/*************************************************************************
  header file for C++ by KD8CEC
-----------------------------------------------------------------------------
   This program is free software: you can redistribute it and/or modify
   it under the terms of the GNU General Public License as published by
   the Free Software Foundation, either version 3 of the License, or
   (at your option) any later version.

   This program is distributed in the hope that it will be useful,
   but WITHOUT ANY WARRANTY; without even the implied warranty of
   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
   GNU General Public License for more details.

   You should have received a copy of the GNU General Public License
   along with this program.  If not, see <http://www.gnu.org/licenses/>.
**************************************************************************/
#ifndef _UBITX_HEADER__
#define _UBITX_HEADER__

#include <Arduino.h>  //for Linux, On Linux it is case sensitive.

//==============================================================================
// Compile-Time Options
//==============================================================================
// uBITX Board Version - KC4UPR: updated to v5
#define UBITX_BOARD_VERSION 5           //v1 ~ v4 : 4, v5: 5

//Depending on the type of LCD mounted on the uBITX, uncomment one of the options below.
//You must select only one.
//#define UBITX_DISPLAY_LCD1602P        //LCD mounted on unmodified uBITX (Parallel)
//#define UBITX_DISPLAY_LCD1602I        //I2C type 16 x 02 LCD
//#define UBITX_DISPLAY_LCD1602I_DUAL   //I2C type 16 x02 LCD Dual
//#define UBITX_DISPLAY_LCD2004P        //24 x 04 LCD (Parallel)
//#define UBITX_DISPLAY_LCD2004I        //I2C type 24 x 04 LCD
#define UBITX_DISPLAY_NEXTION         //NEXTION LCD

//#define UBITX_DISPLAY_NEXTION_SAFE      //Only EEProm Write 770~775
#define I2C_LCD_MASTER_ADDRESS_DEFAULT  0x27     //0x27  //DEFAULT, if Set I2C Address by uBITX Manager, read from EEProm
#define I2C_LCD_SECOND_ADDRESS_DEFAULT  0x3F     //0x27  //only using Dual LCD Mode

//Select betwen Analog S-Meter and DSP (I2C) Meter
#define USE_I2CSMETER

#define EXTEND_KEY_GROUP1               //MODE, BAND(-), BAND(+), STEP
//#define EXTEND_KEY_GROUP2             //Numeric (0~9), Point(.), Enter  //Not supported in Version 1.0x

//Custom LPF Filter Mod
//#define USE_CUSTOM_LPF_FILTER           //LPF FILTER MOD

//#define ENABLE_FACTORYALIGN
#define FACTORY_RECOVERY_BOOTUP         //Whether to enter Factory Recovery mode by pressing FKey and turning on power
#define ENABLE_ADCMONITOR               //Starting with Version 1.07, you can read ADC values directly from uBITX Manager. So this function is not necessary.

extern byte I2C_LCD_MASTER_ADDRESS;     //0x27  //if Set I2C Address by uBITX Manager, read from EEProm
extern byte I2C_LCD_SECOND_ADDRESS;     //only using Dual LCD Mode
#define SMeterLatency   3               //1 is 0.25 sec

//==============================================================================
// User Select feather list
//==============================================================================
//Enable all features
#define FN_BAND         1 //592
#define FN_VFO_TOGGLE   1 //78
#define FN_MODE         1 //20
#define FN_RIT          1 //58
#define FN_SPLIT        1 //62
#define FN_IFSHIFT      1 //238
#define FN_ATT          1 //128
#define FN_CW_SPEED     1 //152
#define FN_VFOTOMEM     1 //254
#define FN_MEMTOVFO     1 //188
#define FN_MEMORYKEYER  1 //156
#define FN_WSPR         1 //1044
#define FN_SDRMODE      1 //68
#define FN_CALIBRATION  1 //666
#define FN_CARRIER      1 //382
#define FN_CWCARRIER    1 //346
#define FN_CWTONE       1 //148
#define FN_CWDELAY      1 //98
#define FN_TXCWDELAY    1 //94
#define FN_KEYTYPE      1 //168
#define FN_ADCMONITOR   1 //516
#define FN_TXONOFF      1 //58

/*
//Test Configuration  (88%)
#define FN_BAND         0 //592
#define FN_VFO_TOGGLE   0 //78
#define FN_MODE         0 //20
#define FN_RIT          0 //58
#define FN_SPLIT        0 //62
#define FN_IFSHIFT      0 //238
#define FN_ATT          0 //128
#define FN_CW_SPEED     1 //152
#define FN_VFOTOMEM     0 //254
#define FN_MEMTOVFO     0 //188
#define FN_MEMORYKEYER  1 //156
#define FN_WSPR         0 //1044
#define FN_SDRMODE      1 //68
#define FN_CALIBRATION  1 //666
#define FN_CARRIER      1 //382
#define FN_CWCARRIER    1 //346
#define FN_CWTONE       1 //148
#define FN_CWDELAY      1 //98
#define FN_TXCWDELAY    1 //94
#define FN_KEYTYPE      1 //168
#define FN_ADCMONITOR   1 //516
#define FN_TXONOFF      1 //58
*/

