+    //if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
+    printLine2(line2Buffer);    
+  }       // end of display IF
+  else    // step & Key Type display
+  {
+    //if (isDirectCall != 0)
+    //  return;
+
+    memset(&line2Buffer[8], ' ', 8);
+    //Step
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
+      if (tmpStep > 0) {
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
+          tmpStep /= 10;
+      }
+      else
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[11] = 'H';
+      line2Buffer[12] = 'z';
+    }
+  
+    line2Buffer[13] = ' ';
+    
+    //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+    if (sdrModeOn == 1)
+    {
+      line2Buffer[13] = 'S';
+      line2Buffer[14] = 'D';
+      line2Buffer[15] = 'R';
+    }
+    else if (cwKeyType == 0)
+    {
+      line2Buffer[14] = 'S';
+      line2Buffer[15] = 'T';
+    }
+    else if (cwKeyType == 1)
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'A';
+    }
+    else
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'B';
+    }    
+  }
+}
+
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  if (meterType == 0 || meterType == 1 || meterType == 2)
+  {
+    drawMeter(meterValue);
+    int lineNumber = 0;
+    if ((displayOption1 & 0x01) == 0x01)
+      lineNumber = 1;
+    
+    LCD_SetCursor(drawPosition, lineNumber);
+  
+    //for (int i = 0; i <26; i++) //meter 5 + +db 1 = 6
+    LCD_Write(lcdMeter[0]);
+    LCD_Write(lcdMeter[1]);
+  }
+}
+
+byte testValue = 0;
+char checkCount = 0;
+char checkCountSMeter = 0;
+
+int currentSMeter = 0;
+byte scaledSMeter = 0;
+
+void idle_process()
+{
+  //space for user graphic display
+  if (menuOn == 0)
+  {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
+    //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
+    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
+        printLine2(line2Buffer);
+        line2DisplayStatus = 2;
+        checkCount = 0;
+      }
+    }
+
+      //EX for Meters
+      /*
+      DisplayMeter(0, testValue++, 7);
+      if (testValue > 30)
+        testValue = 0;
+      */
+
+    //S-Meter Display
+    if (((displayOption1 & 0x08) == 0x08 && (sdrModeOn == 0)) && (++checkCountSMeter > SMeterLatency))
+    {
+      int newSMeter;
+
+      //VK2ETA S-Meter from MAX9814 TC pin / divide 4 by KD8CEC for reduce EEPromSize
+      newSMeter = analogRead(ANALOG_SMETER);
+  
+      //Faster attack, Slower release
+      currentSMeter = (newSMeter > currentSMeter ? ((currentSMeter * 3 + newSMeter * 7) + 5) / 10 : ((currentSMeter * 7 + newSMeter * 3) + 5) / 10) / 4;
+  
+      scaledSMeter = 0;
+      for (byte s = 8; s >= 1; s--) {
+        if (currentSMeter > sMeterLevels[s]) {
+          scaledSMeter = s;
+          break;
+        }
+      }
+  
+      DisplayMeter(0, scaledSMeter, 14);
+      checkCountSMeter = 0; //Reset Latency time
+    }   //end of S-Meter
+    
+  }
+}
+
+//AutoKey LCD Display Routine
+void Display_AutoKeyTextIndex(byte textIndex)
+{
+  byte diplayAutoCWLine = 0;
+  
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayAutoCWLine = 1;
+  LCD_SetCursor(0, diplayAutoCWLine);
+  LCD_Write(byteToChar(textIndex));
+  LCD_Write(':');
+}
+
+void DisplayCallsign(byte callSignLength)
+{
+  printLineFromEEPRom(0, 0, 0, userCallsignLength -1, 0); //eeprom to lcd use offset (USER_CALLSIGN_DAT)
+  //delay(500);
+}
+
+void DisplayVersionInfo(const __FlashStringHelper * fwVersionInfo)
+{
+  printLineF(1, fwVersionInfo);
+}
+
+#endif

