136 lines
6.7 KiB
C
136 lines
6.7 KiB
C
/*************************************************************************
|
|
header file for EEProm Address Map by KD8CEC
|
|
It must be protected to protect the factory calibrated calibration.
|
|
-----------------------------------------------------------------------------
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
**************************************************************************/
|
|
#ifndef _UBITX_EEPOM_HEADER__
|
|
#define _UBITX_EEPOM_HEADER__
|
|
|
|
//==============================================================================
|
|
// Factory-shipped EEProm address
|
|
// (factory Firmware)
|
|
// Address : 0 ~ 31
|
|
//==============================================================================
|
|
#define MASTER_CAL 0
|
|
#define LSB_CAL 4
|
|
#define USB_CAL 8
|
|
#define SIDE_TONE 12
|
|
//these are ids of the vfos as well as their offset into the eeprom storage, don't change these 'magic' values
|
|
#define VFO_A 16
|
|
#define VFO_B 20
|
|
#define CW_SIDETONE 24
|
|
#define CW_SPEED 28
|
|
|
|
//==============================================================================
|
|
// The spare space available in the original firmware #1
|
|
// Address : 32 ~ 63
|
|
//==============================================================================
|
|
#define RESERVE_FOR_FACTORY1 32
|
|
|
|
//==============================================================================
|
|
// The spare space available in the original firmware #2
|
|
// (Enabled if the EEProm address is insufficient)
|
|
// Address : 64 ~ 100
|
|
//==============================================================================
|
|
#define RESERVE_FOR_FACTORY2 64 //use Factory backup from Version 1.075
|
|
#define FACTORY_BACKUP_YN 64 //Check Backup //Magic : 0x13
|
|
#define FACTORY_VALUES 65 //65 ~ 65 + 32
|
|
|
|
//==============================================================================
|
|
// KD8CEC EEPROM MAP
|
|
// Address : 101 ~ 1023
|
|
// 256 is the base address
|
|
// 256 ~ 1023 (EEProm Section #1)
|
|
// 255 ~ 101 (EEProm Section #2)
|
|
//==============================================================================
|
|
|
|
//0x00 : None, 0x01 : MODE, 0x02:BAND+, 0x03:BAND-, 0x04:TUNE_STEP, 0x05:VFO Toggle, 0x06:SplitOn/Off, 0x07:TX/ON-OFF, 0x08:SDR Mode On / Off, 0x09:Rit Toggle
|
|
#define EXTENDED_KEY_RANGE 140 //Extended Key => Set : Start Value, End Value, Key Type, 16 Set (3 * 16 = 48)
|
|
|
|
#define I2C_LCD_MASTER 190
|
|
#define I2C_LCD_SECOND 191
|
|
|
|
#define S_METER_LEVELS 230 //LEVEL0 ~ LEVEL7
|
|
|
|
#define ADVANCED_FREQ_OPTION1 240 //Bit0: use IFTune_Value, Bit1 : use Stored enabled SDR Mode, Bit2 : dynamic sdr frequency
|
|
#define IF1_CAL 241
|
|
#define ENABLE_SDR 242
|
|
#define SDR_FREQUNCY 243
|
|
#define CW_CAL 252
|
|
|
|
#define VFO_A_MODE 256
|
|
#define VFO_B_MODE 257
|
|
#define CW_DELAY 258
|
|
