ubitx-v5x/ubitx_20/ubitx_si5351.ino
2018-03-19 21:35:41 +09:00

173 lines
7.0 KiB
C++

/************************************************************************************
* KD8CEC
* kd8cec@gmail.com http://www.hamskey.com
*
* Merge two SI5351 Librarys
* KE7ER's fixed vco and variable Clocks Configure values
* G3ZIL's fixed Clock Configure Value and variable VCO
* * I have combined the two libraries above. All licenses follow the above library.
*
* PLL-A is generated by fixing 850Mhz clock. All output clocks use PLL-A to
* generate the frequency. This is the method used in QRP radios such as uBITX.
* When switching to WSPR transmission mode, PLL-B operates for the base frequency to transmit WSPR.
* The output clock channel that controls the frequency is connected to the PLL-B.
* The WSPR protocol is generated by changing the clock of the PLL-B.
************************************************************************************/
// ************* SI5315 routines - tks Jerry Gaffke, KE7ER ***********************
// An minimalist standalone set of Si5351 routines.
// VCOA is fixed at 875mhz, VCOB not used.
// The output msynth dividers are used to generate 3 independent clocks
// with 1hz resolution to any frequency between 4khz and 109mhz.
// Usage:
// Call si5351bx_init() once at startup with no args;
// Call si5351bx_setfreq(clknum, freq) each time one of the
// three output CLK pins is to be updated to a new frequency.
// A freq of 0 serves to shut down that output clock.
// The global variable si5351bx_vcoa starts out equal to the nominal VCOA
// frequency of 25mhz*35 = 875000000 Hz. To correct for 25mhz crystal errors,
// the user can adjust this value. The vco frequency will not change but
// the number used for the (a+b/c) output msynth calculations is affected.
// Example: We call for a 5mhz signal, but it measures to be 5.001mhz.
// So the actual vcoa frequency is 875mhz*5.001/5.000 = 875175000 Hz,
// To correct for this error: si5351bx_vcoa=875175000;
// Most users will never need to generate clocks below 500khz.
// But it is possible to do so by loading a value between 0 and 7 into
// the global variable si5351bx_rdiv, be sure to return it to a value of 0
// before setting some other CLK output pin. The affected clock will be
// divided down by a power of two defined by 2**si5351_rdiv
// A value of zero gives a divide factor of 1, a value of 7 divides by 128.
// This lightweight method is a reasonable compromise for a seldom used feature.
#define BB0(x) ((uint8_t)x) // Bust int32 into Bytes
#define BB1(x) ((uint8_t)(x>>8))
#define BB2(x) ((uint8_t)(x>>16))
#define SI5351BX_ADDR 0x60 // I2C address of Si5351 (typical)
#define SI5351BX_XTALPF 2 // 1:6pf 2:8pf 3:10pf
// If using 27mhz crystal, set XTAL=27000000, MSA=33. Then vco=891mhz
#define SI5351BX_XTAL 25000000 // Crystal freq in Hz
#define SI5351BX_MSA 35 // VCOA is at 25mhz*35 = 875mhz
// User program may have reason to poke new values into these 3 RAM variables
uint32_t si5351bx_vcoa = (SI5351BX_XTAL*SI5351BX_MSA); // 25mhzXtal calibrate
uint8_t si5351bx_rdiv = 0; // 0-7, CLK pin sees fout/(2**rdiv)
uint8_t si5351bx_drive[3] = {1, 1, 1}; // 0=2ma 1=4ma 2=6ma 3=8ma for CLK 0,1,2
uint8_t si5351bx_clken = 0xFF; // Private, all CLK output drivers off
int32_t calibration = 0;
void i2cWrite(uint8_t reg, uint8_t val) { // write reg via i2c
