Merge branch 'master' into version0.29

Fixed most compilation warnings and a delay issue

README.md

@@ -1,7 +1,21 @@
 #IMPORTANT INFORMATION
 ----------------------------------------------------------------------------
-- Beta 0.26 and Beta 0.261, Beta 0.262, Beta 0.27 is complete test
-- You can download and use it.
+-Working on version 0.29 now. Download the source from the release section rather than the master branch version.
+ Master version is working now.
+ 
+- Beta 0.26 and Beta 0.261, Beta 0.262,0.27 is complete test, 0.28 is tested.
+- You can download and use it (Release section).
+
+# Current work list (for Version 0.29)
+  1 Testing CAT Control with Software using hamlib on Linux
+  2 BFO setting based on current value - complete
+  3 Select Tune Step - Testing
+  4 Change Tune control type, Do not keep the original source - Complete
+    - Coded differently after clearing the original source
+    - Prevent malfunction by applying threshold
+  5 stabilize and remove many warning messages - by Pullrequest and merge
+  6 Study on improvement method for cw keying - need idea
+    - set ADC Range value
 
 #NOTICE
 ----------------------------------------------------------------------------
@@ -46,6 +60,10 @@ Prepared or finished tasks for the next version
                   
 ----------------------------------------------------------------------------
 ## REVISION RECORD
+0.28
+ - Fixed CAT problem with hamlib on Linux
+ - restore Protocol autorecovery logic
+
 0.27 
    (First alpha test version, This will be renamed to the major version 1.0)
  - Dual VFO Dial Lock (vfoA Dial lock)

ubitx_20/cat_libs.ino

@@ -1,5 +1,4 @@
 /*************************************************************************
-  KD8CEC's CAT Library for uBITX and HAM
   This source code is written for uBITX, but it can also be used on other radios.
   
   The CAT protocol is used by many radios to provide remote control to comptuers through
@@ -472,7 +471,7 @@ void WriteEEPRom_FT817(byte fromType)
         printLineF2(F("Sidetone set! CAT"));
         EEPROM.put(CW_SIDETONE, sideTone);
         delay(300);                       //If timeout errors occur in the calling software, remove them
-        clearLine2();
+        printLine2("");                   //Ham radio deluxe is the only one that supports this feature yet. and ham radio deluxe has wait time as greater than 500ms
       }
       break;
 
@@ -484,8 +483,7 @@ void WriteEEPRom_FT817(byte fromType)
         printLineF2(F("Sidetone set! CAT"));
         EEPROM.put(CW_SIDETONE, sideTone);
         delay(300);                   //If timeout errors occur in the calling software, remove them
-        clearLine2();
-        line2DisplayStatus = 0;
+        printLine2("");               //Ham radio deluxe is the only one that supports this feature yet. and ham radio deluxe has wait time as greater than 500ms
       }
       break;
 
@@ -505,7 +503,7 @@ void WriteEEPRom_FT817(byte fromType)
       printLineF2(F("CW Speed set!"));
       EEPROM.put(CW_DELAY, cwDelayTime);
       delay(300);
-      clearLine2();
+      printLine2("");
       break;
     case 0x62 : //
       //5-0  CW Speed (4-60 WPM) (#21) From 0 to 38 (HEX) with 0 = 4 WPM and 38 = 60 WPM (1 WPM steps)
@@ -514,7 +512,7 @@ void WriteEEPRom_FT817(byte fromType)
       printLineF2(F("CW Speed set!"));
       EEPROM.put(CW_SPEED, cwSpeed);
       delay(300);
-      clearLine2();
+      printLine2("");
 
       break;
       /*

ubitx_20/cw_autokey.ino

@@ -1,6 +1,4 @@
 /*************************************************************************
-  KD8CEC's Memory Keyer for HAM
-  
   This source code is written for All amateur radio operator, 
   I have not had amateur radio communication for a long time. CW has been 
   around for a long time, and I do not know what kind of keyer and keying 
@@ -15,7 +13,6 @@
   I wrote this code myself, so there is no license restriction. 
   So this code allows anyone to write with confidence.
   But keep it as long as the original author of the code.
-  DE Ian KD8CEC
 -----------------------------------------------------------------------------
    This program is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
@@ -298,12 +295,8 @@ void controlAutoCW(){
           }
           
