fixed cat with cw key (IA, IB)

README.md

@@ -1,11 +1,7 @@
 #IMPORTANT INFORMATION
 ----------------------------------------------------------------------------
-- 0.30 Version Test only download. almost complete
-- Beta 0.26 and Beta 0.261, Beta 0.262,0.27 is complete test, 0.28 is tested.
-- You can download and use it (Release section).
-
-# Current work list (for Version 0.31)
-  1 Testing CAT Control with Software using hamlib on Linux
+- Beta 0.26 and Beta 0.261, Beta 0.262, Beta 0.27 is complete test
+- You can download and use it.
 
 #NOTICE
 ----------------------------------------------------------------------------
@@ -50,24 +46,6 @@ Prepared or finished tasks for the next version
                   
 ----------------------------------------------------------------------------
 ## REVISION RECORD
-0.30
- - implemented the function to monitor the value of all analog inputs. This allows you to monitor the status of the CW keys connected to your uBITX. 
- - possible to set the ADC range for CW Keying. If no setting is made, it will have the same range as the original code. If you set the CW Keying ADC Values using uBITX Manager 0.3, you can reduce the key error.
- - Added the function to select Straight Key, IAMBICA, IAMBICB key from the menu.
- - default Band select is Ham Band mode, if you want common type, long press function key at band select menu, uBITX Manager can be used to modify frequencies to suit your country.
-
-0.29
- - Remove the use of initialization values in BFO settings - using crruent value, if factory reset
- - Select Tune Step, default 0, 20, 50, 100, 200, Use the uBITX Manager to set the steps value you want. You can select Step by pressing and holding the Function Key (1sec ~ 2sec).
- - Modify Dial Lock Function, Press the Function key for more than 3 seconds to toggle dial lock.
- - created a new frequency tune method. remove original source codes, Threshold has been applied to reduce malfunction. checked the continuity of the user operating to make natural tune possible.
- - stabilize and remove many warning messages - by Pullrequest and merge
- - Changed cw keying method. removed the original code and applied Ron's code and Improved compatibility with original hardware and CAT commnication. It can be used without modification of hardware.
- 
-0.28
- - Fixed CAT problem with hamlib on Linux
- - restore Protocol autorecovery logic
-
 0.27 
    (First alpha test version, This will be renamed to the major version 1.0)
  - Dual VFO Dial Lock (vfoA Dial lock)

ubitx_20/cat_libs.ino

@@ -109,7 +109,8 @@ void CatSetFreq(byte fromType)
 //#define BCD_LEN 9
 //PROTOCOL : 0x03
 //Computer <-(frequency)-> TRCV CAT_BUFF
-void CatGetFreqMode(unsigned long freq, byte fromType)
+//void CatGetFreqMode(unsigned long freq, byte fromType)
+void CatGetFreqMode(unsigned long freq) //for remove warning messages
 {
   int i;
   byte tmpValue;
@@ -130,23 +131,40 @@ void CatGetFreqMode(unsigned long freq, byte fromType)
   }
 
   //Mode Check
-  if (isUSB)
-    CAT_BUFF[4] = CAT_MODE_USB;
+  if (cwMode == 0)
+  {
+    if (isUSB)
+      CAT_BUFF[4] = CAT_MODE_USB;
+    else
+      CAT_BUFF[4] = CAT_MODE_LSB;
+  }
+  else if (cwMode == 1)
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
   else
-    CAT_BUFF[4] = CAT_MODE_LSB;
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
 
   SendCatData(5);
 }
 
-void CatSetSplit(boolean isSplit, byte fromType)
+//void CatSetSplit(boolean isSplit, byte fromType)
+void CatSetSplit(boolean isSplit) //for remove warning messages
 {
-
+  if (isSplit)
+    splitOn = 1;
+  else
+    splitOn = 0;
+    
   Serial.write(ACK);
 }
 
 void CatSetPTT(boolean isPTTOn, byte fromType)
 {
-  if (fromType == 2 || fromType == 3) {
+  //
+  if ((!inTx) && (fromType == 2 || fromType == 3)) {
     Serial.write(ACK);  
     return;  
   }
@@ -182,7 +200,7 @@ void CatSetPTT(boolean isPTTOn, byte fromType)
 void CatVFOToggle(boolean isSendACK, byte fromType)
 {
   if (fromType != 2 && fromType != 3) {
-    menuVfoToggle(1, 0);
+    menuVfoToggle(1);
   }  
 
   if (isSendACK)
@@ -198,12 +216,18 @@ void CatSetMode(byte tmpMode, byte fromType)
   
   if (!inTx)
   {
-    if (tmpMode == CAT_MODE_USB)
+    if (tmpMode == CAT_MODE_CW)
     {
+      cwMode = 1;
+    }
+    else if (tmpMode == CAT_MODE_USB)
+    {
+      cwMode = 0;
       isUSB = true;
     }
     else
     {
+      cwMode = 0;
       isUSB = false;
     }
 
