ubitx-v5d/ubitx_20/ubitx_keyer.ino
2018-01-10 11:34:15 +09:00

187 lines
5.8 KiB
C++

/**
* CW Keyer
*
* The CW keyer handles either a straight key or an iambic / paddle key.
* They all use just one analog input line. This is how it works.
* The analog line has the internal pull-up resistor enabled.
* When a straight key is connected, it shorts the pull-up resistor, analog input is 0 volts
* When a paddle is connected, the dot and the dash are connected to the analog pin through
* a 10K and a 2.2K resistors. These produce a 4v and a 2v input to the analog pins.
* So, the readings are as follows :
* 0v - straight key
* 1-2.5 v - paddle dot
* 2.5 to 4.5 v - paddle dash
* 2.0 to 0.5 v - dot and dash pressed
*
* The keyer is written to transparently handle all these cases
*
* Generating CW
* The CW is cleanly generated by unbalancing the front-end mixer
* and putting the local oscillator directly at the CW transmit frequency.
* The sidetone, generated by the Arduino is injected into the volume control
*/
// in milliseconds, this is the parameter that determines how long the tx will hold between cw key downs
//#define CW_TIMEOUT (600l) //Change to CW Delaytime for value save to eeprom
#define PADDLE_DOT 1
#define PADDLE_DASH 2
#define PADDLE_BOTH 3
#define PADDLE_STRAIGHT 4
//we store the last padde's character
//to alternatively send dots and dashes
//when both are simultaneously pressed
char lastPaddle = 0;
//reads the analog keyer pin and reports the paddle
byte getPaddle(){
int paddle = analogRead(ANALOG_KEYER);
if (paddle > 800) // above 4v is up
return 0;
if (paddle > 600) // 4-3v is dot
return PADDLE_DASH;
else if (paddle > 300) //1-2v is dash
return PADDLE_DOT;
else if (paddle > 50)
return PADDLE_BOTH; //both are between 1 and 2v
else
return PADDLE_STRAIGHT; //less than 1v is the straight key
}
/**
* Starts transmitting the carrier with the sidetone
* It assumes that we have called cwTxStart and not called cwTxStop
* each time it is called, the cwTimeOut is pushed further into the future
*/
void cwKeydown(){
keyDown = 1; //tracks the CW_KEY
tone(CW_TONE, (int)sideTone);
digitalWrite(CW_KEY, 1);
//Modified by KD8CEC, for CW Delay Time save to eeprom
//cwTimeout = millis() + CW_TIMEOUT;
cwTimeout = millis() + cwDelayTime * 10;
}
/**
* Stops the cw carrier transmission along with the sidetone
* Pushes the cwTimeout further into the future
*/
void cwKeyUp(){
keyDown = 0; //tracks the CW_KEY
noTone(CW_TONE);
digitalWrite(CW_KEY, 0);
//Modified by KD8CEC, for CW Delay Time save to eeprom
//cwTimeout = millis() + CW_TIMEOUT;
cwTimeout = millis() + cwDelayTime * 10;
}
/**
* The keyer handles the straight key as well as the iambic key
* This module keeps looping until the user stops sending cw
* if the cwTimeout is set to 0, then it means, we have to exit the keyer loop
* Each time the key is hit the cwTimeout is pushed to a time in the future by cwKeyDown()
*/
void cwKeyer(){
byte paddle;
lastPaddle = 0;
while(1){
paddle = getPaddle();
// do nothing if the paddle has not been touched, unless
// we are in the cw mode and we have timed out
if (!paddle){
//modifed by KD8CEC for auto CW Send
if (isCWAutoMode > 1) //if while auto cw sending, dont stop tx by paddle position
return;
if (0 < cwTimeout && cwTimeout < millis()){
cwTimeout = 0;
keyDown = 0;
stopTx();
}
if (!cwTimeout)
return;
//if a paddle was used (not a straight key) we should extend the space to be a full dash
//by adding two more dots long space (one has already been added at the end of the dot or dash)
/*
if (cwTimeout > 0 && lastPaddle != PADDLE_STRAIGHT)
delay_background(cwSpeed * 2, 3);
//delay(cwSpeed * 2);
// got back to the begining of the loop, if no further activity happens on the paddle or the straight key
// we will time out, and return out of this routine
delay(5);
*/
continue;
}
//if while auto cw send, stop auto cw
//but isAutoCWHold for Manual Keying with cwAutoSend
if (isCWAutoMode > 1 && isAutoCWHold == 0)
isCWAutoMode = 1; //read status
//Remoark Debug code / Serial Use by CAT Protocol
//Serial.print("paddle:");Serial.println(paddle);
// if we are here, it is only because the key or the paddle is pressed
if (!inTx){
keyDown = 0;
//Modified by KD8CEC, for CW Delay Time save to eeprom
//cwTimeout = millis() + CW_TIMEOUT;
cwTimeout = millis() + cwDelayTime * 10;
startTx(TX_CW, 0); //disable updateDisplay Command for reduce latency time
updateDisplay();
//DelayTime Option
delay_background(delayBeforeCWStartTime * 2, 2);
}
// star the transmission)
// we store the transmitted character in the lastPaddle
cwKeydown();
if (paddle == PADDLE_DOT){
//delay(cwSpeed);
delay_background(cwSpeed, 3);
lastPaddle = PADDLE_DOT;
}
else if (paddle == PADDLE_DASH){
//delay(cwSpeed * 3);
delay_background(cwSpeed * 3, 3);
lastPaddle = PADDLE_DASH;
}
else if (paddle == PADDLE_BOTH){ //both paddles down
//depending upon what was sent last, send the other
if (lastPaddle == PADDLE_DOT) {
//delay(cwSpeed * 3);
delay_background(cwSpeed * 3, 3);
lastPaddle = PADDLE_DASH;
}else{
//delay(cwSpeed);
delay_background(cwSpeed, 3);
lastPaddle = PADDLE_DOT;
}
}
else if (paddle == PADDLE_STRAIGHT){
while (getPaddle() == PADDLE_STRAIGHT) {
delay(1);
Check_Cat(2);
}
lastPaddle = PADDLE_STRAIGHT;
}
cwKeyUp();
//introduce a dot long gap between characters if the keyer was used
if (lastPaddle != PADDLE_STRAIGHT)
delay(cwSpeed);
}
}