ubitx_20/ubitx_lcd_1602Dual.ino

@@ -0,0 +1,771 @@
+/*************************************************************************
+  KD8CEC's uBITX Display Routine for LCD1602 Dual LCD by KD8CEC
+  1.This is the display code for the default LCD mounted in uBITX.
+  2.Display related functions of uBITX.  Some functions moved from uBITX_Ui.
+  3.uBITX Idle time Processing
+    Functions that run at times that do not affect TX, CW, and CAT
+    It is called in 1/10 time unit.
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+**************************************************************************/
+#include "ubitx.h"
+
+//Common Defines *********************************************************
+#define LCD_CLEARDISPLAY 0x01
+#define LCD_RETURNHOME 0x02
+#define LCD_ENTRYMODESET 0x04
+#define LCD_DISPLAYCONTROL 0x08
+#define LCD_CURSORSHIFT 0x10
+#define LCD_FUNCTIONSET 0x20
+#define LCD_SETCGRAMADDR 0x40
+#define LCD_SETDDRAMADDR 0x80
+
+// flags for display entry mode
+#define LCD_ENTRYRIGHT 0x00
+#define LCD_ENTRYLEFT 0x02
+#define LCD_ENTRYSHIFTINCREMENT 0x01
+#define LCD_ENTRYSHIFTDECREMENT 0x00
+
+// flags for display on/off control
+#define LCD_DISPLAYON 0x04
+#define LCD_DISPLAYOFF 0x00
+#define LCD_CURSORON 0x02
+#define LCD_CURSOROFF 0x00
+#define LCD_BLINKON 0x01
+#define LCD_BLINKOFF 0x00
+
+// flags for display/cursor shift
+#define LCD_DISPLAYMOVE 0x08
+#define LCD_CURSORMOVE 0x00
+#define LCD_MOVERIGHT 0x04
+#define LCD_MOVELEFT 0x00
+
+// flags for function set
+#define LCD_8BITMODE 0x10
+#define LCD_4BITMODE 0x00
+#define LCD_2LINE 0x08
+#define LCD_1LINE 0x00
+#define LCD_5x10DOTS 0x04
+#define LCD_5x8DOTS 0x00
+
+// flags for backlight control
+#define LCD_BACKLIGHT 0x08
+#define LCD_NOBACKLIGHT 0x00
+
+//========================================================================
+//Begin of I2CTinyLCD Library for Dual LCD by KD8CEC
+//========================================================================
+#ifdef UBITX_DISPLAY_LCD1602I_DUAL
+
+#include <Wire.h>
+/*************************************************************************
+  I2C Tiny LCD Library
+  Referecnce Source : LiquidCrystal_I2C.cpp // Based on the work by DFRobot
+  KD8CEC
+
+  This source code is modified version for small program memory 
+  from Arduino LiquidCrystal_I2C Library
+
+  I wrote this code myself, so there is no license restriction. 
+  So this code allows anyone to write with confidence.
+  But keep it as long as the original author of the code.
+  Ian KD8CEC
+**************************************************************************/
+#define UBITX_DISPLAY_LCD1602_BASE
+
+#define En B00000100  // Enable bit
+#define Rw B00000010  // Read/Write bit
+#define Rs B00000001  // Register select bit
+
+#define LCD_Command(x)  (LCD_Send(x, 0))
+#define LCD_Write(x)    (LCD_Send(x, Rs))
+
+uint8_t _Addr;
+uint8_t _displayfunction;
+uint8_t _displaycontrol;
+uint8_t _displaymode;
+uint8_t _numlines;
+uint8_t _cols;
+uint8_t _rows;
+uint8_t _backlightval;
+
+#define printIIC(args)  Wire.write(args)
+
+void expanderWrite(uint8_t _data)
+{
+  Wire.beginTransmission(_Addr);
+  printIIC((int)(_data) | _backlightval);
+  Wire.endTransmission();   
+}
+
+void pulseEnable(uint8_t _data){
+  expanderWrite(_data | En);  // En high
+  delayMicroseconds(1);       // enable pulse must be >450ns
+  
+  expanderWrite(_data & ~En); // En low
+  delayMicroseconds(50);      // commands need > 37us to settle
+}
+
+void write4bits(uint8_t value) 
+{
+  expanderWrite(value);
+  pulseEnable(value);
+}
+
+void LCD_Send(uint8_t value, uint8_t mode)
+{
+  uint8_t highnib=value&0xf0;
+  uint8_t lownib=(value<<4)&0xf0;
+       write4bits((highnib)|mode);
+  write4bits((lownib)|mode); 
+}
+
+
+// Turn the (optional) backlight off/on
+void noBacklight(void) {
+  _backlightval=LCD_NOBACKLIGHT;
+  expanderWrite(0);
+}
+
+void backlight(void) {
+  _backlightval=LCD_BACKLIGHT;
+  expanderWrite(0);
+}
+
+void LCD1602_Dual_Init()
+{
+  //I2C Init
+  _cols = 16;
+  _rows = 2;
+  _backlightval = LCD_NOBACKLIGHT;
+  Wire.begin();
+
+  delay(50);
+  
+  // Now we pull both RS and R/W low to begin commands
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+  expanderWrite(_backlightval); // reset expanderand turn backlight off (Bit 8 =1)
+  _Addr = I2C_LCD_SECOND_ADDRESS;
+  expanderWrite(_backlightval); // reset expanderand turn backlight off (Bit 8 =1)
+  delay(1000);
+      //put the LCD into 4 bit mode
+  // this is according to the hitachi HD44780 datasheet
+  // figure 24, pg 46
+  
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+    // we start in 8bit mode, try to set 4 bit mode
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // second try
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // third go!
+   write4bits(0x03 << 4); 
+   delayMicroseconds(150);
+   
+   // finally, set to 4-bit interface
+   write4bits(0x02 << 4); 
+
+  // finally, set # lines, font size, etc.
+  LCD_Command(LCD_FUNCTIONSET | LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS | LCD_2LINE);  
+
+  // turn the display on with no cursor or blinking default
+  LCD_Command(LCD_DISPLAYCONTROL | LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF);
+
+  // clear it off
+  LCD_Command(LCD_CLEARDISPLAY);  // clear display, set cursor position to zero
+  //delayMicroseconds(2000);  // this command takes a long time!
+  delayMicroseconds(1000);  // this command takes a long time!
+
+  LCD_Command(LCD_ENTRYMODESET | LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT);
+
+  backlight();
+
+
+  _Addr = I2C_LCD_SECOND_ADDRESS;
+    // we start in 8bit mode, try to set 4 bit mode
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // second try
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // third go!
+   write4bits(0x03 << 4); 
+   delayMicroseconds(150);
+   
+   // finally, set to 4-bit interface
+   write4bits(0x02 << 4); 
+
+  // finally, set # lines, font size, etc.
+  LCD_Command(LCD_FUNCTIONSET | LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS | LCD_2LINE);  
+
+  // turn the display on with no cursor or blinking default
+  LCD_Command(LCD_DISPLAYCONTROL | LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF);
+
+  // clear it off
+  LCD_Command(LCD_CLEARDISPLAY);  // clear display, set cursor position to zero
+  //delayMicroseconds(2000);  // this command takes a long time!
+  delayMicroseconds(1000);  // this command takes a long time!
+
+  LCD_Command(LCD_ENTRYMODESET | LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT);
+
+  backlight();
+
+  //Change to Default LCD (Master)
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+}
+
+
+//========================================================================
+// 16 X 02 LCD Routines
+//Begin of Display Base Routines (Init, printLine..)
+//========================================================================
+
+void LCD_Print(const char *c) 
+{
+  for (uint8_t i = 0; i < strlen(c); i++)
+  {
+    if (*(c + i) == 0x00) return;
+    LCD_Write(*(c + i));
+  }
+}
+
+const int row_offsets[] = { 0x00, 0x40, 0x14, 0x54 };
+void LCD_SetCursor(uint8_t col, uint8_t row)
+{
+  LCD_Command(LCD_SETDDRAMADDR | (col + row_offsets[row]));  //0 : 0x00, 1 : 0x40, only for 20 x 4 lcd
+}
+
+void LCD_CreateChar(uint8_t location, uint8_t charmap[]) 
+{
+  location &= 0x7; // we only have 8 locations 0-7
+  LCD_Command(LCD_SETCGRAMADDR | (location << 3));
+  for (int i=0; i<8; i++)
+    LCD_Write(charmap[i]);
+}
+
+//SWR GRAPH,  DrawMeter and drawingMeter Logic function by VK2ETA 
+//#define OPTION_SKINNYBARS
+
+char c[30], b[30];
+char printBuff[4][20];  //mirrors what is showing on the two lines of the display
+
+void LCD_Init(void)
+{
+  LCD1602_Dual_Init();  
+
+  _Addr = I2C_LCD_SECOND_ADDRESS;
+  initMeter(); //for Meter Display  //when dual LCD, S.Meter on second LCD
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+}
+
+
+// The generic routine to display one line on the LCD 
+void printLine(unsigned char linenmbr, const char *c) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  if (strcmp(c, printBuff[linenmbr])) {     // only refresh the display when there was a change
+    LCD_SetCursor(0, linenmbr);             // place the cursor at the beginning of the selected line
+    LCD_Print(c);
+    strcpy(printBuff[linenmbr], c);
+
+    for (byte i = strlen(c); i < 20; i++) { // add white spaces until the end of the 20 characters line is reached
+      LCD_Write(' ');
+    }
+  }
+}
+
+void printLineF(char linenmbr, const __FlashStringHelper *c)
+{
+  int i;
+  char tmpBuff[21];
+  PGM_P p = reinterpret_cast<PGM_P>(c);  
+
+  for (i = 0; i < 21; i++){
+    unsigned char fChar = pgm_read_byte(p++);
+    tmpBuff[i] = fChar;
+    if (fChar == 0)
+      break;
+  }
+
+  printLine(linenmbr, tmpBuff);
+}
+
+#define LCD_MAX_COLUMN 20
+void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetTtype) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  
+  LCD_SetCursor(lcdColumn, linenmbr);
+
+  for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
+  {
+    if (++lcdColumn <= LCD_MAX_COLUMN)
+      LCD_Write(EEPROM.read((offsetTtype == 0 ? USER_CALLSIGN_DAT : WSPR_MESSAGE1) + i));
+    else
+      break;
+  }
+  
+  for (byte i = lcdColumn; i < 20; i++) //Right Padding by Space
+      LCD_Write(' ');
+}
+
+//  short cut to print to the first line
+void printLine1(const char *c)
+{
+  printLine(1,c);
+}
+//  short cut to print to the first line
+void printLine2(const char *c)
+{
+  printLine(0,c);
+}
+
+void clearLine2()
+{
+  printLine2("");
+  line2DisplayStatus = 0;
+}
+
+//  short cut to print to the first line
+void printLine1Clear(){
+  printLine(1,"");
+}
