Change RIT tune step (freq tune step)

ubitx_20/cat_libs.ino

@@ -109,7 +109,8 @@ void CatSetFreq(byte fromType)
 //#define BCD_LEN 9
 //PROTOCOL : 0x03
 //Computer <-(frequency)-> TRCV CAT_BUFF
-void CatGetFreqMode(unsigned long freq, byte fromType)
+//void CatGetFreqMode(unsigned long freq, byte fromType)
+void CatGetFreqMode(unsigned long freq) //for remove warning messages
 {
   int i;
   byte tmpValue;
@@ -149,15 +150,21 @@ void CatGetFreqMode(unsigned long freq, byte fromType)
   SendCatData(5);
 }
 
-void CatSetSplit(boolean isSplit, byte fromType)
+//void CatSetSplit(boolean isSplit, byte fromType)
+void CatSetSplit(boolean isSplit) //for remove warning messages
 {
+  if (isSplit)
+    splitOn = 1;
+  else
+    splitOn = 0;
     
   Serial.write(ACK);
 }
 
 void CatSetPTT(boolean isPTTOn, byte fromType)
 {
-  if (fromType == 2 || fromType == 3) {
+  //
+  if ((!inTx) && (fromType == 2 || fromType == 3)) {
     Serial.write(ACK);  
     return;  
   }
@@ -193,7 +200,7 @@ void CatSetPTT(boolean isPTTOn, byte fromType)
 void CatVFOToggle(boolean isSendACK, byte fromType)
 {
   if (fromType != 2 && fromType != 3) {
-    menuVfoToggle(1, 0);
+    menuVfoToggle(1);
   }  
 
   if (isSendACK)
@@ -232,7 +239,8 @@ void CatSetMode(byte tmpMode, byte fromType)
 }
 
 //Read EEProm by uBITX Manager Software
-void ReadEEPRom(byte fromType)
+//void ReadEEPRom(byte fromType)
+void ReadEEPRom() //for remove warnings.
 {
   //5BYTES
   //CAT_BUFF[0] [1] [2] [3] [4] //4 COMMAND
@@ -255,7 +263,8 @@ void ReadEEPRom(byte fromType)
 }
 
 //Write just proecess 1byes
-void WriteEEPRom(byte fromType)
+//void WriteEEPRom(byte fromType)
+void WriteEEPRom(void)  //for remove warning
 {
   //5BYTES
   uint16_t eepromStartIndex = CAT_BUFF[0] + CAT_BUFF[1] * 256;
@@ -275,7 +284,8 @@ void WriteEEPRom(byte fromType)
   }
 }
 
-void ReadEEPRom_FT817(byte fromType)
+//void ReadEEPRom_FT817(byte fromType)
+void ReadEEPRom_FT817(void) //for remove warnings
 {
   byte temp0 = CAT_BUFF[0];
   byte temp1 = CAT_BUFF[1];
@@ -601,7 +611,8 @@ void WriteEEPRom_FT817(byte fromType)
   Serial.write(ACK);
 }
 
-void CatRxStatus(byte fromType) 
+//void CatRxStatus(byte fromType) 
+void CatRxStatus(void)  //for remove warning
 {
   byte sMeterValue = 1;
 
@@ -621,7 +632,8 @@ void CatRxStatus(byte fromType)
 }
 
 
-void CatTxStatus(byte fromType)
+//void CatTxStatus(byte fromType)
+void CatTxStatus(void)  //for remove warning
 {
   boolean isHighSWR = false;
   boolean isSplitOn = false;
@@ -722,11 +734,11 @@ void Check_Cat(byte fromType)
       
     case 0x02 : //Split On
     case 0x82:  //Split Off
-      CatSetSplit(CAT_BUFF[4] == 0x02, fromType);
+      CatSetSplit(CAT_BUFF[4] == 0x02);
       break;
 
     case 0x03 :   //Read Frequency and mode
-      CatGetFreqMode(frequency, fromType);
+      CatGetFreqMode(frequency);
       break;
 
     case 0x07 :   //Set Operating  Mode
@@ -743,24 +755,24 @@ void Check_Cat(byte fromType)
       break;
 
     case 0xDB:  //Read uBITX EEPROM Data
-      ReadEEPRom(fromType); //Call by uBITX Manager Program
+      ReadEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBB:  //Read FT-817 EEPROM Data  (for comfirtable)
-      ReadEEPRom_FT817(fromType);
+      ReadEEPRom_FT817();
       break;
 