           printLineFromEEPRom(0, 2, cwStartIndex + displayScrolStep + CW_DATA_OFSTADJ, cwEndIndex + CW_DATA_OFSTADJ); 
-
-          byte diplayAutoCWLine = 0;
-          if ((displayOption1 & 0x01) == 0x01)
-            diplayAutoCWLine = 1;
           
-          lcd.setCursor(0, diplayAutoCWLine);
+          lcd.setCursor(0,0);
           lcd.write(byteToChar(selectedCWTextIndex));
           lcd.write(':');
           isNeedScroll = (cwEndIndex - cwStartIndex) > 14 ? 1 : 0;

ubitx_20/ubitx_20.ino

@@ -1,10 +1,4 @@
 /**
- Since KD8CEC Version 0.29, most of the original code is no longer available.
- Most features(TX, Frequency Range, Ham Band, TX Control, CW delay, start Delay... more) have been added by KD8CEC.
- However, the license rules are subject to the original source rules.
- DE Ian KD8CEC
-
- Original source comment            -------------------------------------------------------------
  * This source file is under General Public License version 3.
  * 
  * This verision uses a built-in Si5351 library
@@ -84,7 +78,6 @@
 #define PTT   (A3)
 #define ANALOG_KEYER (A6)
 #define ANALOG_SPARE (A7)
-#define ANALOG_SMETER (A7)  //by KD8CEC
 
 /** 
  * The Raduino board is the size of a standard 16x2 LCD panel. It has three connectors:
@@ -159,24 +152,7 @@ int count = 0;          //to generally count ticks, loops, etc
 #define TX_TUNE_TYPE 261  //
 #define HAM_BAND_RANGE 262 //FROM (2BYTE) TO (2BYTE) * 10 = 40byte
 #define HAM_BAND_FREQS 302 //40, 1 BAND = 4Byte most bit is mode
-#define TUNING_STEP    342   //TUNING STEP * 6 (index 1 + STEPS 5)
-
-//for reduce cw key error, eeprom address
-#define CW_ADC_MOST_BIT1 348   //most 2bits of  DOT_TO , DOT_FROM, ST_TO, ST_FROM
-#define CW_ADC_ST_FROM   349   //CW ADC Range STRAIGHT KEY from (Lower 8 bit)
-#define CW_ADC_ST_TO     350   //CW ADC Range STRAIGHT KEY to   (Lower 8 bit)
-#define CW_ADC_DOT_FROM  351   //CW ADC Range DOT  from         (Lower 8 bit)
-#define CW_ADC_DOT_TO    352   //CW ADC Range DOT  to           (Lower 8 bit)
-
-#define CW_ADC_MOST_BIT2 353   //most 2bits of BOTH_TO, BOTH_FROM, DASH_TO, DASH_FROM
-#define CW_ADC_DASH_FROM 354   //CW ADC Range DASH from         (Lower 8 bit)
-#define CW_ADC_DASH_TO   355   //CW ADC Range DASH to           (Lower 8 bit)
-#define CW_ADC_BOTH_FROM 356   //CW ADC Range BOTH from         (Lower 8 bit)
-#define CW_ADC_BOTH_TO   357   //CW ADC Range BOTH to           (Lower 8 bit)
-#define CW_KEY_TYPE      358
-
-#define DISPLAY_OPTION1  361   //Display Option1
-#define DISPLAY_OPTION2  362   //Display Option2
+#define TUNING_STEP 342   //TUNING STEP * 6 (index 1 + STEPS 5)
 