@@ -215,7 +239,8 @@ void CatSetMode(byte tmpMode, byte fromType)
 }
 
 //Read EEProm by uBITX Manager Software
-void ReadEEPRom(byte fromType)
+//void ReadEEPRom(byte fromType)
+void ReadEEPRom() //for remove warnings.
 {
   //5BYTES
   //CAT_BUFF[0] [1] [2] [3] [4] //4 COMMAND
@@ -238,7 +263,8 @@ void ReadEEPRom(byte fromType)
 }
 
 //Write just proecess 1byes
-void WriteEEPRom(byte fromType)
+//void WriteEEPRom(byte fromType)
+void WriteEEPRom(void)  //for remove warning
 {
   //5BYTES
   uint16_t eepromStartIndex = CAT_BUFF[0] + CAT_BUFF[1] * 256;
@@ -258,7 +284,8 @@ void WriteEEPRom(byte fromType)
   }
 }
 
-void ReadEEPRom_FT817(byte fromType)
+//void ReadEEPRom_FT817(byte fromType)
+void ReadEEPRom_FT817(void) //for remove warnings
 {
   byte temp0 = CAT_BUFF[0];
   byte temp1 = CAT_BUFF[1];
@@ -358,10 +385,21 @@ void ReadEEPRom_FT817(byte fromType)
       CAT_BUFF[1] = 0xB2;
       break;      case 0x69 : //FM Mic (#29)  Contains 0-100 (decimal) as displayed
     case 0x78 :
-      if (isUSB)
-        CAT_BUFF[0] = CAT_MODE_USB;
-      else
-        CAT_BUFF[0] = CAT_MODE_LSB;
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          CAT_BUFF[0] = CAT_MODE_USB;
+        else
+          CAT_BUFF[0] = CAT_MODE_LSB;
+      }
+      else if (cwMode == 1)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
+      else if (cwMode == 2)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
         
       if (CAT_BUFF[0] != 0) CAT_BUFF[0] = 1 << 5;
       break;
@@ -384,7 +422,7 @@ void ReadEEPRom_FT817(byte fromType)
       //7A  6 ? ?
       //7A  7 SPL On/Off  0 = Off, 1 = On
 
-      CAT_BUFF[0] = (isSplitOn ? 0xFF : 0x7F);
+      CAT_BUFF[0] = (splitOn ? 0xFF : 0x7F);
       break;
     case 0xB3 : //
       CAT_BUFF[0] = 0x00;
@@ -573,7 +611,8 @@ void WriteEEPRom_FT817(byte fromType)
   Serial.write(ACK);
 }
 
-void CatRxStatus(byte fromType) 
+//void CatRxStatus(byte fromType) 
+void CatRxStatus(void)  //for remove warning
 {
   byte sMeterValue = 1;
 
@@ -593,7 +632,8 @@ void CatRxStatus(byte fromType)
 }
 
 
-void CatTxStatus(byte fromType)
+//void CatTxStatus(byte fromType)
+void CatTxStatus(void)  //for remove warning
 {
   boolean isHighSWR = false;
   boolean isSplitOn = false;
@@ -694,11 +734,11 @@ void Check_Cat(byte fromType)
       
     case 0x02 : //Split On
     case 0x82:  //Split Off
-      CatSetSplit(CAT_BUFF[4] == 0x02, fromType);
+      CatSetSplit(CAT_BUFF[4] == 0x02);
       break;
 
     case 0x03 :   //Read Frequency and mode
-      CatGetFreqMode(frequency, fromType);
+      CatGetFreqMode(frequency);
       break;
 
     case 0x07 :   //Set Operating  Mode
@@ -715,24 +755,24 @@ void Check_Cat(byte fromType)
       break;
 
     case 0xDB:  //Read uBITX EEPROM Data
-      ReadEEPRom(fromType); //Call by uBITX Manager Program
+      ReadEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBB:  //Read FT-817 EEPROM Data  (for comfirtable)
-      ReadEEPRom_FT817(fromType);
+      ReadEEPRom_FT817();
       break;
 
     case 0xDC:  //Write uBITX EEPROM Data
-      WriteEEPRom(fromType); //Call by uBITX Manager Program
+      WriteEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBC:  //Write FT-817 EEPROM Data  (for comfirtable)
       WriteEEPRom_FT817(fromType);
       break;
 