+//  short cut to print to the first line
+void printLine2Clear(){
+  printLine(0, "");
+}
+
+void printLine2ClearAndUpdate(){
+  printLine(0, "");
+  line2DisplayStatus = 0;  
+  updateDisplay();
+}
+
+//==================================================================================
+//End of Display Base Routines
+//==================================================================================
+
+
+//==================================================================================
+//Begin of User Interface Routines
+//==================================================================================
+
+//Main Display
+// this builds up the top line of the display with frequency and mode
+void updateDisplay() {
+  // tks Jack Purdum W8TEE
+  // replaced fsprint commmands by str commands for code size reduction
+  // replace code for Frequency numbering error (alignment, point...) by KD8CEC
+  // i also Very TNX Purdum for good source code
+  int i;
+  unsigned long tmpFreq = frequency; //
+  
+  memset(c, 0, sizeof(c));
+
+  if (inTx){
+    if (isCWAutoMode == 2) {
+      for (i = 0; i < 4; i++)
+        c[3-i] = (i < autoCWSendReservCount ? byteToChar(autoCWSendReserv[i]) : ' ');
+
+      //display Sending Index
+      c[4] = byteToChar(sendingCWTextIndex);
+      c[5] = '=';
+    }
+    else {
+      if (cwTimeout > 0)
+        strcpy(c, "   CW:");
+      else
+        strcpy(c, "   TX:");
+    }
+  }
+  else {
+    if (ritOn)
+      strcpy(c, "RIT ");
+    else {
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          strcpy(c, "USB ");
+        else
+          strcpy(c, "LSB ");
+      }
+      else if (cwMode == 1)
+      {
+          strcpy(c, "CWL ");
+      }
+      else
+      {
+          strcpy(c, "CWU ");
+      }
+    }
+    
+    if (vfoActive == VFO_A) // VFO A is active
+      strcat(c, "A:");
+    else
+      strcat(c, "B:");
+  }
+
+  //Fixed by Mitani Massaru (JE4SMQ)
+  if (isShiftDisplayCWFreq == 1)
+  {
+    if (cwMode == 1)        //CWL
+        tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+    else if (cwMode == 2)   //CWU
+        tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+  }
+
+  //display frequency
+  for (int i = 15; i >= 6; i--) {
+    if (tmpFreq > 0) {
+      if (i == 12 || i == 8) c[i] = '.';
+      else {
+        c[i] = tmpFreq % 10 + 0x30;
+        tmpFreq /= 10;
+      }
+    }
+    else
+      c[i] = ' ';
+  }
+
+  //remarked by KD8CEC
+  //already RX/TX status display, and over index (16 x 2 LCD)
+  printLine(1, c);
+
+  byte diplayVFOLine = 1;
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayVFOLine = 0;
+
+  if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
+    (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02))) {
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write((uint8_t)0);
+  }
+  else if (isCWAutoMode == 2){
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write(0x7E);
+  }
+  else
+  {
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write(':');
+  }
+}
+
+
+
+char line2Buffer[20];
+//KD8CEC 200Hz ST
+//L14.150 200Hz ST
+//U14.150 +150khz
+int freqScrollPosition = 0;
+
+//Example Line2 Optinal Display
+//immediate execution, not call by scheulder
+//warning : unused parameter 'displayType' <-- ignore, this is reserve
+void updateLine2Buffer(char displayType)
+{
+  unsigned long tmpFreq = 0;
+  if (ritOn)
+  {
+    strcpy(line2Buffer, "RitTX:");
+
+    //display frequency
+    tmpFreq = ritTxFrequency;
+
+    //Fixed by Mitani Massaru (JE4SMQ)
+    if (isShiftDisplayCWFreq == 1)
+    {
+      if (cwMode == 1)        //CWL
+          tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+      else if (cwMode == 2)   //CWU
+          tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+    }
+    
+    for (int i = 15; i >= 6; i--) {
+      if (tmpFreq > 0) {
+        if (i == 12 || i == 8) line2Buffer[i] = '.';
+        else {
+          line2Buffer[i] = tmpFreq % 10 + 0x30;
+          tmpFreq /= 10;
+        }
+      }
+      else
+        line2Buffer[i] = ' ';
+    }
+
+    return;
+  } //end of ritOn display
+
+  //other VFO display
+  if (vfoActive == VFO_B)
+  {
+    tmpFreq = vfoA;
+  }
+  else 
+  {
+    tmpFreq = vfoB;
+  }
+
+  // EXAMPLE 1 & 2
+  //U14.150.100
+  //display frequency
+  for (int i = 9; i >= 0; i--) {
+    if (tmpFreq > 0) {
+      if (i == 2 || i == 6) line2Buffer[i] = '.';
+      else {
+        line2Buffer[i] = tmpFreq % 10 + 0x30;
+        tmpFreq /= 10;
+      }
+    }
+    else
+      line2Buffer[i] = ' ';
+  }
+  
+  memset(&line2Buffer[10], ' ', 10);
+  
+  if (isIFShift)
+  {
+    line2Buffer[6] = 'M';
+    line2Buffer[7] = ' ';
+    //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
+
+    line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+    line2Buffer[11] = 0;
+    line2Buffer[12] = ' ';
+  
+    //11, 12, 13, 14, 15
+    memset(b, 0, sizeof(b));
+    ltoa(ifShiftValue, b, DEC);
+    strncat(line2Buffer, b, 5);
+
+    for (int i = 12; i < 17; i++)
+    {
+      if (line2Buffer[i] == 0)
+        line2Buffer[i] = ' ';
+    }
+  }       // end of display IF
+  else    // step & Key Type display
+  {
+    //Step
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 13; i >= 11 - isStepKhz; i--) {
+      if (tmpStep > 0) {
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
+          tmpStep /= 10;
+      }
+      else
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[14] = 'H';
+      line2Buffer[15] = 'z';
+    }
+  }
+
+  //line2Buffer[17] = ' ';
+  /* ianlee  
+  //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+  if (cwKeyType == 0)
+  {
+    line2Buffer[18] = 'S';
+    line2Buffer[19] = 'T';
+  }
+  else if (cwKeyType == 1)
+  {
+    line2Buffer[18] = 'I';
+    line2Buffer[19] = 'A';
+  }
+  else
+  {
+    line2Buffer[18] = 'I';
+    line2Buffer[19] = 'B';
+  }
+*/
+
+}
+
+
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  if (meterType == 0 || meterType == 1 || meterType == 2)
+  {
+    drawMeter(meterValue);
+
+    LCD_SetCursor(drawPosition, 0);
+    LCD_Write('S');
+      
+    LCD_Write(':');
+    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+      LCD_Write(lcdMeter[i]);
+  }
+}
+
+
+byte testValue = 0;
+char checkCount = 0;
+
+int currentSMeter = 0;
+byte scaledSMeter = 0;
+char checkCountSMeter = 0;
+
+char beforeKeyType = -1;
+char displaySDRON = 0;
+
+//execute interval : 0.25sec
+void idle_process()
+{
+  //space for user graphic display
+  if (menuOn == 0)
+  {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
+    //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
+    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
+        printLine2(line2Buffer);
+        line2DisplayStatus = 2;
+        checkCount = 0;
+
+        //check change CW Key Type
+        if (beforeKeyType != cwKeyType)
+        {
+          _Addr = I2C_LCD_SECOND_ADDRESS;
+          LCD_SetCursor(10, 0);
+          LCD_Write('K');
+          LCD_Write('E');
+          LCD_Write('Y');
+          LCD_Write(':');
+          
+          //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+          if (cwKeyType == 0)
+          {
+            LCD_Write('S');
+            LCD_Write('T');
+          }
+          else if (cwKeyType == 1)
+          {
+            LCD_Write('I');
+            LCD_Write('A');
+          }
+          else
+          {
+            LCD_Write('I');
+            LCD_Write('B');
+          }
+
+          beforeKeyType = cwKeyType;
+          _Addr = I2C_LCD_MASTER_ADDRESS;
+        } //Display Second Screen
+        
+      }
+    }
+
+    //EX for Meters
+    
+    //S-Meter Display
+    _Addr = I2C_LCD_SECOND_ADDRESS;
+    if (sdrModeOn == 1)
+    {
+      if (displaySDRON == 0)  //once display
+      {
+        displaySDRON = 1;       
+        LCD_SetCursor(0, 0);
+        LCD_Write('S');
+        LCD_Write('D');
+        LCD_Write('R');
+        LCD_Write(' ');
+        LCD_Write('M');
+        LCD_Write('O');
+        LCD_Write('D');
+        LCD_Write('E');
+      }
+    }
+    else if (((displayOption1 & 0x08) == 0x08) && (++checkCountSMeter > 3))
+    {
+      int newSMeter;
+      displaySDRON = 0;
+  
+      //VK2ETA S-Meter from MAX9814 TC pin
+      newSMeter = analogRead(ANALOG_SMETER);
+  
+      //Faster attack, Slower release
+      //currentSMeter = (newSMeter > currentSMeter ? ((currentSMeter * 3 + newSMeter * 7) + 5) / 10 : ((currentSMeter * 7 + newSMeter * 3) + 5) / 10);
+      currentSMeter = (currentSMeter * 3 + newSMeter * 7) / 10; //remarked becaused of have already Latency time
+  
+      scaledSMeter = 0;
+      for (byte s = 8; s >= 1; s--) {
+        if (currentSMeter > sMeterLevels[s]) {
+          scaledSMeter = s;
+          break;
+        }
+      }
+  
+      DisplayMeter(0, scaledSMeter, 0);
+      
+      checkCountSMeter = 0;
+    } //end of S-Meter
+    _Addr = I2C_LCD_MASTER_ADDRESS;
+
+   
+  }
+}
+
+//AutoKey LCD Display Routine
+void Display_AutoKeyTextIndex(byte textIndex)
+{
+  byte diplayAutoCWLine = 0;
+  
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayAutoCWLine = 1;
+  LCD_SetCursor(0, diplayAutoCWLine);
+  LCD_Write(byteToChar(textIndex));
+  LCD_Write(':');
+}
+
+void DisplayCallsign(byte callSignLength)
+{
+  _Addr = I2C_LCD_SECOND_ADDRESS;
+  printLineFromEEPRom(1, 16 - userCallsignLength, 0, userCallsignLength -1, 0); //eeprom to lcd use offset (USER_CALLSIGN_DAT)
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+}
+
+void DisplayVersionInfo(const __FlashStringHelper * fwVersionInfo)
+{
+  _Addr = I2C_LCD_SECOND_ADDRESS;
+  printLineF(1, fwVersionInfo);
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+}
+
+#endif