Wire.beginTransmission(SI5351BX_ADDR);
Wire.write(reg);
Wire.write(val);
Wire.endTransmission();
}
void i2cWriten(uint8_t reg, uint8_t *vals, uint8_t vcnt) { // write array
Wire.beginTransmission(SI5351BX_ADDR);
Wire.write(reg);
while (vcnt--) Wire.write(*vals++);
Wire.endTransmission();
}
uint8_t si5351Val[8] = {0, 1, 0, 0, 0, 0, 0, 0}; //for reduce program memory size
void si5351bx_init() { // Call once at power-up, start PLLA
uint32_t msxp1;
Wire.begin();
i2cWrite(149, 0); // SpreadSpectrum off
i2cWrite(3, si5351bx_clken); // Disable all CLK output drivers
i2cWrite(183, SI5351BX_XTALPF << 6); // Set 25mhz crystal load capacitance
msxp1 = 128 * SI5351BX_MSA - 512; // and msxp2=0, msxp3=1, not fractional
//uint8_t vals[8] = {0, 1, BB2(msxp1), BB1(msxp1), BB0(msxp1), 0, 0, 0};
si5351Val[2] = BB2(msxp1);
si5351Val[3] = BB1(msxp1);
si5351Val[4] = BB0(msxp1);
i2cWriten(26, si5351Val, 8); // Write to 8 PLLA msynth regs
i2cWrite(177, 0x20); // Reset PLLA (0x80 resets PLLB)
}
void si5351bx_setfreq(uint8_t clknum, uint32_t fout) { // Set a CLK to fout Hz
uint32_t msa, msb, msc, msxp1, msxp2, msxp3p2top;
if ((fout < 500000) || (fout > 109000000)) // If clock freq out of range
si5351bx_clken |= 1 << clknum; // shut down the clock
else {
msa = si5351bx_vcoa / fout; // Integer part of vco/fout
msb = si5351bx_vcoa % fout; // Fractional part of vco/fout
msc = fout; // Divide by 2 till fits in reg
while (msc & 0xfff00000) {
msb = msb >> 1;
msc = msc >> 1;
}
msxp1 = (128 * msa + 128 * msb / msc - 512) | (((uint32_t)si5351bx_rdiv) << 20);
msxp2 = 128 * msb - 128 * msb / msc * msc; // msxp3 == msc;
msxp3p2top = (((msc & 0x0F0000) << 4) | msxp2); // 2 top nibbles
uint8_t vals[8] = { BB1(msc), BB0(msc), BB2(msxp1), BB1(msxp1),
BB0(msxp1), BB2(msxp3p2top), BB1(msxp2), BB0(msxp2)
};
i2cWriten(42 + (clknum * 8), vals, 8); // Write to 8 msynth regs
i2cWrite(16 + clknum, 0x0C | si5351bx_drive[clknum]); // use local msynth
si5351bx_clken &= ~(1 << clknum); // Clear bit to enable clock
}
i2cWrite(3, si5351bx_clken); // Enable/disable clock
}
void si5351_set_calibration(int32_t cal){
si5351bx_vcoa = (SI5351BX_XTAL * SI5351BX_MSA) + cal; // apply the calibration correction factor
si5351bx_setfreq(0, usbCarrier);
}
void SetCarrierFreq()
{
unsigned long appliedCarrier = ((cwMode == 0 ? usbCarrier : cwmCarrier) + (isIFShift && (inTx == 0) ? ifShiftValue : 0));
si5351bx_setfreq(0, appliedCarrier);
/*
if (cwMode == 0)
si5351bx_setfreq(0, usbCarrier + (isIFShift ? ifShiftValue : 0));
else
si5351bx_setfreq(0, cwmCarrier + (isIFShift ? ifShiftValue : 0));
*/
}
void initOscillators(){
//initialize the SI5351
si5351bx_init();
si5351bx_vcoa = (SI5351BX_XTAL * SI5351BX_MSA) + calibration; // apply the calibration correction factor
SetCarrierFreq();
}
//============================================================
// ADD FUNCTIONS by KD8CEC
//============================================================
uint8_t Wspr_Reg1[8] = {0xFF,0xFE, 0x00, 0, 0, 0, 0, 0}; //3, 4, 5, 6, 7
uint8_t Wspr_Reg2[8] = {0, 1, 0, 0, 0, 0, 0, 0}; //2, 3, 4
void Set_WSPR_Param(void)
{
i2cWrite(18, 128);
i2cWriten(34, Wspr_Reg1, 8);
i2cWriten(58, Wspr_Reg2, 8);
i2cWrite(177, 128);
i2cWrite(18, 111);
si5351bx_clken &= ~(1 << 2);
i2cWrite(3, si5351bx_clken);
}
void TXSubFreq(unsigned long P2)
{
i2cWrite(40, (P2 & 65280) >> 8);
i2cWrite(41, P2 & 255);
}