 //Check Firmware type and version
 #define FIRMWAR_ID_ADDR 776 //776 : 0x59, 777 :0x58, 778 : 0x68 : Id Number, if not found id, erase eeprom(32~1023) for prevent system error.
@@ -263,23 +239,6 @@ byte isTxType = 0;    //000000[0 - isSplit] [0 - isTXStop]
 byte arTuneStep[5];
 byte tuneStepIndex; //default Value 0, start Offset is 0 because of check new user
 
-byte displayOption1 = 0;
-byte displayOption2 = 0;
-
-//CW ADC Range
-int cwAdcSTFrom = 0;
-int cwAdcSTTo = 0;
-int cwAdcDotFrom = 0;
-int cwAdcDotTo = 0;
-int cwAdcDashFrom = 0;
-int cwAdcDashTo = 0;
-int cwAdcBothFrom = 0;
-int cwAdcBothTo = 0;
-byte cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
-bool Iambic_Key = true;
-#define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
-unsigned char keyerControl = IAMBICB;
-
 //Variables for auto cw mode
 byte isCWAutoMode = 0;          //0 : none, 1 : CW_AutoMode_Menu_Selection, 2 : CW_AutoMode Sending
 byte cwAutoTextCount = 0;       //cwAutoText Count
@@ -308,10 +267,6 @@ unsigned long dbgCount = 0;   //not used now
 unsigned char txFilter = 0;   //which of the four transmit filters are in use
 boolean modeCalibrate = false;//this mode of menus shows extended menus to calibrate the oscillators and choose the proper
                               //beat frequency
-
-unsigned long beforeIdle_ProcessTime = 0; //for check Idle time
-byte line2DisplayStatus = 0;  //0:Clear, 1 : menu, 1: DisplayFrom Idle, 
-                              
 /**
  * Below are the basic functions that control the uBitx. Understanding the functions before 
  * you start hacking around
@@ -379,6 +334,7 @@ void saveBandFreqByIndex(unsigned long f, unsigned long mode, char bandIndex) {
     EEPROM.put(HAM_BAND_FREQS + 4 * bandIndex, (f & 0x3FFFFFFF) | (mode << 30) );
 }
 
+
 /*
   KD8CEC
   When using the basic delay of the Arduino, the program freezes.
@@ -612,13 +568,8 @@ applied Threshold for reduct errors,  dial Lock, dynamic Step
 byte threshold = 2;  //noe action for count
 unsigned long lastEncInputtime = 0;
 int encodedSumValue = 0;
-unsigned long lastTunetime = 0; //if continous moving, skip threshold processing
-byte lastMovedirection = 0; //0 : stop, 1 : cw, 2 : ccw
-
-#define skipThresholdTime 100
 #define encodeTimeOut 1000
-
-void doTuningWithThresHold(){
+void doTuning(){
   int s = 0;
   unsigned long prev_freq;
   long incdecValue = 0;
@@ -635,8 +586,6 @@ void doTuningWithThresHold(){
   if (s == 0) {
     if (encodedSumValue != 0 && (millis() - encodeTimeOut) > lastEncInputtime)
       encodedSumValue = 0;
-
-    lastMovedirection = 0;
     return;
   }
   lastEncInputtime = millis();
@@ -644,25 +593,23 @@ void doTuningWithThresHold(){
   //for check moving direction
   encodedSumValue += (s > 0 ? 1 : -1);
 
-  //check threshold and operator actions (hold dial speed = continous moving, skip threshold check)
-  if ((lastTunetime < millis() - skipThresholdTime) && ((encodedSumValue *  encodedSumValue) <= (threshold * threshold)))
+  //check threshold
+  if ((encodedSumValue *  encodedSumValue) <= (threshold * threshold))
     return;
 