ubitx_20/ubitx_lcd_2004.ino

@@ -0,0 +1,855 @@
+/*************************************************************************
+  KD8CEC's uBITX Display Routine for LCD2004 Parrel
+  1.This is the display code for the default LCD mounted in uBITX.
+  2.Display related functions of uBITX.  Some functions moved from uBITX_Ui.
+  3.uBITX Idle time Processing
+    Functions that run at times that do not affect TX, CW, and CAT
+    It is called in 1/10 time unit.
+-----------------------------------------------------------------------------
+   This program is free software: you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+**************************************************************************/
+#include "ubitx.h"
+
+//Common Defines *********************************************************
+#define LCD_CLEARDISPLAY 0x01
+#define LCD_RETURNHOME 0x02
+#define LCD_ENTRYMODESET 0x04
+#define LCD_DISPLAYCONTROL 0x08
+#define LCD_CURSORSHIFT 0x10
+#define LCD_FUNCTIONSET 0x20
+#define LCD_SETCGRAMADDR 0x40
+#define LCD_SETDDRAMADDR 0x80
+
+// flags for display entry mode
+#define LCD_ENTRYRIGHT 0x00
+#define LCD_ENTRYLEFT 0x02
+#define LCD_ENTRYSHIFTINCREMENT 0x01
+#define LCD_ENTRYSHIFTDECREMENT 0x00
+
+// flags for display on/off control
+#define LCD_DISPLAYON 0x04
+#define LCD_DISPLAYOFF 0x00
+#define LCD_CURSORON 0x02
+#define LCD_CURSOROFF 0x00
+#define LCD_BLINKON 0x01
+#define LCD_BLINKOFF 0x00
+
+// flags for display/cursor shift
+#define LCD_DISPLAYMOVE 0x08
+#define LCD_CURSORMOVE 0x00
+#define LCD_MOVERIGHT 0x04
+#define LCD_MOVELEFT 0x00
+
+// flags for function set
+#define LCD_8BITMODE 0x10
+#define LCD_4BITMODE 0x00
+#define LCD_2LINE 0x08
+#define LCD_1LINE 0x00
+#define LCD_5x10DOTS 0x04
+#define LCD_5x8DOTS 0x00
+
+// flags for backlight control
+#define LCD_BACKLIGHT 0x08
+#define LCD_NOBACKLIGHT 0x00
+
+//========================================================================
+//Begin of TinyLCD Library by KD8CEC
+//========================================================================
+
+#ifdef UBITX_DISPLAY_LCD2004P
+/*************************************************************************
+  LCD2004TINY Library for 20 x 4 LCD
+  Referecnce Source : LiquidCrystal.cpp 
+  KD8CEC
+
+  This source code is modified version for small program memory 
+  from Arduino LiquidCrystal Library
+
+  I wrote this code myself, so there is no license restriction. 
+  So this code allows anyone to write with confidence.
+  But keep it as long as the original author of the code.
+  DE Ian KD8CEC
+**************************************************************************/
+#define LCD_Command(x)  (LCD_Send(x, LOW))
+#define LCD_Write(x)    (LCD_Send(x, HIGH))
+
+#define UBITX_DISPLAY_LCD2004_BASE
+
+//Define  connected PIN
+#define LCD_PIN_RS 8
+#define LCD_PIN_EN 9
+uint8_t LCD_PIN_DAT[4] = {10, 11, 12, 13};
+
+void write4bits(uint8_t value) 
+{
+  for (int i = 0; i < 4; i++) 
+    digitalWrite(LCD_PIN_DAT[i], (value >> i) & 0x01);
+
+  digitalWrite(LCD_PIN_EN, LOW);
+  delayMicroseconds(1);    
+  digitalWrite(LCD_PIN_EN, HIGH);
+  delayMicroseconds(1);    // enable pulse must be >450ns
+  digitalWrite(LCD_PIN_EN, LOW);
+  delayMicroseconds(100);   // commands need > 37us to settle
+}
+
+void LCD_Send(uint8_t value, uint8_t mode)
+{
+    digitalWrite(LCD_PIN_RS, mode);
+    write4bits(value>>4);
+    write4bits(value);
+}
+
+void LCD2004_Init()
+{
+  pinMode(LCD_PIN_RS, OUTPUT);
+  pinMode(LCD_PIN_EN, OUTPUT);
+  for (int i = 0; i < 4; i++)
+    pinMode(LCD_PIN_DAT[i], OUTPUT);
+
+  delayMicroseconds(50); 
+ 
+  // Now we pull both RS and R/W low to begin commands
+  digitalWrite(LCD_PIN_RS, LOW);
+  digitalWrite(LCD_PIN_EN, LOW);
+
+  // we start in 8bit mode, try to set 4 bit mode
+  write4bits(0x03);
+  delayMicroseconds(4500); // wait min 4.1ms
+  
+  // second try
+  write4bits(0x03);
+  delayMicroseconds(4500); // wait min 4.1ms
+  
+  // third go!
+  write4bits(0x03); 
+  delayMicroseconds(150);
+  
+  // finally, set to 4-bit interface
+  write4bits(0x02);
+
+  // finally, set # lines, font size, etc.
+  LCD_Command(LCD_FUNCTIONSET | LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS | LCD_2LINE);  
+
+  // turn the display on with no cursor or blinking default
+  LCD_Command(LCD_DISPLAYCONTROL | LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF);
+
+  // clear it off
+  LCD_Command(LCD_CLEARDISPLAY);  // clear display, set cursor position to zero
+  delayMicroseconds(2000);  // this command takes a long time!
+
+  LCD_Command(LCD_ENTRYMODESET | LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT);
+}
+#endif
+//========================================================================
+//End of TinyLCD Library by KD8CEC
+//========================================================================
+
+
+
+//========================================================================
+//Begin of I2CTinyLCD Library by KD8CEC
+//========================================================================
+#ifdef UBITX_DISPLAY_LCD2004I
+
+#include <Wire.h>
+/*************************************************************************
+  I2C Tiny LCD Library
+  Referecnce Source : LiquidCrystal_I2C.cpp // Based on the work by DFRobot
+  KD8CEC
+
+  This source code is modified version for small program memory 
+  from Arduino LiquidCrystal_I2C Library
+
+  I wrote this code myself, so there is no license restriction. 
+  So this code allows anyone to write with confidence.
+  But keep it as long as the original author of the code.
+  Ian KD8CEC
+**************************************************************************/
+#define UBITX_DISPLAY_LCD2004_BASE
+
+#define En B00000100  // Enable bit
+#define Rw B00000010  // Read/Write bit
+#define Rs B00000001  // Register select bit
+
+#define LCD_Command(x)  (LCD_Send(x, 0))
+#define LCD_Write(x)    (LCD_Send(x, Rs))
+
+uint8_t _Addr;
+uint8_t _displayfunction;
+uint8_t _displaycontrol;
+uint8_t _displaymode;
+uint8_t _numlines;
+uint8_t _cols;
+uint8_t _rows;
+uint8_t _backlightval;
+
+#define printIIC(args)  Wire.write(args)
+
+void expanderWrite(uint8_t _data)
+{
+  Wire.beginTransmission(_Addr);
+  printIIC((int)(_data) | _backlightval);
+  Wire.endTransmission();   
+}
+
+void pulseEnable(uint8_t _data){
+  expanderWrite(_data | En);  // En high
+  delayMicroseconds(1);       // enable pulse must be >450ns
+  
+  expanderWrite(_data & ~En); // En low
+  delayMicroseconds(50);      // commands need > 37us to settle
+}
+
+void write4bits(uint8_t value) 
+{
+  expanderWrite(value);
+  pulseEnable(value);
+}
+
+void LCD_Send(uint8_t value, uint8_t mode)
+{
+  uint8_t highnib=value&0xf0;
+  uint8_t lownib=(value<<4)&0xf0;
+       write4bits((highnib)|mode);
+  write4bits((lownib)|mode); 
+}
+
+
+// Turn the (optional) backlight off/on
+void noBacklight(void) {
+  _backlightval=LCD_NOBACKLIGHT;
+  expanderWrite(0);
+}
+
+void backlight(void) {
+  _backlightval=LCD_BACKLIGHT;
+  expanderWrite(0);
+}
+
+void LCD2004_Init()
+{
+  //I2C Init
+  _Addr = I2C_LCD_MASTER_ADDRESS;
+  _cols = 20;
+  _rows = 4;
+  _backlightval = LCD_NOBACKLIGHT;
+  Wire.begin();
+
+  delay(50);
+  
+  // Now we pull both RS and R/W low to begin commands
+  expanderWrite(_backlightval); // reset expanderand turn backlight off (Bit 8 =1)
+  delay(1000);
+      //put the LCD into 4 bit mode
+  // this is according to the hitachi HD44780 datasheet
+  // figure 24, pg 46
+  
+    // we start in 8bit mode, try to set 4 bit mode
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // second try
+   write4bits(0x03 << 4);
+   delayMicroseconds(4500); // wait min 4.1ms
+   
+   // third go!
+   write4bits(0x03 << 4); 
+   delayMicroseconds(150);
+   
+   // finally, set to 4-bit interface
+   write4bits(0x02 << 4); 
+