     case 0xDC:  //Write uBITX EEPROM Data
-      WriteEEPRom(fromType); //Call by uBITX Manager Program
+      WriteEEPRom(); //Call by uBITX Manager Program
       break;
     case 0xBC:  //Write FT-817 EEPROM Data  (for comfirtable)
       WriteEEPRom_FT817(fromType);
       break;
 
     case 0xE7 :       //Read RX Status
-      CatRxStatus(fromType);
+      CatRxStatus();
       break;
     case 0xF7:      //Read TX Status
-      CatTxStatus(fromType);
+      CatTxStatus();
       break;
     default:
     /*

ubitx_20/cw_autokey.ino

@@ -365,6 +365,11 @@ void controlAutoCW(){
         //check interval time, if you want adjust interval between chars, modify below
         if (isAutoCWHold == 0 && (millis() - autoCWbeforeTime > cwSpeed * 3))
         {
+          if (!inTx){                                           //if not TX Status, change RX -> TX
+            keyDown = 0;
+            startTx(TX_CW, 0);  //disable updateDisplay Command for reduce latency time
+          }
+          
           sendCWChar(EEPROM.read(CW_AUTO_DATA + autoCWSendCharIndex++));
 
           if (autoCWSendCharIndex > autoCWSendCharEndIndex) {          //finish auto cw send

ubitx_20/ubitx_20.ino

@@ -156,11 +156,12 @@ int count = 0;          //to generally count ticks, loops, etc
 #define VFO_B_MODE 257
 #define CW_DELAY 258
 #define CW_START 259
-#define HAM_BAND_COUNT 260  //
+#define HAM_BAND_COUNT 260    //
-#define TX_TUNE_TYPE 261  //
+#define TX_TUNE_TYPE 261      //
-#define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
+#define HAM_BAND_RANGE 262    //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
-#define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
+#define HAM_BAND_FREQS 302    //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)
+#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)  //1STEP : 
+  
 
 //for reduce cw key error, eeprom address
 #define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
@@ -179,6 +180,10 @@ int count = 0;          //to generally count ticks, loops, etc
 #define DISPLAY_OPTION1  361   //Display Option1
 #define DISPLAY_OPTION2  362   //Display Option2
 
+#define CHANNEL_FREQ    630   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define CHANNEL_DESC    710   //Channel 1 ~ 20, 1 Channel = 4 bytes
+#define RESERVE3        770   //Reserve3 between Channel and Firmware id check
+
 //Check Firmware type and version
 #define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
 #define VERSION_ADDRESS 779   //check Firmware version
@@ -260,7 +265,7 @@ byte sideToneSub = 0;
 //DialLock
 byte isDialLock = 0;  //000000[0]vfoB [0]vfoA 0Bit : A, 1Bit : B
 byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
-byte arTuneStep[5];
+long arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
 byte displayOption1 = 0;
@@ -381,7 +386,7 @@ void setNextHamBandFreq(unsigned long f, char moveDirection)
     resultFreq = (unsigned long)(hamBandRange[(unsigned char)findedIndex][0]) * 1000;
 
   setFrequency(resultFreq);
-  byteWithFreqToMode(loadMode);
+  byteToMode(loadMode, 1);
 }
 
 void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
@@ -536,12 +541,12 @@ void startTx(byte txMode, byte isDisplayUpdate){
       if (vfoActive == VFO_B) {
         vfoActive = VFO_A;
         frequency = vfoA;
-        byteToMode(vfoA_mode);
+        byteToMode(vfoA_mode, 0);
       }
       else if (vfoActive == VFO_A){
         vfoActive = VFO_B;
         frequency = vfoB;
-        byteToMode(vfoB_mode);
+        byteToMode(vfoB_mode, 0);
       }
 
       setFrequency(frequency);
@@ -596,12 +601,12 @@ void stopTx(){
       if (vfoActive == VFO_B){
         vfoActive = VFO_A;
         frequency = vfoA;
-        byteToMode(vfoA_mode);
+        byteToMode(vfoA_mode, 0);
       }
       else if (vfoActive == VFO_A){
         vfoActive = VFO_B;
         frequency = vfoB;
-        byteToMode(vfoB_mode);
+        byteToMode(vfoB_mode, 0);
       }
       setFrequency(frequency);
   } //end of else
@@ -691,7 +696,6 @@ byte lastMovedirection = 0; //0 : stop, 1 : cw, 2 : ccw
 void doTuningWithThresHold(){
   int s = 0;
   unsigned long prev_freq;
-  long incdecValue = 0;
 