-  lastTunetime = millis();
-
   //Valid Action without noise
   encodedSumValue = 0;
 
   prev_freq = frequency;
   //incdecValue = tuningStep * s;
-  frequency += (arTuneStep[tuneStepIndex -1] * s * (s * s < 10 ? 1 : 3));  //appield weight (s is speed)
+  frequency += (arTuneStep[tuneStepIndex -1] * s);
     
   if (prev_freq < 10000000l && frequency > 10000000l)
     isUSB = true;
     
   if (prev_freq > 10000000l && frequency < 10000000l)
     isUSB = false;
-    
+
   setFrequency(frequency);
   updateDisplay();
 }
@@ -733,10 +680,7 @@ void initSettings(){
   EEPROM.get(VFO_B, vfoB);
   EEPROM.get(CW_SIDETONE, sideTone);
   EEPROM.get(CW_SPEED, cwSpeed);
-  //End of original code
-  
-  //----------------------------------------------------------------
-  //Add Lines by KD8CEC
+
   //for custom source Section =============================
   //ID & Version Check from EEProm 
   //if found different firmware, erase eeprom (32
@@ -771,24 +715,6 @@ void initSettings(){
 
   //CW interval between TX and CW Start
   EEPROM.get(CW_START, delayBeforeCWStartTime);
-  EEPROM.get(CW_KEY_TYPE, cwKeyType);
-  if (cwKeyType > 2)
-    cwKeyType = 0;
-
-  if (cwKeyType == 0)
-    Iambic_Key = false;
-  else
-  {
-    Iambic_Key = true;
-    if (cwKeyType = 1)
-      keyerControl &= ~IAMBICB;
-    else
-      keyerControl |= IAMBICB;
-  }
-    
-
-  EEPROM.get(DISPLAY_OPTION1, displayOption1);
-  EEPROM.get(DISPLAY_OPTION2, displayOption2);
 
   //User callsign information
   if (EEPROM.read(USER_CALLSIGN_KEY) == 0x59)
@@ -823,7 +749,7 @@ void initSettings(){
     hamBandRange[0][0] = 1810; hamBandRange[0][1] = 2000; 
     hamBandRange[1][0] = 3500; hamBandRange[1][1] = 3800; 
     hamBandRange[2][0] = 5351; hamBandRange[2][1] = 5367; 
-    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7300;   //region 1
+    hamBandRange[3][0] = 7000; hamBandRange[3][1] = 7200; 
     hamBandRange[4][0] = 10100; hamBandRange[4][1] = 10150; 
     hamBandRange[5][0] = 14000; hamBandRange[5][1] = 14350; 
     hamBandRange[6][0] = 18068; hamBandRange[6][1] = 18168; 
@@ -855,47 +781,8 @@ void initSettings(){
 
   if (tuneStepIndex == 0) //New User
     tuneStepIndex = 3;
-
-  //CW Key ADC Range ======= adjust set value for reduce cw keying error
-  //by KD8CEC
-  unsigned int tmpMostBits = 0;
-  tmpMostBits = EEPROM.read(CW_ADC_MOST_BIT1);
-  cwAdcSTFrom = EEPROM.read(CW_ADC_ST_FROM)   | ((tmpMostBits & 0x03) << 8);
-  cwAdcSTTo = EEPROM.read(CW_ADC_ST_TO)       | ((tmpMostBits & 0x0C) << 6);
-  cwAdcDotFrom = EEPROM.read(CW_ADC_DOT_FROM) | ((tmpMostBits & 0x30) << 4);
-  cwAdcDotTo = EEPROM.read(CW_ADC_DOT_TO)     | ((tmpMostBits & 0xC0) << 2);
   
-  tmpMostBits = EEPROM.read(CW_ADC_MOST_BIT2);
-  cwAdcDashFrom = EEPROM.read(CW_ADC_DASH_FROM) | ((tmpMostBits & 0x03) << 8);
-  cwAdcDashTo = EEPROM.read(CW_ADC_DASH_TO)     | ((tmpMostBits & 0x0C) << 6);
-  cwAdcBothFrom = EEPROM.read(CW_ADC_BOTH_FROM) | ((tmpMostBits & 0x30) << 4);
-  cwAdcBothTo = EEPROM.read(CW_ADC_BOTH_TO)     | ((tmpMostBits & 0xC0) << 2);
 