+  // finally, set # lines, font size, etc.
+  LCD_Command(LCD_FUNCTIONSET | LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS | LCD_2LINE);  
+
+  // turn the display on with no cursor or blinking default
+  LCD_Command(LCD_DISPLAYCONTROL | LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF);
+
+  // clear it off
+  LCD_Command(LCD_CLEARDISPLAY);  // clear display, set cursor position to zero
+  //delayMicroseconds(2000);  // this command takes a long time!
+  delayMicroseconds(1000);  // this command takes a long time!
+
+  LCD_Command(LCD_ENTRYMODESET | LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT);
+
+  backlight();
+}
+#endif
+//========================================================================
+//End of I2CTinyLCD Library by KD8CEC
+//========================================================================
+
+
+//========================================================================
+// 20 X 04 LCD Routines
+//Begin of Display Base Routines (Init, printLine..)
+//========================================================================
+#ifdef UBITX_DISPLAY_LCD2004_BASE
+
+void LCD_Print(const char *c) 
+{
+  for (uint8_t i = 0; i < strlen(c); i++)
+  {
+    if (*(c + i) == 0x00) return;
+    LCD_Write(*(c + i));
+  }
+}
+
+const int row_offsets[] = { 0x00, 0x40, 0x14, 0x54 };
+void LCD_SetCursor(uint8_t col, uint8_t row)
+{
+  LCD_Command(LCD_SETDDRAMADDR | (col + row_offsets[row]));  //0 : 0x00, 1 : 0x40, only for 20 x 4 lcd
+}
+
+void LCD_CreateChar(uint8_t location, uint8_t charmap[]) 
+{
+  location &= 0x7; // we only have 8 locations 0-7
+  LCD_Command(LCD_SETCGRAMADDR | (location << 3));
+  for (int i=0; i<8; i++)
+    LCD_Write(charmap[i]);
+}
+
+//SWR GRAPH,  DrawMeter and drawingMeter Logic function by VK2ETA 
+//#define OPTION_SKINNYBARS
+
+char c[30], b[30];
+char printBuff[4][21];  //mirrors what is showing on the two lines of the display
+
+void LCD_Init(void)
+{
+  LCD2004_Init();  
+  initMeter(); //for Meter Display
+}
+
+
+// The generic routine to display one line on the LCD 
+void printLine(unsigned char linenmbr, const char *c) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  if (strcmp(c, printBuff[linenmbr])) {     // only refresh the display when there was a change
+    LCD_SetCursor(0, linenmbr);             // place the cursor at the beginning of the selected line
+    LCD_Print(c);
+    strcpy(printBuff[linenmbr], c);
+
+    for (byte i = strlen(c); i < 20; i++) { // add white spaces until the end of the 20 characters line is reached
+      LCD_Write(' ');
+    }
+  }
+}
+
+void printLineF(char linenmbr, const __FlashStringHelper *c)
+{
+  int i;
+  char tmpBuff[21];
+  PGM_P p = reinterpret_cast<PGM_P>(c);  
+
+  for (i = 0; i < 21; i++){
+    unsigned char fChar = pgm_read_byte(p++);
+    tmpBuff[i] = fChar;
+    if (fChar == 0)
+      break;
+  }
+
+  printLine(linenmbr, tmpBuff);
+}
+
+#define LCD_MAX_COLUMN 20
+void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetTtype) {
+  if ((displayOption1 & 0x01) == 0x01)
+    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
+  
+  LCD_SetCursor(lcdColumn, linenmbr);
+
+  for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
+  {
+    if (++lcdColumn <= LCD_MAX_COLUMN)
+      LCD_Write(EEPROM.read((offsetTtype == 0 ? USER_CALLSIGN_DAT : WSPR_MESSAGE1) + i));
+    else
+      break;
+  }
+  
+  for (byte i = lcdColumn; i < 20; i++) //Right Padding by Space
+      LCD_Write(' ');
+}
+
+//  short cut to print to the first line
+void printLine1(const char *c)
+{
+  printLine(1,c);
+}
+//  short cut to print to the first line
+void printLine2(const char *c)
+{
+  printLine(0,c);
+}
+
+void clearLine2()
+{
+  printLine2("");
+  line2DisplayStatus = 0;
+}
+
+//  short cut to print to the first line
+void printLine1Clear(){
+  printLine(1,"");
+}
+//  short cut to print to the first line
+void printLine2Clear(){
+  printLine(0, "");
+}
+
+void printLine2ClearAndUpdate(){
+  printLine(0, "");
+  line2DisplayStatus = 0;  
+  updateDisplay();
+}
+
+//==================================================================================
+//End of Display Base Routines
+//==================================================================================
+
+
+//==================================================================================
+//Begin of User Interface Routines
+//==================================================================================
+
+//Main Display
+// this builds up the top line of the display with frequency and mode
+void updateDisplay() {
+  // tks Jack Purdum W8TEE
+  // replaced fsprint commmands by str commands for code size reduction
+  // replace code for Frequency numbering error (alignment, point...) by KD8CEC
+  // i also Very TNX Purdum for good source code
+  int i;
+  unsigned long tmpFreq = frequency; //
+  
+  memset(c, 0, sizeof(c));
+
+  if (inTx){
+    if (isCWAutoMode == 2) {
+      for (i = 0; i < 4; i++)
+        c[3-i] = (i < autoCWSendReservCount ? byteToChar(autoCWSendReserv[i]) : ' ');
+
+      //display Sending Index
+      c[4] = byteToChar(sendingCWTextIndex);
+      c[5] = '=';
+    }
+    else {
+      if (cwTimeout > 0)
+        strcpy(c, "   CW:");
+      else
+        strcpy(c, "   TX:");
+    }
+  }
+  else {
+    if (ritOn)
+      strcpy(c, "RIT ");
+    else {
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          strcpy(c, "USB ");
+        else
+          strcpy(c, "LSB ");
+      }
+      else if (cwMode == 1)
+      {
+          strcpy(c, "CWL ");
+      }
+      else
+      {
+          strcpy(c, "CWU ");
+      }
+    }
+    
+    if (vfoActive == VFO_A) // VFO A is active
+      strcat(c, "A:");
+    else
+      strcat(c, "B:");
+  }
+
+  //Fixed by Mitani Massaru (JE4SMQ)
+  if (isShiftDisplayCWFreq == 1)
+  {
+    if (cwMode == 1)        //CWL
+        tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+    else if (cwMode == 2)   //CWU
+        tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+  }
+
+  //display frequency
+  for (int i = 15; i >= 6; i--) {
+    if (tmpFreq > 0) {
+      if (i == 12 || i == 8) c[i] = '.';
+      else {
+        c[i] = tmpFreq % 10 + 0x30;
+        tmpFreq /= 10;
+      }
+    }
+    else
+      c[i] = ' ';
+  }
+
+  if (sdrModeOn)
+    strcat(c, " SDR");
+  else
+    strcat(c, " SPK");
+
+  //remarked by KD8CEC
+  //already RX/TX status display, and over index (20 x 4 LCD)
+  //if (inTx)
+  //  strcat(c, " TX");
+  printLine(1, c);
+
+  byte diplayVFOLine = 1;
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayVFOLine = 0;
+
+  if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
+    (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02))) {
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write((uint8_t)0);
+  }
+  else if (isCWAutoMode == 2){
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write(0x7E);
+  }
+  else
+  {
+    LCD_SetCursor(5,diplayVFOLine);
+    LCD_Write(':');
+  }
+}
+
+
+
+char line2Buffer[20];
+//KD8CEC 200Hz ST
+//L14.150 200Hz ST
+//U14.150 +150khz
+int freqScrollPosition = 0;
+
+//Example Line2 Optinal Display
+//immediate execution, not call by scheulder
+//warning : unused parameter 'displayType' <-- ignore, this is reserve
+void updateLine2Buffer(char displayType)
+{
+  unsigned long tmpFreq = 0;
+  if (ritOn)
+  {
+    strcpy(line2Buffer, "RitTX:");
+
+    //display frequency
+    tmpFreq = ritTxFrequency;
+
+    //Fixed by Mitani Massaru (JE4SMQ)
+    if (isShiftDisplayCWFreq == 1)
+    {
+      if (cwMode == 1)        //CWL
+          tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
+      else if (cwMode == 2)   //CWU
+          tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
+    }
+    
+    for (int i = 15; i >= 6; i--) {
+      if (tmpFreq > 0) {