/*
//Recommended Character LCD Developer  87%
#define FN_BAND         1 //592
#define FN_VFO_TOGGLE   1 //78
#define FN_MODE         1 //20
#define FN_RIT          1 //58
#define FN_SPLIT        1 //62
#define FN_IFSHIFT      1 //238
#define FN_ATT          0 //128
#define FN_CW_SPEED     0 //152 //using MM
#define FN_VFOTOMEM     1 //254
#define FN_MEMTOVFO     1 //188
#define FN_MEMORYKEYER  1 //156
#define FN_WSPR         1 //1044
#define FN_SDRMODE      1 //68
#define FN_CALIBRATION  0 //667 //using MM
#define FN_CARRIER      0 //382 //using MM
#define FN_CWCARRIER    0 //346 //using MM
#define FN_CWTONE       0 //148 //using MM
#define FN_CWDELAY      0 //98 //using MM
#define FN_TXCWDELAY    0 //94 //using MM
#define FN_KEYTYPE      0 //168 //using MM
#define FN_ADCMONITOR   0 //516 //using MM
#define FN_TXONOFF      1 //58
*/

/*
//Recommended for Nextion, TJC LCD 88%
#define FN_BAND         1 //600
#define FN_VFO_TOGGLE   1 //90
#define FN_MODE         1 //318
#define FN_RIT          1 //62
#define FN_SPLIT        1 //2
#define FN_IFSHIFT      1 //358
#define FN_ATT          1 //250
#define FN_CW_SPEED     0 //286
#define FN_VFOTOMEM     0 //276
#define FN_MEMTOVFO     0 //234
#define FN_MEMORYKEYER  1 //168
#define FN_WSPR         1 //1130
#define FN_SDRMODE      1 //70
#define FN_CALIBRATION  0 //790
#define FN_CARRIER      0 //500
#define FN_CWCARRIER    0 //464
#define FN_CWTONE       0 //158
#define FN_CWDELAY      0 //108
#define FN_TXCWDELAY    0 //106
#define FN_KEYTYPE      0 //294
#define FN_ADCMONITOR   0 //526 //not available with Nextion or Serial UI
#define FN_TXONOFF      1 //70
*/
//==============================================================================
// End of User Select Mode and Compil options
//==============================================================================

#ifdef UBITX_DISPLAY_LCD1602I
  #define USE_I2C_LCD
#elif defined(UBITX_DISPLAY_LCD1602I_DUAL)
  #define USE_I2C_LCD
#elif defined(UBITX_DISPLAY_LCD2004I)
  #define USE_I2C_LCD
#endif

#ifdef UBITX_DISPLAY_NEXTION
  #define USE_SW_SERIAL
  #undef ENABLE_ADCMONITOR
  #undef FACTORY_RECOVERY_BOOTUP  
#elif defined(UBITX_CONTROL_MCU)
  #define USE_SW_SERIAL
  #undef ENABLE_ADCMONITOR
  #undef FACTORY_RECOVERY_BOOTUP  
#endif


//==============================================================================
// Hardware, Define PIN Usage
//==============================================================================
/**
 * We need to carefully pick assignment of pin for various purposes.
 * There are two sets of completely programmable pins on the Raduino.
 * First, on the top of the board, in line with the LCD connector is an 8-pin connector
 * that is largely meant for analog inputs and front-panel control. It has a regulated 5v output,
 * ground and six pins. Each of these six pins can be individually programmed 
 * either as an analog input, a digital input or a digital output. 
 * The pins are assigned as follows (left to right, display facing you): 
 *      Pin 1 (Violet), A7, SPARE => Analog S-Meter
 *      Pin 2 (Blue),   A6, KEYER (DATA)
 *      Pin 3 (Green), +5v 
 *      Pin 4 (Yellow), Gnd
 *      Pin 5 (Orange), A3, PTT
 *      Pin 6 (Red),    A2, F BUTTON
 *      Pin 7 (Brown),  A1, ENC B
 *      Pin 8 (Black),  A0, ENC A
 *Note: A5, A4 are wired to the Si5351 as I2C interface 
 *       *     
 * Though, this can be assigned anyway, for this application of the Arduino, we will make the following
 * assignment
 * A2 will connect to the PTT line, which is the usually a part of the mic connector
 * A3 is connected to a push button that can momentarily ground this line. This will be used for RIT/Bandswitching, etc.
 * A6 is to implement a keyer, it is reserved and not yet implemented
 * A7 is connected to a center pin of good quality 100K or 10K linear potentiometer with the two other ends connected to
 * ground and +5v lines available on the connector. This implments the tuning mechanism
 */
#define ENC_A         (A0)
#define ENC_B         (A1)
#define FBUTTON       (A2)
#define PTT           (A3)  // 8?
#define DIGITAL_KEY   (A3)  // 8?
#define DIGITAL_DOT   (12)
#define DIGITAL_DASH  (11)
#define ANALOG_KEYER  (A6)
#define ANALOG_SPARE  (A7)
#define ANALOG_SMETER (A7)  //by KD8CEC