     case 0xE7 :       //Read RX Status
-      CatRxStatus(fromType);
+      CatRxStatus();
       break;
     case 0xF7:      //Read TX Status
-      CatTxStatus(fromType);
+      CatTxStatus();
       break;
     default:
     /*

ubitx_20/cw_autokey.ino

@@ -365,6 +365,11 @@ void controlAutoCW(){
         //check interval time, if you want adjust interval between chars, modify below
         if (isAutoCWHold == 0 && (millis() - autoCWbeforeTime > cwSpeed * 3))
         {
+          if (!inTx){                                           //if not TX Status, change RX -> TX
+            keyDown = 0;
+            startTx(TX_CW, 0);  //disable updateDisplay Command for reduce latency time
+          }
+          
           sendCWChar(EEPROM.read(CW_AUTO_DATA + autoCWSendCharIndex++));
 
           if (autoCWSendCharIndex > autoCWSendCharEndIndex) {          //finish auto cw send

ubitx_20/ubitx_20.ino

@@ -151,15 +151,17 @@ int count = 0;          //to generally count ticks, loops, etc
 #define CW_SPEED 28
 
 //AT328 has 1KBytes EEPROM
+#define CW_CAL 252
 #define VFO_A_MODE 256
 #define VFO_B_MODE 257
 #define CW_DELAY 258
 #define CW_START 259
-#define HAM_BAND_COUNT 260  //
-#define TX_TUNE_TYPE 261  //
-#define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
-#define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)
+#define HAM_BAND_COUNT 260    //
+#define TX_TUNE_TYPE 261      //
+#define HAM_BAND_RANGE 262    //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
+#define HAM_BAND_FREQS 302    //40, 1 BAND = 4Byte most bit is mode
+#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+  
 
 //for reduce cw key error, eeprom address
 #define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
@@ -178,6 +180,10 @@ int count = 0;          //to generally count ticks, loops, etc
 #define DISPLAY_OPTION1  361   //Display Option1
 #define DISPLAY_OPTION2  362   //Display Option2
 
+#define CHANNEL_FREQ    630   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define CHANNEL_DESC    710   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define RESERVE3        770   //Reserve3 between Channel and Firmware id check
+
 //Check Firmware type and version
 #define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
 #define VERSION_ADDRESS 779   //check Firmware version
@@ -232,7 +238,7 @@ int count = 0;          //to generally count ticks, loops, etc
 char ritOn = 0;
 char vfoActive = VFO_A;
 int8_t meter_reading = 0; // a -1 on meter makes it invisible
-unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier;
+unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier, cwmCarrier;
 unsigned long vfoA_eeprom, vfoB_eeprom; //for protect eeprom life
 unsigned long frequency, ritRxFrequency, ritTxFrequency;  //frequency is the current frequency on the dial
 
@@ -249,7 +255,6 @@ byte saveIntervalSec = 10;  //second
 unsigned long saveCheckTime = 0;
 unsigned long saveCheckFreq = 0;
 
-bool isSplitOn = false;
 byte cwDelayTime = 60;
 byte delayBeforeCWStartTime = 50;
 
@@ -260,7 +265,7 @@ byte sideToneSub = 0;
 //DialLock
 byte isDialLock = 0;  //000000[0]vfoB [0]vfoA 0Bit : A, 1Bit : B
 byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
-byte arTuneStep[5];
+long arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
 byte displayOption1 = 0;
@@ -298,9 +303,13 @@ byte userCallsignLength = 0;    //7 : display callsign at system startup, 6~0 :
  */
 boolean txCAT = false;        //turned on if the transmitting due to a CAT command
 char inTx = 0;                //it is set to 1 if in transmit mode (whatever the reason : cw, ptt or cat)
-char splitOn = 0;             //working split, uses VFO B as the transmit frequency, (NOT IMPLEMENTED YET)
+char splitOn = 0;             //working split, uses VFO B as the transmit frequency
 char keyDown = 0;             //in cw mode, denotes the carrier is being transmitted
 char isUSB = 0;               //upper sideband was selected, this is reset to the default for the 
+
+char cwMode = 0;              //compatible original source, and extend mode //if cwMode == 0, mode check : isUSB, cwMode > 0, mode Check : cwMode
+                              //iscwMode = 0 : ssbmode, 1 :cwl, 2 : cwu, 3 : cwn (none tx)
+                              
                               //frequency when it crosses the frequency border of 10 MHz
 byte menuOn = 0;              //set to 1 when the menu is being displayed, if a menu item sets it to zero, the menu is exited
 unsigned long cwTimeout = 0;  //milliseconds to go before the cw transmit line is released and the radio goes back to rx mode
@@ -311,6 +320,10 @@ boolean modeCalibrate = false;//this mode of menus shows extended menus to calib
 
 unsigned long beforeIdle_ProcessTime = 0; //for check Idle time
 byte line2DisplayStatus = 0;  //0:Clear, 1 : menu, 1: DisplayFrom Idle, 
+char lcdMeter[17];
+
+byte isIFShift = 0;     //1 = ifShift, 2 extend
+long ifShiftValue = 0;  //
                               