+        if (i == 12 || i == 8) line2Buffer[i] = '.';
+        else {
+          line2Buffer[i] = tmpFreq % 10 + 0x30;
+          tmpFreq /= 10;
+        }
+      }
+      else
+        line2Buffer[i] = ' ';
+    }
+
+    return;
+  } //end of ritOn display
+
+  //other VFO display
+  if (vfoActive == VFO_B)
+  {
+    tmpFreq = vfoA;
+  }
+  else 
+  {
+    tmpFreq = vfoB;
+  }
+
+  // EXAMPLE 1 & 2
+  //U14.150.100
+  //display frequency
+  for (int i = 9; i >= 0; i--) {
+    if (tmpFreq > 0) {
+      if (i == 2 || i == 6) line2Buffer[i] = '.';
+      else {
+        line2Buffer[i] = tmpFreq % 10 + 0x30;
+        tmpFreq /= 10;
+      }
+    }
+    else
+      line2Buffer[i] = ' ';
+  }
+  
+  memset(&line2Buffer[10], ' ', 10);
+  
+  if (isIFShift)
+  {
+    line2Buffer[6] = 'M';
+    line2Buffer[7] = ' ';
+    //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
+
+    line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+    line2Buffer[11] = 0;
+    line2Buffer[12] = ' ';
+  
+    //11, 12, 13, 14, 15
+    memset(b, 0, sizeof(b));
+    ltoa(ifShiftValue, b, DEC);
+    strncat(line2Buffer, b, 5);
+
+    for (int i = 12; i < 17; i++)
+    {
+      if (line2Buffer[i] == 0)
+        line2Buffer[i] = ' ';
+    }
+  }       // end of display IF
+  else    // step & Key Type display
+  {
+    //Step
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 14; i >= 12 - isStepKhz; i--) {
+      if (tmpStep > 0) {
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
+          tmpStep /= 10;
+      }
+      else
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[15] = 'H';
+      line2Buffer[16] = 'z';
+    }
+  }
+
+  line2Buffer[17] = ' ';
+  
+  //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+  if (cwKeyType == 0)
+  {
+    line2Buffer[18] = 'S';
+    line2Buffer[19] = 'T';
+  }
+  else if (cwKeyType == 1)
+  {
+    line2Buffer[18] = 'I';
+    line2Buffer[19] = 'A';
+  }
+  else
+  {
+    line2Buffer[18] = 'I';
+    line2Buffer[19] = 'B';
+  }
+
+}
+
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  if (meterType == 0 || meterType == 1 || meterType == 2)
+  {
+    drawMeter(meterValue);
+    //int lineNumber = 0;
+    //if ((displayOption1 & 0x01) == 0x01)
+    //lineNumber = 1;
+    
+    LCD_SetCursor(drawPosition, 2);
+    LCD_Write('S');
+    LCD_Write(':');
+    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+      LCD_Write(lcdMeter[i]);
+  }
+}
+
+
+//meterType : 0 = S.Meter, 1 = Forward Power Meter, 2 = SWR Meter
+void DisplayMeter(byte meterType, int meterValue, char drawPosition)
+{
+
+#ifdef OPTION_SKINNYBARS //We want skinny meter bars with more text/numbers
+  memcpy(&(line2Buffer[drawPosition]), "        ", 8); //Blank that section of 8 characters first
+  if (meterType == 0) { //SWR meter
+    drawMeter(meterValue); //Only 2 characters
+    line2Buffer[drawPosition] = 'S';
+    byte sValue = round((float)meterValue * 1.5); //6 bars available only to show 9 S values
+    sValue = sValue > 9 ? 9 : sValue; //Max S9
+    line2Buffer[drawPosition + 1] = '0' +  sValue; //0 to 9
+    memcpy(&(line2Buffer[drawPosition + 2]), lcdMeter, 2); //Copy the S-Meter bars
+    //Add the +10, +20, etc...
+    if (meterValue > 6) {
+      //We are over S9
+      line2Buffer[drawPosition + 4] = '+';
+      line2Buffer[drawPosition + 5] = '0' +  meterValue - 6; //1,2,3 etc...
+      line2Buffer[drawPosition + 6] = '0';
+    }
+  } else if (meterType == 1) { //Forward Power
+    drawMeter(round((float)meterValue / 40)); //4 watts per bar
+    //meterValue contains power value x 10 (one decimal point)
+    line2Buffer[drawPosition] = 'P';
+    meterValue = meterValue > 999 ? 999 : meterValue; //Limit to 99.9 watts!!!!
+    //Remove decimal value and divide by 10
+    meterValue = round((float)meterValue / 10);
+    if (meterValue < 10) {
+      line2Buffer[drawPosition + 1] = ' ';
+      line2Buffer[drawPosition + 2] = '0' +  meterValue; //0 to 9
+    } else {
+      line2Buffer[drawPosition + 1] = '0' +  meterValue /  10;
+      line2Buffer[drawPosition + 2] = '0' +  (meterValue - ((meterValue / 10) * 10));
+    }
+    line2Buffer[drawPosition + 3] = 'W';
+    memcpy(&(line2Buffer[drawPosition + 4]), lcdMeter, 2); //Copy the S-Meter bars
+  } else { //SWR
+    drawMeter((int)(((float)meterValue - 21) / 100)); //no bar = < 1.2, then 1 bar = 1.2 to 2.2, 2 bars = 2.2 to 3.2, etc...
+    //meterValue contains SWR x 100 (two decimal point)
+    memcpy(&(line2Buffer[drawPosition]), "SWR", 3);
+    meterValue = round((float)meterValue / 10); //We now have swr x 10 (1 decimal point)
+    if (meterValue < 100) { //10 to 99, no decimal point
+      //Draw the decimal value
+      line2Buffer[drawPosition + 3] = '0' +  meterValue /  10;
+      line2Buffer[drawPosition + 4] = '.';
+      line2Buffer[drawPosition + 5] = '0' +  (meterValue - ((meterValue / 10) * 10));
+    } else {
+      memcpy(&(line2Buffer[drawPosition + 3]), "10+", 3); //over 10
+    }
+    memcpy(&(line2Buffer[drawPosition + 6]), lcdMeter, 2); //Copy the S-Meter bars
+  }
+#else //We want fat bars, easy to read, with less text/numbers
+  //Serial.print("In displaymeter, meterValue: "); Serial.println(meterValue);
+  drawMeter(meterValue);
+  //Always line 2
+  char sym = 'S';
+  if (meterType == 1) sym = 'P';
+  else if (meterType == 2) sym = 'R'; //For SWR
+  line2Buffer[drawPosition] = sym;
+  memcpy(&(line2Buffer[drawPosition + 1]), lcdMeter, 7);
+#endif //OPTION_SKINNYBARS
+
+}
+
+
+byte testValue = 0;
+char checkCount = 0;
+
+int currentSMeter = 0;
+//int sMeterLevels[] = {0, 5, 17, 41, 74, 140, 255, 365, 470};
+byte scaledSMeter = 0;
+char checkCountSMeter = 0;
+
+//execute interval : 0.25sec
+void idle_process()
+{
+  //space for user graphic display
+  if (menuOn == 0)
+  {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
+    //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
+    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
+        printLine2(line2Buffer);
+        line2DisplayStatus = 2;
+        checkCount = 0;
+      }
+    }
+
+    //EX for Meters
+    /*
+    DisplayMeter(0, testValue++, 0);
+    if (testValue > 30)
+      testValue = 0;
+    */
+
+    //Sample
+    //DisplayMeter(0, analogRead(ANALOG_SMETER) / 30, 0);
+    //DisplayMeter(0, analogRead(ANALOG_SMETER) / 10, 0);
+    //delay_background(10, 0);
+    //DisplayMeter(0, analogRead(ANALOG_SMETER), 0);
+    //if (testValue > 30)
+    //  testValue = 0;
+
+    //S-Meter Display
+    if (((displayOption1 & 0x08) == 0x08 && (sdrModeOn == 0)) && (++checkCountSMeter > SMeterLatency))
+    {
+      int newSMeter;
+      
+      //VK2ETA S-Meter from MAX9814 TC pin
+      newSMeter = analogRead(ANALOG_SMETER);
+  
+      //Faster attack, Slower release
+      currentSMeter = (newSMeter > currentSMeter ? ((currentSMeter * 3 + newSMeter * 7) + 5) / 10 : ((currentSMeter * 7 + newSMeter * 3) + 5) / 10);
+  
+      scaledSMeter = 0;
+      for (byte s = 8; s >= 1; s--) {
+        if (currentSMeter > sMeterLevels[s]) {
+          scaledSMeter = s;
+          break;
+        }
+      }
+  
+      DisplayMeter(0, scaledSMeter, 0);
+      checkCountSMeter = 0; //Reset Latency time
+    } //end of S-Meter
+    
+  }
+}
+
+//AutoKey LCD Display Routine
+void Display_AutoKeyTextIndex(byte textIndex)
+{
+  byte diplayAutoCWLine = 0;
+  
+  if ((displayOption1 & 0x01) == 0x01)
+    diplayAutoCWLine = 1;
+  LCD_SetCursor(0, diplayAutoCWLine);
+  LCD_Write(byteToChar(textIndex));
+  LCD_Write(':');
+}
+
+void DisplayCallsign(byte callSignLength)
+{
+  printLineFromEEPRom(3, 20 - userCallsignLength, 0, userCallsignLength -1, 0); //eeprom to lcd use offset (USER_CALLSIGN_DAT)
+}
+
+void DisplayVersionInfo(const __FlashStringHelper * fwVersionInfo)
+{
+  printLineF(3, fwVersionInfo);
+}
+
+#endif

