TX Check in auto keysend

ubitx_20/cat_libs.ino

@@ -130,10 +130,21 @@ void CatGetFreqMode(unsigned long freq, byte fromType)
   }
 
   //Mode Check
-  if (isUSB)
-    CAT_BUFF[4] = CAT_MODE_USB;
+  if (cwMode == 0)
+  {
+    if (isUSB)
+      CAT_BUFF[4] = CAT_MODE_USB;
+    else
+      CAT_BUFF[4] = CAT_MODE_LSB;
+  }
+  else if (cwMode == 1)
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
   else
-    CAT_BUFF[4] = CAT_MODE_LSB;
+  {
+      CAT_BUFF[4] = CAT_MODE_CW;
+  }
 
   SendCatData(5);
 }
@@ -198,12 +209,18 @@ void CatSetMode(byte tmpMode, byte fromType)
   
   if (!inTx)
   {
-    if (tmpMode == CAT_MODE_USB)
+    if (tmpMode == CAT_MODE_CW)
     {
+      cwMode = 1;
+    }
+    else if (tmpMode == CAT_MODE_USB)
+    {
+      cwMode = 0;
       isUSB = true;
     }
     else
     {
+      cwMode = 0;
       isUSB = false;
     }
 
@@ -358,10 +375,21 @@ void ReadEEPRom_FT817(byte fromType)
       CAT_BUFF[1] = 0xB2;
       break;      case 0x69 : //FM Mic (#29)  Contains 0-100 (decimal) as displayed
     case 0x78 :
-      if (isUSB)
-        CAT_BUFF[0] = CAT_MODE_USB;
-      else
-        CAT_BUFF[0] = CAT_MODE_LSB;
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          CAT_BUFF[0] = CAT_MODE_USB;
+        else
+          CAT_BUFF[0] = CAT_MODE_LSB;
+      }
+      else if (cwMode == 1)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
+      else if (cwMode == 2)
+      {
+          CAT_BUFF[0] = CAT_MODE_CW;
+      }
         
       if (CAT_BUFF[0] != 0) CAT_BUFF[0] = 1 << 5;
       break;
@@ -384,7 +412,7 @@ void ReadEEPRom_FT817(byte fromType)
       //7A  6 ? ?
       //7A  7 SPL On/Off  0 = Off, 1 = On
 
-      CAT_BUFF[0] = (isSplitOn ? 0xFF : 0x7F);
+      CAT_BUFF[0] = (splitOn ? 0xFF : 0x7F);
       break;
     case 0xB3 : //
       CAT_BUFF[0] = 0x00;

ubitx_20/cw_autokey.ino

@@ -365,6 +365,11 @@ void controlAutoCW(){
         //check interval time, if you want adjust interval between chars, modify below
         if (isAutoCWHold == 0 && (millis() - autoCWbeforeTime > cwSpeed * 3))
         {
+          if (!inTx){                                           //if not TX Status, change RX -> TX
+            keyDown = 0;
+            startTx(TX_CW, 0);  //disable updateDisplay Command for reduce latency time
+          }
+          
           sendCWChar(EEPROM.read(CW_AUTO_DATA + autoCWSendCharIndex++));
 
           if (autoCWSendCharIndex > autoCWSendCharEndIndex) {          //finish auto cw send

ubitx_20/ubitx_20.ino

@@ -151,6 +151,7 @@ int count = 0;          //to generally count ticks, loops, etc
 #define CW_SPEED 28
 
 //AT328 has 1KBytes EEPROM
+#define CW_CAL 252
 #define VFO_A_MODE 256
 #define VFO_B_MODE 257
 #define CW_DELAY 258
@@ -159,7 +160,8 @@ int count = 0;          //to generally count ticks, loops, etc
 #define TX_TUNE_TYPE 261  //
 #define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
 #define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)
+#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+  
 