-  //default Value (for original hardware)
-  if (cwAdcSTFrom >= cwAdcSTTo)
-  {
-    cwAdcSTFrom = 0;
-    cwAdcSTTo = 50;
-  }
-
-  if (cwAdcBothFrom >= cwAdcBothTo)
-  {
-    cwAdcBothFrom = 51;
-    cwAdcBothTo = 300;
-  }
-  
-  if (cwAdcDotFrom >= cwAdcDotTo)
-  {
-    cwAdcDotFrom = 301;
-    cwAdcDotTo = 600;
-  }
-  if (cwAdcDashFrom >= cwAdcDashTo)
-  {
-    cwAdcDashFrom = 601;
-    cwAdcDashTo = 800;
-  }
-  //end of CW Keying Variables
-  
   if (cwDelayTime < 1 || cwDelayTime > 250)
     cwDelayTime = 60;
 
@@ -905,7 +792,6 @@ void initSettings(){
   if (vfoB_mode < 2)
     vfoB_mode = 3;
 
-  //original code with modified by kd8cec
   if (usbCarrier > 12010000l || usbCarrier < 11990000l)
     usbCarrier = 11995000l;
     
@@ -918,9 +804,8 @@ void initSettings(){
      vfoB = 14150000l;  
      vfoB_mode = 3;
   }
-  //end of original code section
 
-  //for protect eeprom life by KD8CEC
+  //for protect eeprom life
   vfoA_eeprom = vfoA;
   vfoB_eeprom = vfoB;
   vfoA_mode_eeprom = vfoA_mode;
@@ -956,7 +841,6 @@ void initPorts(){
 
   pinMode(PTT, INPUT_PULLUP);
   pinMode(ANALOG_KEYER, INPUT_PULLUP);
-  pinMode(ANALOG_SMETER, INPUT); //by KD8CEC
 
   pinMode(CW_TONE, OUTPUT);  
   digitalWrite(CW_TONE, 0);
@@ -992,7 +876,7 @@ void setup()
   
   //Serial.begin(9600);
   lcd.begin(16, 2);
-  printLineF(1, F("CECBT v0.31")); 
+  printLineF(1, F("CECBT v0.27")); 
 
   Init_Cat(38400, SERIAL_8N1);
   initMeter(); //not used in this build
@@ -1006,7 +890,7 @@ void setup()
   else {
     printLineF(0, F("uBITX v0.20")); 
     delay(500);
-    clearLine2();
+    printLine2(""); 
   }
   
   initPorts();     
@@ -1079,13 +963,8 @@ void loop(){
     if (ritOn)
       doRIT();
     else 
-      doTuningWithThresHold();
-
-    if (isCWAutoMode == 0 && beforeIdle_ProcessTime < millis() - 500) {
-      idle_process();
-      beforeIdle_ProcessTime = millis();
-    }
-  } //end of check TX Status
+      doTuning();
+  }
 
   //we check CAT after the encoder as it might put the radio into TX
   Check_Cat(inTx? 1 : 0);

ubitx_20/ubitx_factory_alignment.ino

@@ -14,7 +14,6 @@ void btnWaitForClick(){
 void factory_alignment(){
         
   factoryCalibration(1);
-  line2DisplayStatus = 1;
 
   if (calibration == 0){
     printLine2("Setup Aborted");