 /**
  * Below are the basic functions that control the uBitx. Understanding the functions before 
@@ -364,22 +377,24 @@ void setNextHamBandFreq(unsigned long f, char moveDirection)
 
   EEPROM.get(HAM_BAND_FREQS + 4 * findedIndex, resultFreq);
   
-  loadMode = (byte)(resultFreq >> 30);
-  resultFreq = resultFreq & 0x3FFFFFFF;
+  //loadMode = (byte)(resultFreq >> 30);
+  //resultFreq = resultFreq & 0x3FFFFFFF;
+  loadMode = (byte)(resultFreq >> 29);
+  resultFreq = resultFreq & 0x1FFFFFFF;
   
   if ((resultFreq / 1000) < hamBandRange[(unsigned char)findedIndex][0] || (resultFreq / 1000) > hamBandRange[(unsigned char)findedIndex][1])
     resultFreq = (unsigned long)(hamBandRange[(unsigned char)findedIndex][0]) * 1000;
 
   setFrequency(resultFreq);
-  byteWithFreqToMode(loadMode);
+  byteToMode(loadMode, 1);
 }
 
 void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
   if (bandIndex >= 0)
-    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    //EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x1FFFFFFF) | (mode << 29) );
 }
 
-
 /*
   KD8CEC
   When using the basic delay of the Arduino, the program freezes.
@@ -473,13 +488,27 @@ void setFrequency(unsigned long f){
   
   setTXFilters(f);
 
-  if (isUSB){
-    si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_USB);
+  if (cwMode == 0)
+  {
+    if (isUSB){
+      si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f  + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
+    else{
+      si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
   }
-  else{
-    si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_LSB);
+  else
+  {
+    if (cwMode == 1){ //CWL
+      si5351bx_setfreq(2, SECOND_OSC_LSB + cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
+    else{             //CWU
+      si5351bx_setfreq(2, SECOND_OSC_USB - cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
   }
   
   frequency = f;
@@ -508,6 +537,21 @@ void startTx(byte txMode, byte isDisplayUpdate){
     ritRxFrequency = frequency;
     setFrequency(ritTxFrequency);
   }
+  else if (splitOn == 1) {
+      if (vfoActive == VFO_B) {
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+
+      setFrequency(frequency);
+  } //end of else
+  
 
   if (txMode == TX_CW){
     //turn off the second local oscillator and the bfo
@@ -517,10 +561,22 @@ void startTx(byte txMode, byte isDisplayUpdate){
     //shif the first oscillator to the tx frequency directly
     //the key up and key down will toggle the carrier unbalancing
     //the exact cw frequency is the tuned frequency + sidetone
-    if (isUSB)
-      si5351bx_setfreq(2, frequency + sideTone);
-    else
-      si5351bx_setfreq(2, frequency - sideTone); 
+
+    if (cwMode == 0)
+    {
+      if (isUSB)
+        si5351bx_setfreq(2, frequency + sideTone);
+      else
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else if (cwMode == 1) //CWL
+    {
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else  //CWU
+    {
+        si5351bx_setfreq(2, frequency + sideTone);
+    }
   }
 
   //reduce latency time when begin of CW mode
@@ -532,10 +588,28 @@ void stopTx(){
   inTx = 0;
 
   digitalWrite(TX_RX, 0);           //turn off the tx
-  si5351bx_setfreq(0, usbCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
+  else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
 
   if (ritOn)
     setFrequency(ritRxFrequency);
+  else if (splitOn == 1) {
+      //vfo Change
+      if (vfoActive == VFO_B){
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+      setFrequency(frequency);
+  } //end of else
   else
     setFrequency(frequency);
   
@@ -622,7 +696,6 @@ byte lastMovedirection = 0; //0 : stop, 1 : cw, 2 : ccw
 void doTuningWithThresHold(){
   int s = 0;
   unsigned long prev_freq;
-  long incdecValue = 0;
 
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02)))
@@ -685,9 +758,8 @@ void doRIT(){
     updateDisplay();
   }
 }
-
-/**
- save Frequency and mode to eeprom
+/*
+ save Frequency and mode to eeprom for Auto Save with protected eeprom cycle, by kd8cec
  */
 void storeFrequencyAndMode(byte saveType)
 {
@@ -719,6 +791,22 @@ void storeFrequencyAndMode(byte saveType)
   }
 }
 