 //for reduce cw key error, eeprom address
 #define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
@@ -232,7 +234,7 @@ int count = 0;          //to generally count ticks, loops, etc
 char ritOn = 0;
 char vfoActive = VFO_A;
 int8_t meter_reading = 0; // a -1 on meter makes it invisible
-unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier;
+unsigned long vfoA=7150000L, vfoB=14200000L, sideTone=800, usbCarrier, cwmCarrier;
 unsigned long vfoA_eeprom, vfoB_eeprom; //for protect eeprom life
 unsigned long frequency, ritRxFrequency, ritTxFrequency;  //frequency is the current frequency on the dial
 
@@ -249,7 +251,6 @@ byte saveIntervalSec = 10;  //second
 unsigned long saveCheckTime = 0;
 unsigned long saveCheckFreq = 0;
 
-bool isSplitOn = false;
 byte cwDelayTime = 60;
 byte delayBeforeCWStartTime = 50;
 
@@ -260,7 +261,7 @@ byte sideToneSub = 0;
 //DialLock
 byte isDialLock = 0;  //000000[0]vfoB [0]vfoA 0Bit : A, 1Bit : B
 byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
-byte arTuneStep[5];
+long arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
 byte displayOption1 = 0;
@@ -298,9 +299,13 @@ byte userCallsignLength = 0;    //7 : display callsign at system startup, 6~0 :
  */
 boolean txCAT = false;        //turned on if the transmitting due to a CAT command
 char inTx = 0;                //it is set to 1 if in transmit mode (whatever the reason : cw, ptt or cat)
-char splitOn = 0;             //working split, uses VFO B as the transmit frequency, (NOT IMPLEMENTED YET)
+char splitOn = 0;             //working split, uses VFO B as the transmit frequency
 char keyDown = 0;             //in cw mode, denotes the carrier is being transmitted
 char isUSB = 0;               //upper sideband was selected, this is reset to the default for the 
+
+char cwMode = 0;              //compatible original source, and extend mode //if cwMode == 0, mode check : isUSB, cwMode > 0, mode Check : cwMode
+                              //iscwMode = 0 : ssbmode, 1 :cwl, 2 : cwu, 3 : cwn (none tx)
+                              
                               //frequency when it crosses the frequency border of 10 MHz
 byte menuOn = 0;              //set to 1 when the menu is being displayed, if a menu item sets it to zero, the menu is exited
 unsigned long cwTimeout = 0;  //milliseconds to go before the cw transmit line is released and the radio goes back to rx mode
@@ -311,6 +316,10 @@ boolean modeCalibrate = false;//this mode of menus shows extended menus to calib
 
 unsigned long beforeIdle_ProcessTime = 0; //for check Idle time
 byte line2DisplayStatus = 0;  //0:Clear, 1 : menu, 1: DisplayFrom Idle, 
+char lcdMeter[17];
+
+byte isIFShift = 0;     //1 = ifShift, 2 extend
+long ifShiftValue = 0;  //
                               
 /**
  * Below are the basic functions that control the uBitx. Understanding the functions before 
@@ -364,22 +373,24 @@ void setNextHamBandFreq(unsigned long f, char moveDirection)
 
   EEPROM.get(HAM_BAND_FREQS + 4 * findedIndex, resultFreq);
   
-  loadMode = (byte)(resultFreq >> 30);
-  resultFreq = resultFreq & 0x3FFFFFFF;
+  //loadMode = (byte)(resultFreq >> 30);
+  //resultFreq = resultFreq & 0x3FFFFFFF;
+  loadMode = (byte)(resultFreq >> 29);
+  resultFreq = resultFreq & 0x1FFFFFFF;
   
   if ((resultFreq / 1000) < hamBandRange[(unsigned char)findedIndex][0] || (resultFreq / 1000) > hamBandRange[(unsigned char)findedIndex][1])
     resultFreq = (unsigned long)(hamBandRange[(unsigned char)findedIndex][0]) * 1000;
 
   setFrequency(resultFreq);
-  byteWithFreqToMode(loadMode);
+  byteToMode(loadMode, 1);
 }
 
 void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
   if (bandIndex >= 0)
-    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    //EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
+    EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x1FFFFFFF) | (mode << 29) );
 }
 
-
 /*
   KD8CEC
   When using the basic delay of the Arduino, the program freezes.
@@ -473,13 +484,27 @@ void setFrequency(unsigned long f){
   
   setTXFilters(f);
 