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02)))
@@ -745,36 +749,19 @@ void doRIT(){
   unsigned long old_freq = frequency;
 
   if (knob < 0)
-    frequency -= 100l;
+    frequency -= (arTuneStep[tuneStepIndex -1]);  //
+    //frequency -= 100l;
   else if (knob > 0)
-    frequency += 100;
+    frequency += (arTuneStep[tuneStepIndex -1]);  //
+    //frequency += 100;
  
   if (old_freq != frequency){
     setFrequency(frequency);
     updateDisplay();
   }
 }
-
 /*
-void doIFShift(){
+ save Frequency and mode to eeprom for Auto Save with protected eeprom cycle, by kd8cec
-  int knob = enc_read();
-  unsigned long old_freq = frequency;
-
-  if (knob != 0)
-  {
-    if (knob < 0)
-      ifShiftValue -= 1l;
-    else if (knob > 0)
-      ifShiftValue += 1;
-
-    updateLine2Buffer(1);
-    setFrequency(frequency);
-  }
-}
-*/
-
-/**
- save Frequency and mode to eeprom
  */
 void storeFrequencyAndMode(byte saveType)
 {
@@ -806,6 +793,22 @@ void storeFrequencyAndMode(byte saveType)
   }
 }
 
+//calculate step size from 1 byte, compatible uBITX Manager, by KD8CEC
+unsigned int byteToSteps(byte srcByte) {
+    byte powerVal = (byte)(srcByte >> 6);
+    unsigned int baseVal = srcByte & 0x3F;
+
+    if (powerVal == 1)
+        return baseVal * 10;
+    else if (powerVal == 2)
+        return baseVal * 100;
+    else if (powerVal == 3)
+        return baseVal * 1000;
+    else
+        return baseVal;
+}
+
+
 /**
  * The settings are read from EEPROM. The first time around, the values may not be 
  * present or out of range, in this case, some intelligent defaults are copied into the 
@@ -906,13 +909,13 @@ void initSettings(){
   if ((3 < tuneTXType && tuneTXType < 100) || 103 < tuneTXType || useHamBandCount < 1 || findedValidValueCount < 5)
   {
     tuneTXType = 2;
-    //if empty band Information, auto insert default region 1 frequency range
+    //if empty band Information, auto insert default region 2 frequency range
     //This part is made temporary for people who have difficulty setting up, so can remove it when you run out of memory.
     useHamBandCount = 10;
     hamBandRange[0][0] = 1810; hamBandRange[0][1] = 2000; 
     hamBandRange[1][0] = 3500; hamBandRange[1][1] = 3800; 
     hamBandRange[2][0] = 5351; hamBandRange[2][1] = 5367; 
-    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;   //region 1
+    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;     //region 2
     hamBandRange[4][0] = 10100; hamBandRange[4][1] = 10150; 
     hamBandRange[5][0] = 14000; hamBandRange[5][1] = 14350; 
     hamBandRange[6][0] = 18068; hamBandRange[6][1] = 18168; 
@@ -926,8 +929,8 @@ void initSettings(){
   findedValidValueCount = 0;
   EEPROM.get(TUNING_STEP, tuneStepIndex);
   for (byte i = 0; i < 5; i++) {
-    arTuneStep[i] = EEPROM.read(TUNING_STEP + i + 1);
+    arTuneStep[i] = byteToSteps(EEPROM.read(TUNING_STEP + i + 1));
-    if (arTuneStep[i] >= 1 && arTuneStep[i] < 251) //Maximum 250 for check valid Value
+    if (arTuneStep[i] >= 1 && arTuneStep[i] <= 60000) //Maximum 650 for check valid Value
        findedValidValueCount++;
   }
 
@@ -1003,12 +1006,12 @@ void initSettings(){
     
   if (vfoA > 35000000l || 3500000l > vfoA) {
      vfoA = 7150000l;
-     vfoA_mode = 2;
+     vfoA_mode = 2; //LSB
   }
   
   if (vfoB > 35000000l || 3500000l > vfoB) {
      vfoB = 14150000l;  
-     vfoB_mode = 3;
+     vfoB_mode = 3; //USB
   }
   //end of original code section
 
@@ -1084,7 +1087,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.33")); 
+  printLineF(1, F("CECBT v1.01")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -1103,7 +1106,7 @@ void setup()
   
   initPorts();     
 
-  byteToMode(vfoA_mode);
+  byteToMode(vfoA_mode, 0);
   initOscillators();
 
   frequency = vfoA;
@@ -1115,14 +1118,7 @@ void setup()
     factory_alignment();
 }
 