+//calculate step size from 1 byte, compatible uBITX Manager, by KD8CEC
+unsigned int byteToSteps(byte srcByte) {
+    byte powerVal = (byte)(srcByte >> 6);
+    unsigned int baseVal = srcByte & 0x3F;
+
+    if (powerVal == 1)
+        return baseVal * 10;
+    else if (powerVal == 2)
+        return baseVal * 100;
+    else if (powerVal == 3)
+        return baseVal * 1000;
+    else
+        return baseVal;
+}
+
+
 /**
  * The settings are read from EEPROM. The first time around, the values may not be 
  * present or out of range, in this case, some intelligent defaults are copied into the 
@@ -761,6 +849,7 @@ void initSettings(){
   if (EEPROM.read(VERSION_ADDRESS) != VERSION_NUM)
     EEPROM.write(VERSION_ADDRESS, VERSION_NUM);
 
+  EEPROM.get(CW_CAL, cwmCarrier);
 
   //for Save VFO_A_MODE to eeprom
   //0: default, 1:not use, 2:LSB, 3:USB, 4:CW, 5:AM, 6:FM
@@ -781,7 +870,7 @@ void initSettings(){
   else
   {
     Iambic_Key = true;
-    if (cwKeyType = 1)
+    if (cwKeyType == 1)
       keyerControl &= ~IAMBICB;
     else
       keyerControl |= IAMBICB;
@@ -818,13 +907,13 @@ void initSettings(){
   if ((3 < tuneTXType && tuneTXType < 100) || 103 < tuneTXType || useHamBandCount < 1 || findedValidValueCount < 5)
   {
     tuneTXType = 2;
-    //if empty band Information, auto insert default region 1 frequency range
+    //if empty band Information, auto insert default region 2 frequency range
     //This part is made temporary for people who have difficulty setting up, so can remove it when you run out of memory.
     useHamBandCount = 10;
     hamBandRange[0][0] = 1810; hamBandRange[0][1] = 2000; 
     hamBandRange[1][0] = 3500; hamBandRange[1][1] = 3800; 
     hamBandRange[2][0] = 5351; hamBandRange[2][1] = 5367; 
-    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7200; 
+    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;     //region 2
     hamBandRange[4][0] = 10100; hamBandRange[4][1] = 10150; 
     hamBandRange[5][0] = 14000; hamBandRange[5][1] = 14350; 
     hamBandRange[6][0] = 18068; hamBandRange[6][1] = 18168; 
@@ -838,8 +927,8 @@ void initSettings(){
   findedValidValueCount = 0;
   EEPROM.get(TUNING_STEP, tuneStepIndex);
   for (byte i = 0; i < 5; i++) {
-    arTuneStep[i] = EEPROM.read(TUNING_STEP + i + 1);
-    if (arTuneStep[i] >= 1 && arTuneStep[i] < 251) //Maximum 250 for check valid Value
+    arTuneStep[i] = byteToSteps(EEPROM.read(TUNING_STEP + i + 1));
+    if (arTuneStep[i] >= 1 && arTuneStep[i] <= 60000) //Maximum 650 for check valid Value
        findedValidValueCount++;
   }
 
@@ -909,15 +998,18 @@ void initSettings(){
   //original code with modified by kd8cec
   if (usbCarrier > 12010000l || usbCarrier < 11990000l)
     usbCarrier = 11995000l;
+
+  if (cwmCarrier > 12010000l || cwmCarrier < 11990000l)
+    cwmCarrier = 11995000l;
     
   if (vfoA > 35000000l || 3500000l > vfoA) {
      vfoA = 7150000l;
-     vfoA_mode = 2;
+     vfoA_mode = 2; //LSB
   }
   
   if (vfoB > 35000000l || 3500000l > vfoB) {
      vfoB = 14150000l;  
-     vfoB_mode = 3;
+     vfoB_mode = 3; //USB
   }
   //end of original code section
 
@@ -993,7 +1085,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.31")); 
+  printLineF(1, F("CECBT v1.01")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -1011,11 +1103,12 @@ void setup()
   }
   
   initPorts();     
+
+  byteToMode(vfoA_mode, 0);
   initOscillators();
 
   frequency = vfoA;
   saveCheckFreq = frequency;  //for auto save frequency
-  byteToMode(vfoA_mode);
   setFrequency(vfoA);
   updateDisplay();
 
@@ -1024,13 +1117,11 @@ void setup()
 }
 
 
-/**
- * The loop checks for keydown, ptt, function button and tuning.
- */
 //for debug
 int dbgCnt = 0;
 byte flasher = 0;
 