-  if (isUSB){
-    si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_USB);
+  if (cwMode == 0)
+  {
+    if (isUSB){
+      si5351bx_setfreq(2, SECOND_OSC_USB - usbCarrier + f  + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
+    else{
+      si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
   }
-  else{
-    si5351bx_setfreq(2, SECOND_OSC_LSB + usbCarrier + f);
-    si5351bx_setfreq(1, SECOND_OSC_LSB);
+  else
+  {
+    if (cwMode == 1){ //CWL
+      si5351bx_setfreq(2, SECOND_OSC_LSB + cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_LSB);
+    }
+    else{             //CWU
+      si5351bx_setfreq(2, SECOND_OSC_USB - cwmCarrier + f + (isIFShift ? ifShiftValue : 0));
+      si5351bx_setfreq(1, SECOND_OSC_USB);
+    }
   }
   
   frequency = f;
@@ -508,6 +533,21 @@ void startTx(byte txMode, byte isDisplayUpdate){
     ritRxFrequency = frequency;
     setFrequency(ritTxFrequency);
   }
+  else if (splitOn == 1) {
+      if (vfoActive == VFO_B) {
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+
+      setFrequency(frequency);
+  } //end of else
+  
 
   if (txMode == TX_CW){
     //turn off the second local oscillator and the bfo
@@ -517,10 +557,22 @@ void startTx(byte txMode, byte isDisplayUpdate){
     //shif the first oscillator to the tx frequency directly
     //the key up and key down will toggle the carrier unbalancing
     //the exact cw frequency is the tuned frequency + sidetone
-    if (isUSB)
-      si5351bx_setfreq(2, frequency + sideTone);
-    else
-      si5351bx_setfreq(2, frequency - sideTone); 
+
+    if (cwMode == 0)
+    {
+      if (isUSB)
+        si5351bx_setfreq(2, frequency + sideTone);
+      else
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else if (cwMode == 1) //CWL
+    {
+        si5351bx_setfreq(2, frequency - sideTone); 
+    }
+    else  //CWU
+    {
+        si5351bx_setfreq(2, frequency + sideTone);
+    }
   }
 
   //reduce latency time when begin of CW mode
@@ -532,10 +584,28 @@ void stopTx(){
   inTx = 0;
 
   digitalWrite(TX_RX, 0);           //turn off the tx
-  si5351bx_setfreq(0, usbCarrier);  //set back the carrier oscillator anyway, cw tx switches it off
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
+  else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));  //set back the carrier oscillator anyway, cw tx switches it off
 
   if (ritOn)
     setFrequency(ritRxFrequency);
+  else if (splitOn == 1) {
+      //vfo Change
+      if (vfoActive == VFO_B){
+        vfoActive = VFO_A;
+        frequency = vfoA;
+        byteToMode(vfoA_mode, 0);
+      }
+      else if (vfoActive == VFO_A){
+        vfoActive = VFO_B;
+        frequency = vfoB;
+        byteToMode(vfoB_mode, 0);
+      }
+      setFrequency(frequency);
+  } //end of else
   else
     setFrequency(frequency);
   
@@ -685,9 +755,8 @@ void doRIT(){
     updateDisplay();
   }
 }
-
-/**
- save Frequency and mode to eeprom
+/*
+ save Frequency and mode to eeprom for Auto Save with protected eeprom cycle, by kd8cec
  */
 void storeFrequencyAndMode(byte saveType)
 {
@@ -719,6 +788,22 @@ void storeFrequencyAndMode(byte saveType)
   }
 }
 
+//calculate step size from 1 byte, compatible uBITX Manager, by KD8CEC
+unsigned int byteToSteps(byte srcByte) {
+    byte powerVal = (byte)(srcByte >> 6);
+    unsigned int baseVal = srcByte & 0x3F;
+
+    if (powerVal == 1)
+        return baseVal * 10;
+    else if (powerVal == 2)
+        return baseVal * 100;
+    else if (powerVal == 3)
+        return baseVal * 1000;
+    else
+        return baseVal;
+}
+
+
 /**
  * The settings are read from EEPROM. The first time around, the values may not be 
  * present or out of range, in this case, some intelligent defaults are copied into the 
@@ -761,6 +846,7 @@ void initSettings(){
   if (EEPROM.read(VERSION_ADDRESS) != VERSION_NUM)
     EEPROM.write(VERSION_ADDRESS, VERSION_NUM);
 