-
+//Auto save Frequency and Mode with Protected eeprom life by KD8CEC
-/**
- * The loop checks for keydown, ptt, function button and tuning.
- */
-//for debug
-int dbgCnt = 0;
-byte flasher = 0;
-
 void checkAutoSaveFreqMode()
 {
   //when tx or ritOn, disable auto save
@@ -1140,18 +1136,8 @@ void checkAutoSaveFreqMode()
     //check time for Frequency auto save
     if (millis() - saveCheckTime > saveIntervalSec * 1000)
     {
-      if (vfoActive == VFO_A)
+      FrequencyToVFO(1);
-      {
+      saveCheckTime = 0;  //for reduce cpu use rate
-        vfoA = frequency;
-        vfoA_mode = modeToByte();
-        storeFrequencyAndMode(1);
-      }
-      else
-      {
-        vfoB = frequency;
-        vfoB_mode = modeToByte();
-        storeFrequencyAndMode(2);
-      }
     }
   }
 }
@@ -1178,11 +1164,11 @@ void loop(){
 
     if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 250) {
       idle_process();
+      checkAutoSaveFreqMode();  //move here form out scope for reduce cpu use rate
       beforeIdle_ProcessTime = millis();
     }
   } //end of check TX Status
 
   //we check CAT after the encoder as it might put the radio into TX
   Check_Cat(inTx? 1 : 0);
-  checkAutoSaveFreqMode();
 }

ubitx_20/ubitx_idle.ino

@@ -17,7 +17,7 @@
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 **************************************************************************/
-byte line2Buffer[16];
+char line2Buffer[16];
 //KD8CEC 200Hz ST
 //L14.150 200Hz ST
 //U14.150 +150khz
@@ -53,8 +53,11 @@ void updateLine2Buffer(char isDirectCall)
       }
   
       return;
-    }
+    } //end of ritOn display
 
+    //======================================================
+    //other VFO display
+    //======================================================
     if (vfoActive == VFO_B)
     {
       tmpFreq = vfoA;
@@ -82,18 +85,18 @@ void updateLine2Buffer(char isDirectCall)
     }
   
     //EXAMPLE #1
-    if ((displayOption1 & 0x04) == 0x00)
+    if ((displayOption1 & 0x04) == 0x00)  //none scroll display
       line2Buffer[6] = 'k';
     else
     {
       //example #2
-      if (freqScrollPosition++ > 18)
+      if (freqScrollPosition++ > 18)    //none scroll display time
       {
         line2Buffer[6] = 'k';
         if (freqScrollPosition > 25)
           freqScrollPosition = -1;
       }
-      else
+      else                              //scroll frequency 
       {
         line2Buffer[10] = 'H';
         line2Buffer[11] = 'z';
@@ -115,11 +118,11 @@ void updateLine2Buffer(char isDirectCall)
               line2Buffer[i] = ' ';
         }
       }
-    }
+    } //scroll
+    
     line2Buffer[7] = ' ';
   } //check direct call by encoder
   
-  
   if (isIFShift)
   {
     if (isDirectCall == 1)
@@ -152,24 +155,38 @@ void updateLine2Buffer(char isDirectCall)
     
     if (isDirectCall == 1)  //if call by encoder (not scheduler), immediate print value
         printLine2(line2Buffer);    
-  }
+  }       // end of display IF
-  else
+  else    // step display
   {
     if (isDirectCall != 0)
       return;
 
+    memset(&line2Buffer[8], ' ', 8);
     //Step
-    byte tmpStep = arTuneStep[tuneStepIndex -1];
+    long tmpStep = arTuneStep[tuneStepIndex -1];
-    for (int i = 10; i >= 8; i--) {
+    
+    byte isStepKhz = 0;
+    if (tmpStep >= 1000)
+    {
+      isStepKhz = 2;
+    }
+      
+    for (int i = 10; i >= 8 - isStepKhz; i--) {
       if (tmpStep > 0) {
-          line2Buffer[i] = tmpStep % 10 + 0x30;
+          line2Buffer[i + isStepKhz] = tmpStep % 10 + 0x30;
           tmpStep /= 10;
       }
       else
-        line2Buffer[i] = ' ';
+        line2Buffer[i +isStepKhz] = ' ';
+    }
+    //if (isStepKhz == 1)
+    //  line2Buffer[10] = 'k';
+
+    if (isStepKhz == 0)
+    {
+      line2Buffer[11] = 'H';
+      line2Buffer[12] = 'z';
     }
-    line2Buffer[11] = 'H';
-    line2Buffer[12] = 'z';
   
     line2Buffer[13] = ' ';
     //if (
@@ -196,16 +213,18 @@ void updateLine2Buffer(char isDirectCall)
 //meterType : 0 = S.Meter, 1 : P.Meter
 void DisplayMeter(byte meterType, byte meterValue, char drawPosition)
 {
-  drawMeter(meterValue);  //call original source code
+  if (meterType == 0 || meterType == 1 || meterType == 2)
-  int lineNumber = 0;
+  {
-  if ((displayOption1 & 0x01) == 0x01)
+    drawMeter(meterValue);  //call original source code
-    lineNumber = 1;
+    int lineNumber = 0;
+    if ((displayOption1 & 0x01) == 0x01)
+      lineNumber = 1;
     