+//Auto save Frequency and Mode with Protected eeprom life by KD8CEC
 void checkAutoSaveFreqMode()
 {
   //when tx or ritOn, disable auto save
@@ -1048,6 +1139,7 @@ void checkAutoSaveFreqMode()
     //check time for Frequency auto save
     if (millis() - saveCheckTime > saveIntervalSec * 1000)
     {
+      /*
       if (vfoActive == VFO_A)
       {
         vfoA = frequency;
@@ -1060,6 +1152,8 @@ void checkAutoSaveFreqMode()
         vfoB_mode = modeToByte();
         storeFrequencyAndMode(2);
       }
+      */
+      FrequencyToVFO(1);
     }
   }
 }
@@ -1079,10 +1173,12 @@ void loop(){
   if (!inTx){
     if (ritOn)
       doRIT();
+    //else if (isIFShift)
+    //  doIFShift();
     else 
       doTuningWithThresHold();
 
-    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 200) {
+    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 250) {
       idle_process();
       beforeIdle_ProcessTime = millis();
     }

ubitx_20/ubitx_factory_alignment.ino

@@ -37,6 +37,7 @@ void factory_alignment(){
 
   
   printLine2("#3:Test 3.5MHz");
+  cwMode = 0;
   isUSB = false;
   setFrequency(3500000l);
   updateDisplay();
@@ -59,6 +60,7 @@ void factory_alignment(){
   btnWaitForClick();
   printLine2("#5:Test 14MHz");
 
+  cwMode = 0;
   isUSB = true;
   setFrequency(14000000l);
   updateDisplay();
@@ -80,6 +82,7 @@ void factory_alignment(){
   printLine2("Alignment done");
   delay(1000);
 
+  cwMode = 0;
   isUSB = false;
   setFrequency(7150000l);
   updateDisplay();  

ubitx_20/ubitx_idle.ino

@@ -17,14 +17,243 @@
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 **************************************************************************/
+char line2Buffer[16];
+//KD8CEC 200Hz ST
+//L14.150 200Hz ST
+//U14.150 +150khz
+int freqScrollPosition = 0;
+//Example Line2 Optinal Display
+//immediate execution, not call by scheulder
+void updateLine2Buffer(char isDirectCall)
+{
+  unsigned long tmpFreq = 0;
+  if (isDirectCall == 0)
+  {
+    if (ritOn)
+    {
+      line2Buffer[0] = 'R';
+      line2Buffer[1] = 'i';
+      line2Buffer[2] = 't';
+      line2Buffer[3] = 'T';
+      line2Buffer[4] = 'X';
+      line2Buffer[5] = ':';
+  
+      //display frequency
+      tmpFreq = ritTxFrequency;
+      for (int i = 15; i >= 6; i--) {
+        if (tmpFreq > 0) {
+          if (i == 12 || i == 8) line2Buffer[i] = '.';
+          else {
+            line2Buffer[i] = tmpFreq % 10 + 0x30;
+            tmpFreq /= 10;
+          }
+        }
+        else
+          line2Buffer[i] = ' ';
+      }
+  
+      return;
+    } //end of ritOn display
 
+    //======================================================
+    //other VFO display
+    //======================================================
+    if (vfoActive == VFO_B)
+    {
+      tmpFreq = vfoA;
+      //line2Buffer[0] = 'A';
+    }
+    else 
+    {
+      tmpFreq = vfoB;
+      //line2Buffer[0] = 'B';
+    }
+  
+    // EXAMPLE 1 & 2
+    //U14.150.100
+    //display frequency
+    for (int i = 9; i >= 0; i--) {
+      if (tmpFreq > 0) {
+        if (i == 2 || i == 6) line2Buffer[i] = '.';
+        else {
+          line2Buffer[i] = tmpFreq % 10 + 0x30;
+          tmpFreq /= 10;
+        }
+      }
+      else
+        line2Buffer[i] = ' ';
+    }
+  
+    //EXAMPLE #1
+    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
+      line2Buffer[6] = 'k';
+    else
+    {
+      //example #2
+      if (freqScrollPosition++ > 18)    //none scroll display time
+      {
+        line2Buffer[6] = 'k';
+        if (freqScrollPosition > 25)
+          freqScrollPosition = -1;
+      }
+      else                              //scroll frequency 
+      {
+        line2Buffer[10] = 'H';
+        line2Buffer[11] = 'z';
+    
+        if (freqScrollPosition < 7)   
+        {
+          for (int i = 11; i >= 0; i--)
+            if (i - (7 - freqScrollPosition) >= 0)
+              line2Buffer[i] = line2Buffer[i - (7 - freqScrollPosition)];
+            else
+              line2Buffer[i] = ' ';
+        }
+        else
+        {
+          for (int i = 0; i < 11; i++)
+            if (i + (freqScrollPosition - 7) <= 11)
+              line2Buffer[i] = line2Buffer[i + (freqScrollPosition - 7)];
+            else
+              line2Buffer[i] = ' ';
+        }
+      }
+    } //scroll
+    
+    line2Buffer[7] = ' ';
+  } //check direct call by encoder
+  
+  if (isIFShift)
+  {
+    if (isDirectCall == 1)
+      for (int i = 0; i < 16; i++)
+        line2Buffer[i] = ' ';
+      
+      //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
 