+  EEPROM.get(CW_CAL, cwmCarrier);
 
   //for Save VFO_A_MODE to eeprom
   //0: default, 1:not use, 2:LSB, 3:USB, 4:CW, 5:AM, 6:FM
@@ -781,7 +867,7 @@ void initSettings(){
   else
   {
     Iambic_Key = true;
-    if (cwKeyType = 1)
+    if (cwKeyType == 1)
       keyerControl &= ~IAMBICB;
     else
       keyerControl |= IAMBICB;
@@ -824,7 +910,7 @@ void initSettings(){
     hamBandRange[0][0] = 1810; hamBandRange[0][1] = 2000; 
     hamBandRange[1][0] = 3500; hamBandRange[1][1] = 3800; 
     hamBandRange[2][0] = 5351; hamBandRange[2][1] = 5367; 
-    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7200; 
+    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;   //region 1
     hamBandRange[4][0] = 10100; hamBandRange[4][1] = 10150; 
     hamBandRange[5][0] = 14000; hamBandRange[5][1] = 14350; 
     hamBandRange[6][0] = 18068; hamBandRange[6][1] = 18168; 
@@ -838,8 +924,8 @@ void initSettings(){
   findedValidValueCount = 0;
   EEPROM.get(TUNING_STEP, tuneStepIndex);
   for (byte i = 0; i < 5; i++) {
-    arTuneStep[i] = EEPROM.read(TUNING_STEP + i + 1);
-    if (arTuneStep[i] >= 1 && arTuneStep[i] < 251) //Maximum 250 for check valid Value
+    arTuneStep[i] = byteToSteps(EEPROM.read(TUNING_STEP + i + 1));
+    if (arTuneStep[i] >= 1 && arTuneStep[i] <= 60000) //Maximum 650 for check valid Value
        findedValidValueCount++;
   }
 
@@ -909,15 +995,18 @@ void initSettings(){
   //original code with modified by kd8cec
   if (usbCarrier > 12010000l || usbCarrier < 11990000l)
     usbCarrier = 11995000l;
+
+  if (cwmCarrier > 12010000l || cwmCarrier < 11990000l)
+    cwmCarrier = 11995000l;
     
   if (vfoA > 35000000l || 3500000l > vfoA) {
      vfoA = 7150000l;
-     vfoA_mode = 2;
+     vfoA_mode = 2; //LSB
   }
   
   if (vfoB > 35000000l || 3500000l > vfoB) {
      vfoB = 14150000l;  
-     vfoB_mode = 3;
+     vfoB_mode = 3; //USB
   }
   //end of original code section
 
@@ -993,7 +1082,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.31")); 
+  printLineF(1, F("CECBT v0.35")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -1011,11 +1100,12 @@ void setup()
   }
   
   initPorts();     
+
+  byteToMode(vfoA_mode, 0);
   initOscillators();
 
   frequency = vfoA;
   saveCheckFreq = frequency;  //for auto save frequency
-  byteToMode(vfoA_mode);
   setFrequency(vfoA);
   updateDisplay();
 
@@ -1024,13 +1114,11 @@ void setup()
 }
 
 
-/**
- * The loop checks for keydown, ptt, function button and tuning.
- */
 //for debug
 int dbgCnt = 0;
 byte flasher = 0;
 
+//Auto save Frequency and Mode with Protected eeprom life by KD8CEC
 void checkAutoSaveFreqMode()
 {
   //when tx or ritOn, disable auto save
@@ -1079,10 +1167,12 @@ void loop(){
   if (!inTx){
     if (ritOn)
       doRIT();
+    //else if (isIFShift)
+    //  doIFShift();
     else 
       doTuningWithThresHold();
 