#define CW_START 259
|
|
#define HAM_BAND_COUNT 260 //
|
|
#define TX_TUNE_TYPE 261 //
|
|
#define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
|
|
#define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
|
|
#define TUNING_STEP 342 //TUNING STEP * 6 (index 1 + STEPS 5) //1STEP :
|
|
|
|
//for reduce cw key error, eeprom address
|
|
#define CW_ADC_MOST_BIT1 348 //most 2bits of DOT_TO , DOT_FROM, ST_TO, ST_FROM
|
|
#define CW_ADC_ST_FROM 349 //CW ADC Range STRAIGHT KEY from (Lower 8 bit)
|
|
#define CW_ADC_ST_TO 350 //CW ADC Range STRAIGHT KEY to (Lower 8 bit)
|
|
#define CW_ADC_DOT_FROM 351 //CW ADC Range DOT from (Lower 8 bit)
|
|
#define CW_ADC_DOT_TO 352 //CW ADC Range DOT to (Lower 8 bit)
|
|
|
|
#define CW_ADC_MOST_BIT2 353 //most 2bits of BOTH_TO, BOTH_FROM, DASH_TO, DASH_FROM
|
|
#define CW_ADC_DASH_FROM 354 //CW ADC Range DASH from (Lower 8 bit)
|
|
#define CW_ADC_DASH_TO 355 //CW ADC Range DASH to (Lower 8 bit)
|
|
#define CW_ADC_BOTH_FROM 356 //CW ADC Range BOTH from (Lower 8 bit)
|
|
#define CW_ADC_BOTH_TO 357 //CW ADC Range BOTH to (Lower 8 bit)
|
|
#define CW_KEY_TYPE 358
|
|
#define CW_DISPLAY_SHIFT 359 //Transmits on CWL, CWU Mode, LCD Frequency shifts Sidetone Frequency.
|
|
//(7:Enable / Disable //0: enable, 1:disable, (default is applied shift)
|
|
//6 : 0 : Adjust Pulus, 1 : Adjust Minus
|
|
//0~5: Adjust Value : * 10 = Adjust Value (0~300)
|
|
#define COMMON_OPTION0 360 //0: Confirm : CW Frequency Shift
|
|
//1 : IF Shift Save
|
|
#define IF_SHIFTVALUE 363
|
|
|
|
#define DISPLAY_OPTION1 361 //Display Option1
|
|
#define DISPLAY_OPTION2 362 //Display Option2
|
|
|
|
#define WSPR_COUNT 443 //WSPR_MESSAGE_COUNT
|
|
#define WSPR_MESSAGE1 444 //
|
|
#define WSPR_MESSAGE2 490 //
|
|
#define WSPR_MESSAGE3 536 //
|
|
#define WSPR_MESSAGE4 582 //
|
|
|
|
#define CHANNEL_FREQ 630 //Channel 1 ~ 20, 1 Channel = 4 bytes
|
|
#define CHANNEL_DESC 710 //Channel 1 ~ 20, 1 Channel = 4 bytes
|
|
#define EXTERNAL_DEVICE_OPT1 770 //for External Deivce 4byte
|
|
#define EXTERNAL_DEVICE_OPT2 774 //for External Deivce 2byte
|
|
|
|
//Check Firmware type and version
|
|
#define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
|
|
#define VERSION_ADDRESS 779 //check Firmware version
|
|
//USER INFORMATION
|
|
#define USER_CALLSIGN_KEY 780 //0x59
|
|
#define USER_CALLSIGN_LEN 781 //1BYTE (OPTION + LENGTH) + CALLSIGN (MAXIMUM 18)
|
|
#define USER_CALLSIGN_DAT 782 //CALL SIGN DATA //direct EEPROM to LCD basic offset
|
|
|
|
//AUTO KEY STRUCTURE
|
|
//AUTO KEY USE 800 ~ 1023
|
|
#define CW_AUTO_MAGIC_KEY 800 //0x73
|
|
#define CW_AUTO_COUNT 801 //0 ~ 255
|
|
#define CW_AUTO_DATA 803 //[INDEX, INDEX, INDEX,DATA,DATA, DATA (Positon offset is CW_AUTO_DATA
|
|
#define CW_DATA_OFSTADJ CW_AUTO_DATA - USER_CALLSIGN_DAT //offset adjust for ditect eeprom to lcd (basic offset is USER_CALLSIGN_DAT
|
|
#define CW_STATION_LEN 1023 //value range : 4 ~ 30
|
|
|
|
#endif //end of if header define
|
|
|