+    if (ifShiftValue == 0)
+    {
+      line2Buffer[10] = 'S';
+      line2Buffer[11] = ':';
+      line2Buffer[12] = 'O';
+      line2Buffer[13] = 'F';
+      line2Buffer[14] = 'F';
+    }
+    else
+    {
+      line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+      line2Buffer[11] = 0;
+      line2Buffer[12] = ' ';
+    
+      //11, 12, 13, 14, 15
+      memset(b, 0, sizeof(b));
+      ltoa(ifShiftValue, b, DEC);
+      strncat(line2Buffer, b, 5);
+    }
+    
+    if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
+        printLine2(line2Buffer);    
+  }       // end of display IF
+  else    // step display
+  {
+    if (isDirectCall != 0)
+      return;
+
+    memset(&line2Buffer[8], ' ', 8);
+    //Step
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
+      if (tmpStep > 0) {
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
+          tmpStep /= 10;
+      }
+      else
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+    //if (isStepKhz == 1)
+    //  line2Buffer[10] = 'k';
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[11] = 'H';
+      line2Buffer[12] = 'z';
+    }
+  
+    line2Buffer[13] = ' ';
+    //if (
+    //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+    if (cwKeyType == 0)
+    {
+      line2Buffer[14] = 'S';
+      line2Buffer[15] = 'T';
+    }
+    else if (cwKeyType == 1)
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'A';
+    }
+    else
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'B';
+    }    
+  }
+  
+}
+
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  if (meterType == 0 || meterType == 1 || meterType == 2)
+  {
+    drawMeter(meterValue);  //call original source code
+    int lineNumber = 0;
+    if ((displayOption1 & 0x01) == 0x01)
+      lineNumber = 1;
+    
+    lcd.setCursor(drawPosition, lineNumber);
+  
+    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+      lcd.write(lcdMeter[i]);
+  }
+}
+
+byte testValue = 0;
+char checkCount = 0;
 void idle_process()
 {
   //space for user graphic display
   if (menuOn == 0)
   {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
     //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
+    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
+        printLine2(line2Buffer);
+        line2DisplayStatus = 2;
+        checkCount = 0;
+      }
+
+      //EX for Meters
+      /*
+      DisplayMeter(0, testValue++, 7);
+      if (testValue > 30)
+        testValue = 0;
+      */
+    }
   }
 }
 

ubitx_20/ubitx_keyer.ino

@@ -90,13 +90,13 @@ void cwKeyUp(){
 #define PDLSWAP 0x08 // 0 for normal, 1 for swap
 #define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
 enum KSTYPE {IDLE, CHK_DIT, CHK_DAH, KEYED_PREP, KEYED, INTER_ELEMENT };
-static long ktimer;
+static unsigned long ktimer;
 unsigned char keyerState = IDLE;
 
 //Below is a test to reduce the keying error. do not delete lines
 //create by KD8CEC for compatible with new CW Logic
 char update_PaddleLatch(byte isUpdateKeyState) {
-  unsigned char tmpKeyerControl;
+  unsigned char tmpKeyerControl = 0;
   int paddle = analogRead(ANALOG_KEYER);
 
   if (paddle >= cwAdcDashFrom && paddle <= cwAdcDashTo)
@@ -126,9 +126,7 @@ char update_PaddleLatch(byte isUpdateKeyState) {
 // modified by KD8CEC
 ******************************************************************************/
 void cwKeyer(void){
-  byte paddle;
   lastPaddle = 0;
-  int dot,dash;
   bool continue_loop = true;
   unsigned tmpKeyControl = 0;
   
@@ -206,7 +204,7 @@ void cwKeyer(void){
           break;
       }
   
-      Check_Cat(3);
+      Check_Cat(2);
     } //end of while
   }
   else{

ubitx_20/ubitx_si5351.ino

@@ -109,7 +109,11 @@ void initOscillators(){
   //initialize the SI5351
   si5351bx_init();
   si5351bx_vcoa = (SI5351BX_XTAL * SI5351BX_MSA) + calibration; // apply the calibration correction factor
-  si5351bx_setfreq(0, usbCarrier);
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));
+ else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));
 }
 