-    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 200) {
+    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 250) {
       idle_process();
       beforeIdle_ProcessTime = millis();
     }

ubitx_20/ubitx_factory_alignment.ino

@@ -37,6 +37,7 @@ void factory_alignment(){
 
   
   printLine2("#3:Test 3.5MHz");
+  cwMode = 0;
   isUSB = false;
   setFrequency(3500000l);
   updateDisplay();
@@ -59,6 +60,7 @@ void factory_alignment(){
   btnWaitForClick();
   printLine2("#5:Test 14MHz");
 
+  cwMode = 0;
   isUSB = true;
   setFrequency(14000000l);
   updateDisplay();
@@ -80,6 +82,7 @@ void factory_alignment(){
   printLine2("Alignment done");
   delay(1000);
 
+  cwMode = 0;
   isUSB = false;
   setFrequency(7150000l);
   updateDisplay();  

ubitx_20/ubitx_idle.ino

@@ -17,14 +17,241 @@
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 **************************************************************************/
+char line2Buffer[16];
+//KD8CEC 200Hz ST
+//L14.150 200Hz ST
+//U14.150 +150khz
+int freqScrollPosition = 0;
+//Example Line2 Optinal Display
+//immediate execution, not call by scheulder
+void updateLine2Buffer(char isDirectCall)
+{
+  unsigned long tmpFreq = 0;
+  if (isDirectCall == 0)
+  {
+    if (ritOn)
+    {
+      line2Buffer[0] = 'R';
+      line2Buffer[1] = 'i';
+      line2Buffer[2] = 't';
+      line2Buffer[3] = 'T';
+      line2Buffer[4] = 'X';
+      line2Buffer[5] = ':';
+  
+      //display frequency
+      tmpFreq = ritTxFrequency;
+      for (int i = 15; i >= 6; i--) {
+        if (tmpFreq > 0) {
+          if (i == 12 || i == 8) line2Buffer[i] = '.';
+          else {
+            line2Buffer[i] = tmpFreq % 10 + 0x30;
+            tmpFreq /= 10;
+          }
+        }
+        else
+          line2Buffer[i] = ' ';
+      }
+  
+      return;
+    } //end of ritOn display
 
+    //======================================================
+    //other VFO display
+    //======================================================
+    if (vfoActive == VFO_B)
+    {
+      tmpFreq = vfoA;
+      //line2Buffer[0] = 'A';
+    }
+    else 
+    {
+      tmpFreq = vfoB;
+      //line2Buffer[0] = 'B';
+    }
+  
+    // EXAMPLE 1 & 2
+    //U14.150.100
+    //display frequency
+    for (int i = 9; i >= 0; i--) {
+      if (tmpFreq > 0) {
+        if (i == 2 || i == 6) line2Buffer[i] = '.';
+        else {
+          line2Buffer[i] = tmpFreq % 10 + 0x30;
+          tmpFreq /= 10;
+        }
+      }
+      else
+        line2Buffer[i] = ' ';
+    }
+  
+    //EXAMPLE #1
+    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
+      line2Buffer[6] = 'k';
+    else
+    {
+      //example #2
+      if (freqScrollPosition++ > 18)    //none scroll display time
+      {
+        line2Buffer[6] = 'k';
+        if (freqScrollPosition > 25)
+          freqScrollPosition = -1;
+      }
+      else                              //scroll frequency 
+      {
+        line2Buffer[10] = 'H';
+        line2Buffer[11] = 'z';
+    
+        if (freqScrollPosition < 7)   
+        {
+          for (int i = 11; i >= 0; i--)
+            if (i - (7 - freqScrollPosition) >= 0)
+              line2Buffer[i] = line2Buffer[i - (7 - freqScrollPosition)];
+            else
+              line2Buffer[i] = ' ';
+        }
+        else
+        {
+          for (int i = 0; i < 11; i++)
+            if (i + (freqScrollPosition - 7) <= 11)
+              line2Buffer[i] = line2Buffer[i + (freqScrollPosition - 7)];
+            else
+              line2Buffer[i] = ' ';
+        }
+      }
+    } //scroll
+    
+    line2Buffer[7] = ' ';
+  } //check direct call by encoder
+  
+  if (isIFShift)
+  {
+    if (isDirectCall == 1)
+      for (int i = 0; i < 16; i++)
+        line2Buffer[i] = ' ';
+      
+      //IFShift Offset Value 
+    line2Buffer[8] = 'I';
+    line2Buffer[9] = 'F';
 