ubitx_20/ubitx_si5351.ino

@@ -15,7 +15,6 @@
  ************************************************************************************/
 
 // *************  SI5315 routines - tks Jerry Gaffke, KE7ER   ***********************
-
 // An minimalist standalone set of Si5351 routines.
 // VCOA is fixed at 875mhz, VCOB not used.
 // The output msynth dividers are used to generate 3 independent clocks
@@ -127,7 +126,9 @@ void si5351_set_calibration(int32_t cal){
 void SetCarrierFreq()
 {
   unsigned long appliedCarrier = ((cwMode == 0 ? usbCarrier : cwmCarrier) + (isIFShift && (inTx == 0) ? ifShiftValue : 0));
-  si5351bx_setfreq(0, appliedCarrier);
+  //si5351bx_setfreq(0, (sdrModeOn ? 0 : appliedCarrier));
+  si5351bx_setfreq(0, ((sdrModeOn && (inTx == 0)) ? 0 : appliedCarrier)); //found bug by KG4GEK
+  
 
     /*
   if (cwMode == 0)

ubitx_20/ubitx_ui.ino

@@ -5,38 +5,9 @@
  * of the radio. Occasionally, it is used to provide a two-line information that is 
  * quickly cleared up.
  */
-//#define printLineF1(x) (printLineF(1, x))
-//#define printLineF2(x) (printLineF(0, x))
-
-//returns true if the button is pressed
-int btnDown(void){
-  if (digitalRead(FBUTTON) == HIGH)
-    return 0;
-  else
-    return 1;
-}
-
-/**
- * Meter (not used in this build for anything)
- * the meter is drawn using special characters. Each character is composed of 5 x 8 matrix.
- * The  s_meter array holds the definition of the these characters. 
- * each line of the array is is one character such that 5 bits of every byte 
- * makes up one line of pixels of the that character (only 5 bits are used)
- * The current reading of the meter is assembled in the string called meter
- */
 
 
 /*
-const PROGMEM uint8_t s_meter_bitmap[] = {
-  B00000,B00000,B00000,B00000,B00000,B00100,B00100,B11011,
-  B10000,B10000,B10000,B10000,B10100,B10100,B10100,B11011,
-  B01000,B01000,B01000,B01000,B01100,B01100,B01100,B11011,
-  B00100,B00100,B00100,B00100,B00100,B00100,B00100,B11011,
-  B00010,B00010,B00010,B00010,B00110,B00110,B00110,B11011,
-  B00001,B00001,B00001,B00001,B00101,B00101,B00101,B11011
-};
-*/
-
 const PROGMEM uint8_t meters_bitmap[] = {
   B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000 ,   //custom 1
   B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000 ,   //custom 2
@@ -45,7 +16,35 @@ const PROGMEM uint8_t meters_bitmap[] = {
   B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111 ,   //custom 5
   B01000,  B11100,  B01000,  B00000,  B10111,  B10101,  B10101,  B10111     //custom 6
 };
+*/
 
+//SWR GRAPH,  DrawMeter and drawingMeter Logic function by VK2ETA 
+
+#ifdef OPTION_SKINNYBARS //We want skninny bars with more text
+//VK2ETA modded "Skinny" bitmaps
+const PROGMEM uint8_t meters_bitmap[] = {
+  //  B01110, B10001, B10001, B11111, B11011, B11011, B11111, B00000, //Padlock Symbol, for merging. Not working, see below
+  B00000, B00000, B00000, B00000, B00000, B00000, B00000, B10000, //shortest bar
+  B00000, B00000, B00000, B00000, B00000, B00000, B00100, B10100,
+  B00000, B00000, B00000, B00000, B00000, B00001, B00101, B10101,
+  B00000, B00000, B00000, B00000, B10000, B10000, B10000, B10000,
+  B00000, B00000, B00000, B00100, B10100, B10100, B10100, B10100,
+  B00000, B00000, B00001, B00101, B10101, B10101, B10101, B10101, //tallest bar
+  B00000, B00010, B00111, B00010, B01000, B11100, B01000, B00000, // ++ sign
+};
+#else
+//VK2ETA "Fat" bars, easy to read, with less text
+const PROGMEM uint8_t meters_bitmap[] = {
+  //  B01110, B10001, B10001, B11111, B11011, B11011, B11111, B00000, //Padlock Symbol, for merging. Not working, see below
+  B00000, B00000, B00000, B00000, B00000, B00000, B00000, B11111, //shortest bar
+  B00000, B00000, B00000, B00000, B00000, B00000, B11111, B11111,
+  B00000, B00000, B00000, B00000, B00000, B11111, B11111, B11111,
+  B00000, B00000, B00000, B00000, B11111, B11111, B11111, B11111,
+  B00000, B00000, B00000, B11111, B11111, B11111, B11111, B11111,
+  B00000, B00000, B11111, B11111, B11111, B11111, B11111, B11111, //tallest bar
+  B00000, B00010, B00111, B00010, B01000, B11100, B01000, B00000, // ++ sign
+};
+#endif //OPTION_SKINNYBARS
 PGM_P p_metes_bitmap = reinterpret_cast<PGM_P>(meters_bitmap);
 
 const PROGMEM uint8_t lock_bitmap[8] = {
@@ -68,35 +67,41 @@ void initMeter(){
 
   for (i = 0; i < 8; i++)
     tmpbytes[i] = pgm_read_byte(plock_bitmap + i);
-  lcd.createChar(0, tmpbytes);
+  LCD_CreateChar(0, tmpbytes);
   
   for (i = 0; i < 8; i++)
     tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i);
-  lcd.createChar(1, tmpbytes);
+  LCD_CreateChar(1, tmpbytes);
 
   for (i = 0; i < 8; i++)
     tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 8);
-  lcd.createChar(2, tmpbytes);
+  LCD_CreateChar(2, tmpbytes);
   
   for (i = 0; i < 8; i++)
     tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 16);
-  lcd.createChar(3, tmpbytes);
+  LCD_CreateChar(3, tmpbytes);
   
   for (i = 0; i < 8; i++)
     tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 24);
-  lcd.createChar(4, tmpbytes);
+  LCD_CreateChar(4, tmpbytes);
   
   for (i = 0; i < 8; i++)
     tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 32);
-  lcd.createChar(5, tmpbytes);
+  LCD_CreateChar(5, tmpbytes);
   
   for (i = 0; i < 8; i++)
     tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 40);
-  lcd.createChar(6, tmpbytes);
+  LCD_CreateChar(6, tmpbytes);
+
+  for (i = 0; i < 8; i++)
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 48);
+  LCD_CreateChar(6, tmpbytes);
 }
 
