185 lines
7.9 KiB
C
185 lines
7.9 KiB
C
/*************************************************************************
|
|
header file for C++ by KD8CEC
|
|
-----------------------------------------------------------------------------
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
**************************************************************************/
|
|
#ifndef _UBITX_HEADER__
|
|
#define _UBITX_HEADER__
|
|
|
|
#include <Arduino.h> //for Linux, On Linux it is case sensitive.
|
|
|
|
//==============================================================================
|
|
// Compile Option
|
|
//==============================================================================
|
|
//Depending on the type of LCD mounted on the uBITX, uncomment one of the options below.
|
|
//You must select only one.
|
|
#define UBITX_DISPLAY_LCD1602P //LCD mounted on unmodified uBITX (Parallel)
|
|
//#define UBITX_DISPLAY_LCD1602I //I2C type 16 x 02 LCD
|
|
//#define UBITX_DISPLAY_LCD1602I_DUAL //I2C type 16 x02 LCD Dual
|
|
//#define UBITX_DISPLAY_LCD2004P //24 x 04 LCD (Parallel)
|
|
//#define UBITX_DISPLAY_LCD2004I //I2C type 24 x 04 LCD
|
|
|
|
#define I2C_LCD_MASTER_ADDRESS_DEFAULT 0x3F //0x27 //DEFAULT, if Set I2C Address by uBITX Manager, read from EEProm
|
|
#define I2C_LCD_SECOND_ADDRESS_DEFAULT 0x27 //0x27 //only using Dual LCD Mode
|
|
|
|
#define EXTEND_KEY_GROUP1 //MODE, BAND(-), BAND(+), STEP
|
|
//#define EXTEND_KEY_GROUP2 //Numeric (0~9), Point(.), Enter //Not supported in Version 1.0x
|
|
|
|
//#define ENABLE_FACTORYALIGN
|
|
#define FACTORY_RECOVERY_BOOTUP //Whether to enter Factory Recovery mode by pressing FKey and turning on power
|
|
#define ENABLE_ADCMONITOR //Starting with Version 1.07, you can read ADC values directly from uBITX Manager. So this function is not necessary.
|
|
|
|
extern byte I2C_LCD_MASTER_ADDRESS; //0x27 //if Set I2C Address by uBITX Manager, read from EEProm
|
|
extern byte I2C_LCD_SECOND_ADDRESS; //only using Dual LCD Mode
|
|
|
|
#define SMeterLatency 3 //1 is 0.25 sec
|
|
|
|
#ifdef UBITX_DISPLAY_LCD1602I
|
|
#define USE_I2C_LCD
|
|
#elif defined(UBITX_DISPLAY_LCD1602I_DUAL)
|
|
#define USE_I2C_LCD
|
|
#elif defined(UBITX_DISPLAY_LCD2004I)
|
|
#define USE_I2C_LCD
|
|
#endif
|
|
|
|
//==============================================================================
|
|
// Hardware, Define PIN Usage
|
|
//==============================================================================
|
|
/**
|
|
* We need to carefully pick assignment of pin for various purposes.
|
|
* There are two sets of completely programmable pins on the Raduino.
|
|
* First, on the top of the board, in line with the LCD connector is an 8-pin connector
|
|
* that is largely meant for analog inputs and front-panel control. It has a regulated 5v output,
|
|
* ground and six pins. Each of these six pins can be individually programmed
|
|
* either as an analog input, a digital input or a digital output.
|
|
* The pins are assigned as follows (left to right, display facing you):
|
|
* Pin 1 (Violet), A7, SPARE
|
|
* Pin 2 (Blue), A6, KEYER (DATA)
|
|
* Pin 3 (Green), +5v
|
|
* Pin 4 (Yellow), Gnd
|
|
* Pin 5 (Orange), A3, PTT
|
|
* Pin 6 (Red), A2, F BUTTON
|
|
* Pin 7 (Brown), A1, ENC B
|
|
* Pin 8 (Black), A0, ENC A
|
|
*Note: A5, A4 are wired to the Si5351 as I2C interface
|
|
* *
|
|
* Though, this can be assigned anyway, for this application of the Arduino, we will make the following
|
|
* assignment
|
|
* A2 will connect to the PTT line, which is the usually a part of the mic connector
|
|
* A3 is connected to a push button that can momentarily ground this line. This will be used for RIT/Bandswitching, etc.
|
|
* A6 is to implement a keyer, it is reserved and not yet implemented
|
|
* A7 is connected to a center pin of good quality 100K or 10K linear potentiometer with the two other ends connected to
|
|
* ground and +5v lines available on the connector. This implments the tuning mechanism
|
|
*/
|
|
#define ENC_A (A0)
|
|
#define ENC_B (A1)
|
|
#define FBUTTON (A2)
|
|
#define PTT (A3)
|
|
#define ANALOG_KEYER (A6)
|
|
#define ANALOG_SPARE (A7)
|
|
#define ANALOG_SMETER (A7) //by KD8CEC
|
|
|
|
/**
|
|
* The second set of 16 pins on the Raduino's bottom connector are have the three clock outputs and the digital lines to control the rig.