ubitx_20/ubitx_idle.ino

@@ -1,131 +0,0 @@
-/*************************************************************************
-  KD8CEC's uBITX Idle time Processing
-  Functions that run at times that do not affect TX, CW, and CAT
-  It is called in 1/10 time unit.
------------------------------------------------------------------------------
-   This program is free software: you can redistribute it and/or modify
-   it under the terms of the GNU General Public License as published by
-   the Free Software Foundation, either version 3 of the License, or
-   (at your option) any later version.
-
-   This program is distributed in the hope that it will be useful,
-   but WITHOUT ANY WARRANTY; without even the implied warranty of
-   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-   GNU General Public License for more details.
-
-   You should have received a copy of the GNU General Public License
-   along with this program.  If not, see <http://www.gnu.org/licenses/>.
-
-**************************************************************************/
-byte line2Buffer[17];
-//KD8CEC 200Hz ST
-//L14.150 200Hz ST
-//U14.150 +150khz
-
-//Example Line2 Optinal Display
-void updateLine2Buffer()
-{
-  unsigned long tmpFreq = 0;
-
-  if (ritOn)
-  {
-    line2Buffer[0] = 'R';
-    line2Buffer[1] = 'i';
-    line2Buffer[2] = 't';
-    line2Buffer[3] = 'T';
-    line2Buffer[4] = 'X';
-    line2Buffer[5] = ':';
-
-    //display frequency
-    tmpFreq = ritTxFrequency;
-    for (int i = 15; i >= 6; i--) {
-      if (tmpFreq > 0) {
-        if (i == 12 || i == 8) line2Buffer[i] = '.';
-        else {
-          line2Buffer[i] = tmpFreq % 10 + 0x30;
-          tmpFreq /= 10;
-        }
-      }
-      else
-        line2Buffer[i] = ' ';
-    }
-
-    return;
-  }
-  
-  if (vfoActive == VFO_B)
-  {
-    tmpFreq = vfoA;
-    //line2Buffer[0] = 'A';
-  }
-  else 
-  {
-    tmpFreq = vfoB;
-    //line2Buffer[0] = 'B';
-  }
-
-  //U14.150.100
-  //display frequency
-  for (int i = 9; i >= 0; i--) {
-    if (tmpFreq > 0) {
-      if (i == 2 || i == 6) line2Buffer[i] = '.';
-      else {
-        line2Buffer[i] = tmpFreq % 10 + 0x30;
-        tmpFreq /= 10;
-      }
-    }
-    else
-      line2Buffer[i] = ' ';
-  }
-
-  line2Buffer[6] = 'k';
-  
-  line2Buffer[7] = ' ';
-
-  //Step
-  byte tmpStep = arTuneStep[tuneStepIndex -1];
-  for (int i = 10; i >= 8; i--) {
-    if (tmpStep > 0) {
-        line2Buffer[i] = tmpStep % 10 + 0x30;
-        tmpStep /= 10;
-    }
-    else
-      line2Buffer[i] = ' ';
-  }
-  line2Buffer[11] = 'H';
-  line2Buffer[12] = 'z';
-
-  line2Buffer[13] = ' ';
-  //if (
-  //Check CW Key cwKeyType = 0; //0: straight, 1 : iambica, 2: iambicb
-  if (cwKeyType == 0)
-  {
-    line2Buffer[14] = 'S';
-    line2Buffer[15] = 'T';
-  }
-  else if (cwKeyType == 1)
-  {
-    line2Buffer[14] = 'I';
-    line2Buffer[15] = 'A';
-  }
-  else
-  {
-    line2Buffer[14] = 'I';
-    line2Buffer[15] = 'B';
-  }
-}
-
-void idle_process()
-{
-  //space for user graphic display
-  if (menuOn == 0)
-  {
-    //if line2DisplayStatus == 0 <-- this condition is clear Line, you can display any message
-    //if (line2DisplayStatus == 0) {
-      updateLine2Buffer();
-      printLine2(line2Buffer);
-      line2DisplayStatus = 2;
-    //}
-  }
-}
-

ubitx_20/ubitx_keyer.ino

@@ -1,9 +1,8 @@
 /**
- CW Keyer
- CW Key logic change with ron's code (ubitx_keyer.cpp)
- Ron's logic has been modified to work with the original uBITX by KD8CEC
-
- Original Comment ----------------------------------------------------------------------------
+ * CW Keyer
+ * CW Key logic change with ron's code (ubitx_keyer.cpp) <=== **********************************
+ * The file you are working on. The code only applies and is still in testing. <==== ***********
+ * 
  * The CW keyer handles either a straight key or an iambic / paddle key.
  * They all use just one analog input line. This is how it works.
  * The analog line has the internal pull-up resistor enabled. 
@@ -83,167 +82,204 @@ void cwKeyUp(){
   cwTimeout = millis() + cwDelayTime * 10;
 }
 