 

ubitx_20/ubitx_ui.ino

@@ -25,8 +25,8 @@ int btnDown(){
  * The current reading of the meter is assembled in the string called meter
  */
 
-//char meter[17];
 
+/*
 const PROGMEM uint8_t s_meter_bitmap[] = {
   B00000,B00000,B00000,B00000,B00000,B00100,B00100,B11011,
   B10000,B10000,B10000,B10000,B10100,B10100,B10100,B11011,
@@ -35,7 +35,18 @@ const PROGMEM uint8_t s_meter_bitmap[] = {
   B00010,B00010,B00010,B00010,B00110,B00110,B00110,B11011,
   B00001,B00001,B00001,B00001,B00101,B00101,B00101,B11011
 };
-PGM_P ps_meter_bitmap = reinterpret_cast<PGM_P>(s_meter_bitmap);
+*/
+
+const PROGMEM uint8_t meters_bitmap[] = {
+  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000 ,   //custom 1
+  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000 ,   //custom 2
+  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100 ,   //custom 3
+  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110 ,   //custom 4
+  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111 ,   //custom 5
+  B01000,  B11100,  B01000,  B00000,  B10111,  B10101,  B10101,  B10111     //custom 6
+};
+
+PGM_P p_metes_bitmap = reinterpret_cast<PGM_P>(meters_bitmap);
 
 const PROGMEM uint8_t lock_bitmap[8] = {
   0b01110,
@@ -60,38 +71,54 @@ void initMeter(){
   lcd.createChar(0, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i);
   lcd.createChar(1, tmpbytes);
 
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 8);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 8);
   lcd.createChar(2, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 16);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 16);
   lcd.createChar(3, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 24);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 24);
   lcd.createChar(4, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 28);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 32);
   lcd.createChar(5, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 32);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 40);
   lcd.createChar(6, tmpbytes);
 }
 
-/**
- * The meter is drawn with special characters.
- * character 1 is used to simple draw the blocks of the scale of the meter
- * characters 2 to 6 are used to draw the needle in positions 1 to within the block
- * This displays a meter from 0 to 100, -1 displays nothing
- */
+//by KD8CEC
+//0 ~ 25 : 30 over : + 10
+void drawMeter(int needle) {
+  //5Char + O over
+  int i;
 
- /*
+  for (i = 0; i < 5; i++) {
+    if (needle >= 5)
+      lcdMeter[i] = 5; //full
+    else if (needle > 0)
+      lcdMeter[i] = needle; //full
+    else  //0
+      lcdMeter[i] = 0x20;
+    
+    needle -= 5;
+  }
+
+  if (needle > 0)
+    lcdMeter[5] = 6;
+  else
+    lcdMeter[5] = 0x20;
+}
+
+/*
 void drawMeter(int8_t needle){
   int16_t best, i, s;
 
@@ -101,19 +128,18 @@ void drawMeter(int8_t needle){
   s = (needle * 4)/10;
   for (i = 0; i < 8; i++){
     if (s >= 5)
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     else if (s >= 0)
-      meter[i] = 2 + s;
+      lcdMeter[i] = 2 + s;
     else
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     s = s - 5;
   }
   if (needle >= 40)
-    meter[i-1] = 6;
-  meter[i] = 0;
+    lcdMeter[i-1] = 6;
+  lcdMeter[i] = 0;
 }
 */
-
 // The generic routine to display one line on the LCD 
 void printLine(unsigned char linenmbr, const char *c) {
   if ((displayOption1 & 0x01) == 0x01)
@@ -207,7 +233,6 @@ char byteToChar(byte srcByte){
 void updateDisplay() {
   // tks Jack Purdum W8TEE
   // replaced fsprint commmands by str commands for code size reduction
-  
   // replace code for Frequency numbering error (alignment, point...) by KD8CEC
   int i;
   unsigned long tmpFreq = frequency; //
@@ -234,10 +259,21 @@ void updateDisplay() {
     if (ritOn)
       strcpy(c, "RIT ");
     else {
-      if (isUSB)
-        strcpy(c, "USB ");
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          strcpy(c, "USB ");
+        else
+          strcpy(c, "LSB ");
+      }
+      else if (cwMode == 1)
+      {
+          strcpy(c, "CWL ");
+      }
       else
-        strcpy(c, "LSB ");
+      {
+          strcpy(c, "CWU ");
+      }
     }
     if (vfoActive == VFO_A) // VFO A is active
       strcat(c, "A:");