+    if (ifShiftValue == 0)
+    {
+      line2Buffer[10] = 'S';
+      line2Buffer[11] = ':';
+      line2Buffer[12] = 'O';
+      line2Buffer[13] = 'F';
+      line2Buffer[14] = 'F';
+    }
+    else
+    {
+      line2Buffer[10] = ifShiftValue >= 0 ? '+' : 0;
+      line2Buffer[11] = 0;
+      line2Buffer[12] = ' ';
+    
+      //11, 12, 13, 14, 15
+      memset(b, 0, sizeof(b));
+      ltoa(ifShiftValue, b, DEC);
+      strncat(line2Buffer, b, 5);
+    }
+    
+    if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
+        printLine2(line2Buffer);    
+  }       // end of display IF
+  else    // step display
+  {
+    if (isDirectCall != 0)
+      return;
+
+    memset(&line2Buffer[8], ' ', 8);
+    //Step
+    long tmpStep = arTuneStep[tuneStepIndex -1];
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
+      if (tmpStep > 0) {
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
+          tmpStep /= 10;
+      }
+      else
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+    //if (isStepKhz == 1)
+    //  line2Buffer[10] = 'k';
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[11] = 'H';
+      line2Buffer[12] = 'z';
+    }
+  
+    line2Buffer[13] = ' ';
+    //if (
+    //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
+    if (cwKeyType == 0)
+    {
+      line2Buffer[14] = 'S';
+      line2Buffer[15] = 'T';
+    }
+    else if (cwKeyType == 1)
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'A';
+    }
+    else
+    {
+      line2Buffer[14] = 'I';
+      line2Buffer[15] = 'B';
+    }    
+  }
+  
+}
+
+//meterType : 0 = S.Meter, 1 : P.Meter
+void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
+{
+  drawMeter(meterValue);  //call original source code
+  int lineNumber = 0;
+  if ((displayOption1 & 0x01) == 0x01)
+    lineNumber = 1;
+  
+  lcd.setCursor(drawPosition, lineNumber);
+
+  for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+    lcd.write(lcdMeter[i]);
+
+}
+
+byte testValue = 0;
+char checkCount = 0;
 void idle_process()
 {
   //space for user graphic display
   if (menuOn == 0)
   {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
     //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
+    if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
+      if (checkCount++ > 1)
+      {
+        updateLine2Buffer(0); //call by scheduler
+        printLine2(line2Buffer);
+        line2DisplayStatus = 2;
+        checkCount = 0;
+      }
+
+      //EX for Meters
+      /*
+      DisplayMeter(0, testValue++, 7);
+      if (testValue > 30)
+        testValue = 0;
+      */
+    }
   }
 }
 

ubitx_20/ubitx_si5351.ino

@@ -109,7 +109,11 @@ void initOscillators(){
   //initialize the SI5351
   si5351bx_init();
   si5351bx_vcoa = (SI5351BX_XTAL * SI5351BX_MSA) + calibration; // apply the calibration correction factor
-  si5351bx_setfreq(0, usbCarrier);
+
+  if (cwMode == 0)
+    si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));
+ else
+    si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));
 }
 
 

ubitx_20/ubitx_ui.ino

@@ -25,8 +25,8 @@ int btnDown(){
  * The current reading of the meter is assembled in the string called meter
  */
 
-//char meter[17];
 
+/*
 const PROGMEM uint8_t s_meter_bitmap[] = {
   B00000,B00000,B00000,B00000,B00000,B00100,B00100,B11011,
   B10000,B10000,B10000,B10000,B10100,B10100,B10100,B11011,
@@ -35,7 +35,18 @@ const PROGMEM uint8_t s_meter_bitmap[] = {
   B00010,B00010,B00010,B00010,B00110,B00110,B00110,B11011,
   B00001,B00001,B00001,B00001,B00101,B00101,B00101,B11011
 };
-PGM_P ps_meter_bitmap = reinterpret_cast<PGM_P>(s_meter_bitmap);
+*/
+
+const PROGMEM uint8_t meters_bitmap[] = {
+  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000,  B10000 ,   //custom 1
+  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000,  B11000 ,   //custom 2
+  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100,  B11100 ,   //custom 3
+  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110,  B11110 ,   //custom 4
+  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111,  B11111 ,   //custom 5
+  B01000,  B11100,  B01000,  B00000,  B10111,  B10101,  B10101,  B10111     //custom 6
+};
+
+PGM_P p_metes_bitmap = reinterpret_cast<PGM_P>(meters_bitmap);
 