+
 //by KD8CEC
 //0 ~ 25 : 30 over : + 10
+/*
 void drawMeter(int needle) {
   //5Char + O over
   int i;
@@ -117,217 +122,79 @@ void drawMeter(int needle) {
   else
     lcdMeter[5] = 0x20;
 }
-
-/*
-void drawMeter(int8_t needle){
-  int16_t best, i, s;
-
-  if (needle < 0)
-    return;
-
-  s = (needle * 4)/10;
-  for (i = 0; i < 8; i++){
-    if (s >= 5)
-      lcdMeter[i] = 1;
-    else if (s >= 0)
-      lcdMeter[i] = 2 + s;
-    else
-      lcdMeter[i] = 1;
-    s = s - 5;
-  }
-  if (needle >= 40)
-    lcdMeter[i-1] = 6;
-  lcdMeter[i] = 0;
-}
 */
-// The generic routine to display one line on the LCD 
-void printLine(unsigned char linenmbr, const char *c) {
-  if ((displayOption1 & 0x01) == 0x01)
-    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
-    
-  if (strcmp(c, printBuff[linenmbr])) {     // only refresh the display when there was a change
-    lcd.setCursor(0, linenmbr);             // place the cursor at the beginning of the selected line
-    lcd.print(c);
-    strcpy(printBuff[linenmbr], c);
-
-    for (byte i = strlen(c); i < 16; i++) { // add white spaces until the end of the 16 characters line is reached
-      lcd.print(' ');
+//VK2ETA meter for S.Meter, power and SWR
+void drawMeter(int needle) 
+{
+#ifdef OPTION_SKINNYBARS
+  //Fill buffer with growing set of bars, up to needle value
+  for (int i = 0; i < 6; i++) {
+    if (needle > i)
+      lcdMeter[i / 3] = byte(i + 1); //Custom characters above
+    else if (i == 1 || i == 4) {
+      lcdMeter[i / 3] = 0x20; //blank
     }
   }
-}
-
-void printLineF(char linenmbr, const __FlashStringHelper *c)
-{
-  int i;
-  char tmpBuff[17];
-  PGM_P p = reinterpret_cast<PGM_P>(c);  
-
-  for (i = 0; i < 17; i++){
-    unsigned char fChar = pgm_read_byte(p++);
-    tmpBuff[i] = fChar;
-    if (fChar == 0)
-      break;
-  }
-
-  printLine(linenmbr, tmpBuff);
-}
-
-#define LCD_MAX_COLUMN 16
-void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetTtype) {
-  if ((displayOption1 & 0x01) == 0x01)
-    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
-  
-  lcd.setCursor(lcdColumn, linenmbr);
-
-  for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
-  {
-    if (++lcdColumn <= LCD_MAX_COLUMN)
-      lcd.write(EEPROM.read((offsetTtype == 0 ? USER_CALLSIGN_DAT : WSPR_MESSAGE1) + i));
+#else //Must be "fat" bars
+  //Fill buffer with growing set of bars, up to needle value
+  for (int i = 0; i < 6; i++) {
+    if (needle > i)
+      lcdMeter[i] = byte(i + 1); //Custom characters above
     else
-      break;
+      lcdMeter[i] = 0x20; //blank
   }
-  
-  for (byte i = lcdColumn; i < 16; i++) //Right Padding by Space
-      lcd.write(' ');
+  if (needle > 7) {
+    lcdMeter[6] = byte(7); //Custom character "++"
+  } else if (needle > 6) {
+    lcdMeter[6] = 0x2B; //"+"
+  } else lcdMeter[6] = 0x20;
+#endif //OPTION_FATBARS
 }
 
-//  short cut to print to the first line
-void printLine1(const char *c){
-  printLine(1,c);
-}
-//  short cut to print to the first line
-void printLine2(const char *c){
-  printLine(0,c);
-}
 
-void clearLine2()
-{
-  printLine2("");
-  line2DisplayStatus = 0;
-}
 
-//  short cut to print to the first line
-void printLine1Clear(){
-  printLine(1,"");
-}
-//  short cut to print to the first line
-void printLine2Clear(){
-  printLine(0, "");
-}
-
-void printLine2ClearAndUpdate(){
-  printLine(0, "");
-  line2DisplayStatus = 0;  
-  updateDisplay();
-}
-
-//012...89ABC...Z
-char byteToChar(byte srcByte){
+ char byteToChar(byte srcByte){
   if (srcByte < 10)
     return 0x30 + srcByte;
  else
     return 'A' + srcByte - 10;
 }
 
-// this builds up the top line of the display with frequency and mode
-void updateDisplay() {
-  // tks Jack Purdum W8TEE
-  // replaced fsprint commmands by str commands for code size reduction
-  // replace code for Frequency numbering error (alignment, point...) by KD8CEC
-  int i;
-  unsigned long tmpFreq = frequency; //
-  
-  memset(c, 0, sizeof(c));
+//returns true if the button is pressed
+int btnDown(void){
+#ifdef EXTEND_KEY_GROUP1  
+  if (analogRead(FBUTTON) > FUNCTION_KEY_ADC)
+    return 0;
+  else
+    return 1;
 
-  if (inTx){
-    if (isCWAutoMode == 2) {
-      for (i = 0; i < 4; i++)
-        c[3-i] = (i < autoCWSendReservCount ? byteToChar(autoCWSendReserv[i]) : ' ');
+#else
+  if (digitalRead(FBUTTON) == HIGH)
+    return 0;
+  else
+    return 1;
+#endif    
+}
 
-      //display Sending Index
-      c[4] = byteToChar(sendingCWTextIndex);
-      c[5] = '=';
-    }
-    else {
-      if (cwTimeout > 0)
-        strcpy(c, "   CW:");
-      else
-        strcpy(c, "   TX:");
-    }
-  }
-  else {
-    if (ritOn)
-      strcpy(c, "RIT ");
-    else {
-      if (cwMode == 0)
-      {
-        if (isUSB)
-          strcpy(c, "USB ");
-        else
-          strcpy(c, "LSB ");
-      }
-      else if (cwMode == 1)
-      {
-          strcpy(c, "CWL ");
-      }
-      else
-      {
-          strcpy(c, "CWU ");
-      }
-    }
-    if (vfoActive == VFO_A) // VFO A is active
-      strcat(c, "A:");
-    else
-      strcat(c, "B:");
-  }
+#ifdef EXTEND_KEY_GROUP1  
+int getBtnStatus(void){
+  int readButtonValue = analogRead(FBUTTON);
 
-  //Fixed by Mitani Massaru (JE4SMQ)
-  if (isShiftDisplayCWFreq == 1)
-  {
-    if (cwMode == 1)        //CWL
-        tmpFreq = tmpFreq - sideTone + shiftDisplayAdjustVal;
-    else if (cwMode == 2)   //CWU
-        tmpFreq = tmpFreq + sideTone + shiftDisplayAdjustVal;
-  }
-
-  //display frequency
-  for (int i = 15; i >= 6; i--) {
-    if (tmpFreq > 0) {
-      if (i == 12 || i == 8) c[i] = '.';
-      else {
-        c[i] = tmpFreq % 10 + 0x30;
-        tmpFreq /= 10;
-      }
-    }
-    else
-      c[i] = ' ';
-  }
-
-  //remarked by KD8CEC
-  //already RX/TX status display, and over index (16 x 2 LCD)
-  //if (inTx)
-  //  strcat(c, " TX");
-  printLine(1, c);
-
-  byte diplayVFOLine = 1;
-  if ((displayOption1 & 0x01) == 0x01)
-    diplayVFOLine = 0;
-
-  if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
-    (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02))) {
-    lcd.setCursor(5,diplayVFOLine);
-    lcd.write((uint8_t)0);
-  }
-  else if (isCWAutoMode == 2){
-    lcd.setCursor(5,diplayVFOLine);
-    lcd.write(0x7E);
-  }
+  if (analogRead(FBUTTON) < FUNCTION_KEY_ADC)
+    return FKEY_PRESS;
   else
   {
-    lcd.setCursor(5,diplayVFOLine);
-    lcd.write(":");
+    readButtonValue = readButtonValue / 4;
+    //return FKEY_VFOCHANGE;
+    for (int i = 0; i < 16; i++)
+      if (KeyValues[i][0] <= readButtonValue && KeyValues[i][1] >= readButtonValue)
+        return KeyValues[i][2];
+        //return i;
   }
+
+  return -1;
 }
+#endif
 
 int enc_prev_state = 3;
 

ubitx_20/ubitx_wspr.ino

@@ -23,21 +23,19 @@ Beta Tester :
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
 **********************************************************************************/
 
-#include <arduino.h>
 #include <EEPROM.h>
 #include "ubitx.h"
 
 //begin of test
 byte WsprToneCode[164];
 
-long lastTime=0;
+unsigned long lastTime=0;
 unsigned long TX_MSNB_P2;              // Si5351 register MSNB_P2  PLLB for Tx
 unsigned long TX_P2;    // Variable values for MSNB_P2 which defines the frequencies for the data
 
 extern int enc_read(void);
 
 byte WsprMSGCount = 0;
-#define PTT   (A3)
 
 #define WSPR_BAND1 401
 
@@ -48,7 +46,7 @@ void SendWSPRManage()
 {
   int knob = 0;
   byte knobPosition = 0;
-  char isNeedDisplayInfo = 0;
+  //char isNeedDisplayInfo = 0;
   char nowSelectedIndex = 0;
   char nowWsprStep = 0; //0 : select Message, 1 : select band, 2 : send
   char selectedWsprMessageIndex = -1;
@@ -56,8 +54,8 @@ void SendWSPRManage()
 
   unsigned long WsprTXFreq = 0;
   unsigned int WsprMultiChan = 0;
-  unsigned long prevFreq;
-  char loopIndex;
+  //unsigned long prevFreq;
+  byte loopIndex;
 
   delay_background(500, 0);