-  lcd.setCursor(drawPosition, lineNumber);
+    lcd.setCursor(drawPosition, lineNumber);
-
-  for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
-    lcd.write(lcdMeter[i]);
   
+    for (int i = 0; i < 6; i++) //meter 5 + +db 1 = 6
+      lcd.write(lcdMeter[i]);
+  }
 }
 
 byte testValue = 0;
@@ -215,6 +234,9 @@ void idle_process()
   //space for user graphic display
   if (menuOn == 0)
   {
+    if ((displayOption1 & 0x10) == 0x10)    //always empty topline
+      return;
+      
     //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
     if (line2DisplayStatus == 0 || (((displayOption1 & 0x04) == 0x04) && line2DisplayStatus == 2)) {
       if (checkCount++ > 1)

ubitx_20/ubitx_keyer.ino

@@ -90,13 +90,13 @@ void cwKeyUp(){
 #define PDLSWAP 0x08 // 0 for normal, 1 for swap
 #define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
 enum KSTYPE {IDLE, CHK_DIT, CHK_DAH, KEYED_PREP, KEYED, INTER_ELEMENT };
-static long ktimer;
+static unsigned long ktimer;
 unsigned char keyerState = IDLE;
 
 //Below is a test to reduce the keying error. do not delete lines
 //create by KD8CEC for compatible with new CW Logic
 char update_PaddleLatch(byte isUpdateKeyState) {
-  unsigned char tmpKeyerControl;
+  unsigned char tmpKeyerControl = 0;
   int paddle = analogRead(ANALOG_KEYER);
 
   if (paddle >= cwAdcDashFrom && paddle <= cwAdcDashTo)
@@ -126,9 +126,7 @@ char update_PaddleLatch(byte isUpdateKeyState) {
 // modified by KD8CEC
 ******************************************************************************/
 void cwKeyer(void){
-  byte paddle;
   lastPaddle = 0;
-  int dot,dash;
   bool continue_loop = true;
   unsigned tmpKeyControl = 0;
   
@@ -174,6 +172,9 @@ void cwKeyer(void){
           keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
           keyerState = KEYED; // next state
           if (!inTx){
+            //DelayTime Option
+            delay_background(delayBeforeCWStartTime * 2, 2);
+            
             keyDown = 0;
             cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
             startTx(TX_CW, 1);
@@ -206,7 +207,7 @@ void cwKeyer(void){
           break;
       }
   
-      Check_Cat(3);
+      Check_Cat(2);
     } //end of while
   }
   else{
@@ -214,6 +215,9 @@ void cwKeyer(void){
       if (update_PaddleLatch(0) == DIT_L) {
         // if we are here, it is only because the key is pressed
         if (!inTx){
+          //DelayTime Option
+          delay_background(delayBeforeCWStartTime * 2, 2);
+          
           keyDown = 0;
           cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT; 
           startTx(TX_CW, 1);
@@ -231,13 +235,14 @@ void cwKeyer(void){
           keyDown = 0;
           stopTx();
         }
-        if (!cwTimeout)
+        //if (!cwTimeout) //removed by KD8CEC
-          return;
+        //   return;
         // got back to the beginning of the loop, if no further activity happens on straight key
         // we will time out, and return out of this routine 
         //delay(5);
-        delay_background(5, 3);
+        //delay_background(5, 3); //removed by KD8CEC
-        continue;
+        //continue;               //removed by KD8CEC
+        return;                   //Tx stop control by Main Loop
       }
 
       Check_Cat(2);

ubitx_20/ubitx_ui.ino

@@ -99,8 +99,6 @@ void initMeter(){
 //0 ~ 25 : 30 over : + 10
 void drawMeter(int needle) {
   //5Char + O over
-  int drawCharLength = needle / 5;
-  int drawCharLengthLast = needle % 5;
   int i;
 
   for (i = 0; i < 5; i++) {
@@ -235,7 +233,6 @@ char byteToChar(byte srcByte){
 void updateDisplay() {
   // tks Jack Purdum W8TEE
   // replaced fsprint commmands by str commands for code size reduction
-  
   // replace code for Frequency numbering error (alignment, point...) by KD8CEC
   int i;
   unsigned long tmpFreq = frequency; //