 const PROGMEM uint8_t lock_bitmap[8] = {
   0b01110,
@@ -60,38 +71,56 @@ void initMeter(){
   lcd.createChar(0, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i);
   lcd.createChar(1, tmpbytes);
 
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 8);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 8);
   lcd.createChar(2, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 16);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 16);
   lcd.createChar(3, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 24);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 24);
   lcd.createChar(4, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 28);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 32);
   lcd.createChar(5, tmpbytes);
   
   for (i = 0; i < 8; i++)
-    tmpbytes[i] = pgm_read_byte(ps_meter_bitmap + i + 32);
+    tmpbytes[i] = pgm_read_byte(p_metes_bitmap + i + 40);
   lcd.createChar(6, tmpbytes);
 }
 
-/**
- * The meter is drawn with special characters.
- * character 1 is used to simple draw the blocks of the scale of the meter
- * characters 2 to 6 are used to draw the needle in positions 1 to within the block
- * This displays a meter from 0 to 100, -1 displays nothing
- */
+//by KD8CEC
+//0 ~ 25 : 30 over : + 10
+void drawMeter(int needle) {
+  //5Char + O over
+  int drawCharLength = needle / 5;
+  int drawCharLengthLast = needle % 5;
+  int i;
 
- /*
+  for (i = 0; i < 5; i++) {
+    if (needle >= 5)
+      lcdMeter[i] = 5; //full
+    else if (needle > 0)
+      lcdMeter[i] = needle; //full
+    else  //0
+      lcdMeter[i] = 0x20;
+    
+    needle -= 5;
+  }
+
+  if (needle > 0)
+    lcdMeter[5] = 6;
+  else
+    lcdMeter[5] = 0x20;
+}
+
+/*
 void drawMeter(int8_t needle){
   int16_t best, i, s;
 
@@ -101,19 +130,18 @@ void drawMeter(int8_t needle){
   s = (needle * 4)/10;
   for (i = 0; i < 8; i++){
     if (s >= 5)
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     else if (s >= 0)
-      meter[i] = 2 + s;
+      lcdMeter[i] = 2 + s;
     else
-      meter[i] = 1;
+      lcdMeter[i] = 1;
     s = s - 5;
   }
   if (needle >= 40)
-    meter[i-1] = 6;
-  meter[i] = 0;
+    lcdMeter[i-1] = 6;
+  lcdMeter[i] = 0;
 }
 */
-
 // The generic routine to display one line on the LCD 
 void printLine(unsigned char linenmbr, const char *c) {
   if ((displayOption1 & 0x01) == 0x01)
@@ -207,7 +235,6 @@ char byteToChar(byte srcByte){
 void updateDisplay() {
   // tks Jack Purdum W8TEE
   // replaced fsprint commmands by str commands for code size reduction
-  
   // replace code for Frequency numbering error (alignment, point...) by KD8CEC
   int i;
   unsigned long tmpFreq = frequency; //
@@ -234,10 +261,21 @@ void updateDisplay() {
     if (ritOn)
       strcpy(c, "RIT ");
     else {
-      if (isUSB)
-        strcpy(c, "USB ");
+      if (cwMode == 0)
+      {
+        if (isUSB)
+          strcpy(c, "USB ");
+        else
+          strcpy(c, "LSB ");
+      }
+      else if (cwMode == 1)
+      {
+          strcpy(c, "CWL ");
+      }
       else
-        strcpy(c, "LSB ");
+      {
+          strcpy(c, "CWU ");
+      }
     }
     if (vfoActive == VFO_A) // VFO A is active
       strcat(c, "A:");