|
|
* This assignment is as follows :
|
|
* Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
|
|
* GND +5V CLK0 GND GND CLK1 GND GND CLK2 GND D2 D3 D4 D5 D6 D7
|
|
* These too are flexible with what you may do with them, for the Raduino, we use them to :
|
|
* - TX_RX line : Switches between Transmit and Receive after sensing the PTT or the morse keyer
|
|
* - CW_KEY line : turns on the carrier for CW
|
|
*/
|
|
#define TX_RX (7) //Relay
|
|
#define CW_TONE (6)
|
|
#define TX_LPF_A (5) //Relay
|
|
#define TX_LPF_B (4) //Relay
|
|
#define TX_LPF_C (3) //Relay
|
|
#define CW_KEY (2)
|
|
|
|
//==============================================================================
|
|
// for public, Variable, functions
|
|
//==============================================================================
|
|
#define WSPR_BAND_COUNT 3
|
|
#define TX_SSB 0
|
|
#define TX_CW 1
|
|
#define printLineF1(x) (printLineF(1, x))
|
|
#define printLineF2(x) (printLineF(0, x))
|
|
|
|
//0x00 : None, 0x01 : MODE, 0x02:BAND+, 0x03:BAND-, 0x04:TUNE_STEP, 0x05:VFO Toggle, 0x06:SplitOn/Off, 0x07:TX/ON-OFF, 0x08:SDR Mode On / Off, 0x09:Rit Toggle
|
|
#define FUNCTION_KEY_ADC 80 //MODE, BAND(-), BAND(+), STEP
|
|
#define FKEY_PRESS 0x78
|
|
#define FKEY_MODE 0x01
|
|
#define FKEY_BANDUP 0x02
|
|
#define FKEY_BANDDOWN 0x03
|
|
#define FKEY_STEP 0x04
|
|
#define FKEY_VFOCHANGE 0x05
|
|
#define FKEY_SPLIT 0x06
|
|
#define FKEY_TXOFF 0x07
|
|
#define FKEY_SDRMODE 0x08
|
|
#define FKEY_RIT 0x09
|
|
|
|
#define FKEY_ENTER 0x0A
|
|
#define FKEY_POINT 0x0B
|
|
#define FKEY_DELETE 0x0C
|
|
#define FKEY_CANCEL 0x0D
|
|
|
|
#define FKEY_NUM0 0x10
|
|
#define FKEY_NUM1 0x11
|
|
#define FKEY_NUM2 0x12
|
|
#define FKEY_NUM3 0x13
|
|
#define FKEY_NUM4 0x14
|
|
#define FKEY_NUM5 0x15
|
|
#define FKEY_NUM6 0x16
|
|
#define FKEY_NUM7 0x17
|
|
#define FKEY_NUM8 0x18
|
|
#define FKEY_NUM9 0x19
|
|
|
|
#define FKEY_TYPE_MAX 0x1F
|
|
|
|
extern unsigned long frequency;
|
|
extern byte WsprMSGCount;
|
|
extern byte sMeterLevels[9];
|
|
extern int currentSMeter; //ADC Value for S.Meter
|
|
extern byte scaledSMeter; //Calculated S.Meter Level
|
|
|
|
extern byte KeyValues[16][3]; //Set : Start Value, End Value, Key Type, 16 Set (3 * 16 = 48)
|
|
|
|
extern void printLine1(const char *c);
|
|
extern void printLine2(const char *c);
|
|
extern void printLineF(char linenmbr, const __FlashStringHelper *c);
|
|
extern void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex, char offsetType);
|
|
extern byte delay_background(unsigned delayTime, byte fromType);
|
|
extern int btnDown(void);
|
|
extern char c[30];
|
|
extern char b[30];
|
|
extern int enc_read(void);
|
|
extern void si5351bx_init(void);
|
|
extern void si5351bx_setfreq(uint8_t clknum, uint32_t fout);
|
|
extern void si5351_set_calibration(int32_t cal);
|
|
extern void initOscillators(void);
|
|
extern void Set_WSPR_Param(void);
|
|
extern void TXSubFreq(unsigned long P2);
|
|
|
|
extern void startTx(byte txMode, byte isDisplayUpdate);
|
|
extern void stopTx(void);
|
|
extern void setTXFilters(unsigned long freq);
|
|
|
|
extern void SendWSPRManage(void);
|
|
extern char byteToChar(byte srcByte);
|
|
extern void DisplayCallsign(byte callSignLength);
|
|
extern void DisplayVersionInfo(const char* fwVersionInfo);
|
|
|
|
#endif //end of if header define
|
|
|
|
|