/** 
 *  The second set of 16 pins on the Raduino's bottom connector are have the three clock outputs and the digital lines to control the rig.
 *  This assignment is as follows :
 *    Pin   1   2    3    4    5    6    7    8    9    10   11   12   13   14   15   16
 *         GND +5V CLK2  GND  GND  CLK1 GND  GND  CLK0  GND  D2   D3   D4   D5   D6   D7  
 *  These too are flexible with what you may do with them, for the Raduino, we use them to :
 *  - TX_RX line : Switches between Transmit and Receive after sensing the PTT or the morse keyer
 *  - CW_KEY line : turns on the carrier for CW
 */
#define TX_RX         (7)   //Relay
#define CW_TONE       (6)
#define TX_LPF_A      (5)   //Relay
#define TX_LPF_B      (4)   //Relay
#define TX_LPF_C      (3)   //Relay
#define CW_KEY        (2)

//******************************************************
//DSP (I2C) Meter 
//******************************************************
//S-Meter Address
#define I2CMETER_ADDR     0x58
//VALUE TYPE============================================
//Signal
#define I2CMETER_CALCS    0x59 //Calculated Signal Meter
#define I2CMETER_UNCALCS  0x58 //Uncalculated Signal Meter

//Power
#define I2CMETER_CALCP    0x57 //Calculated Power Meter
#define I2CMETER_UNCALCP  0x56 //UnCalculated Power Meter

//SWR
#define I2CMETER_CALCR    0x55 //Calculated SWR Meter
#define I2CMETER_UNCALCR  0x54 //Uncalculated SWR Meter

//==============================================================================
// for public, Variable, functions
//==============================================================================
#define WSPR_BAND_COUNT 3
#define TX_SSB          0
#define TX_CW           1
#define printLineF1(x) (printLineF(1, x))
#define printLineF2(x) (printLineF(0, x))

//0x00 : None, 0x01 : MODE, 0x02:BAND+, 0x03:BAND-, 0x04:TUNE_STEP, 0x05:VFO Toggle, 0x06:SplitOn/Off, 0x07:TX/ON-OFF,  0x08:SDR Mode On / Off, 0x09:Rit Toggle
#define FUNCTION_KEY_ADC  80  //MODE, BAND(-), BAND(+), STEP
#define FKEY_PRESS      0x78
#define FKEY_MODE       0x01
#define FKEY_BANDUP     0x02
#define FKEY_BANDDOWN   0x03
#define FKEY_STEP       0x04
#define FKEY_VFOCHANGE  0x05
#define FKEY_SPLIT      0x06
#define FKEY_TXOFF      0x07
#define FKEY_SDRMODE    0x08
#define FKEY_RIT        0x09

#define FKEY_ENTER      0x0A
#define FKEY_POINT      0x0B
#define FKEY_DELETE     0x0C
#define FKEY_CANCEL     0x0D

#define FKEY_NUM0       0x10
#define FKEY_NUM1       0x11
#define FKEY_NUM2       0x12
#define FKEY_NUM3       0x13
#define FKEY_NUM4       0x14
#define FKEY_NUM5       0x15
#define FKEY_NUM6       0x16
#define FKEY_NUM7       0x17
#define FKEY_NUM8       0x18
#define FKEY_NUM9       0x19

#define FKEY_TYPE_MAX   0x1F

extern uint8_t SI5351BX_ADDR;     //change typical -> variable at Version 1.097, address read from eeprom, default value is 0x60
                                  //EEProm Address : 63
extern unsigned long frequency;
extern byte WsprMSGCount;
extern byte sMeterLevels[9];
extern int currentSMeter;         //ADC Value for S.Meter
extern byte scaledSMeter;         //Calculated S.Meter Level

extern byte KeyValues[16][3];     //Set : Start Value, End Value, Key Type, 16 Set (3 * 16 = 48)
extern byte TriggerBySW;   //Action Start from Nextion LCD, Other MCU

extern void printLine1(const char *c);
extern void printLine2(const char *c);
extern void printLineF(char linenmbr, const __FlashStringHelper *c);
extern void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetType);
extern byte delay_background(unsigned delayTime, byte fromType);
extern int btnDown(void);
extern char c[30];
extern char b[30];
extern int enc_read(void);
extern void si5351bx_init(void);
extern void si5351bx_setfreq(uint8_t clknum, uint32_t fout);
extern void si5351_set_calibration(int32_t cal);
extern void initOscillators(void);
extern void Set_WSPR_Param(void);
extern void TXSubFreq(unsigned long P2);

extern void startTx(byte txMode, byte isDisplayUpdate);
extern void stopTx(void);
extern void setTXFilters(unsigned long freq);

extern void SendWSPRManage(void);
extern char byteToChar(byte srcByte);
extern void DisplayCallsign(byte callSignLength);
extern void DisplayVersionInfo(const char* fwVersionInfo);

//I2C Signal Meter, Version 1.097
extern int GetI2CSmeterValue(int valueType);  //ubitx_ui.ino

#endif    //end of if header define