-//Variables for Ron's new logic
+/*****************************************************************************
+// New logic, by RON
+// modified by KD8CEC
+******************************************************************************/
 #define DIT_L 0x01 // DIT latch
 #define DAH_L 0x02 // DAH latch
 #define DIT_PROC 0x04 // DIT is being processed
 #define PDLSWAP 0x08 // 0 for normal, 1 for swap
 #define IAMBICB 0x10 // 0 for Iambic A, 1 for Iambic B
 enum KSTYPE {IDLE, CHK_DIT, CHK_DAH, KEYED_PREP, KEYED, INTER_ELEMENT };
+
 static long ktimer;
+
+bool Iambic_Key = true;
+unsigned char keyerControl = IAMBICB;
 unsigned char keyerState = IDLE;
 
-//Below is a test to reduce the keying error. do not delete lines
+//Below is a test to reduce the keying error.
+/*
+char update_PaddleLatch(byte isUpdateKeyState) {
+  int paddle = analogRead(ANALOG_KEYER);
+  unsigned char tmpKeyerControl;
+
+  if (paddle > 800)               // above 4v is up
+    tmpKeyerControl = 0;
+  //else if (paddle > 600)         // 4-3v is DASH
+  else if (paddle > 693 && paddle < 700)         // 4-3v is DASH
+    tmpKeyerControl |= DAH_L;
+  //else if (paddle > 300)        //1-2v is DOT
+  else if (paddle > 323 && paddle < 328)        //1-2v is DOT
+    tmpKeyerControl |= DIT_L;
+  //else if (paddle > 50)
+  else if (paddle > 280 && paddle < 290)
+    tmpKeyerControl |= (DAH_L | DIT_L) ;     //both are between 1 and 2v
+  else
+    tmpKeyerControl = 0 ;   //STRAIGHT KEY in original code
+    //keyerControl |= (DAH_L | DIT_L) ;   //STRAIGHT KEY in original code
+  
+  if (isUpdateKeyState == 1) {
+    keyerControl |= tmpKeyerControl;
+  }
+
+  byte buff[17];
+  sprintf(buff, "Key : %d", paddle);
+  if (tmpKeyerControl > 0)
+    printLine2(buff);
+  
+  return tmpKeyerControl;
+
+  //if (analogRead(ANALOG_DOT)   < 600 ) keyerControl |= DIT_L;
+  //if (analogRead(ANALOG_DASH)  < 600 ) keyerControl |= DAH_L;
+}
+*/
+
 //create by KD8CEC for compatible with new CW Logic
 char update_PaddleLatch(byte isUpdateKeyState) {
-  unsigned char tmpKeyerControl;
   int paddle = analogRead(ANALOG_KEYER);
+  unsigned char tmpKeyerControl;
 
-  if (paddle >= cwAdcDashFrom && paddle <= cwAdcDashTo)
+  if (paddle > 800)               // above 4v is up
+    tmpKeyerControl = 0;
+  else if (paddle > 600)         // 4-3v is DASH
     tmpKeyerControl |= DAH_L;
-  else if (paddle >= cwAdcDotFrom && paddle <= cwAdcDotTo)
+  else if (paddle > 300)        //1-2v is DOT
     tmpKeyerControl |= DIT_L;
-  else if (paddle >= cwAdcBothFrom && paddle <= cwAdcBothTo)
-    tmpKeyerControl |= (DAH_L | DIT_L) ;     
-  else 
-  {
-    if (Iambic_Key)
-      tmpKeyerControl = 0 ;
-    else if (paddle >= cwAdcSTFrom && paddle <= cwAdcSTTo)
-      tmpKeyerControl = DIT_L ;
-     else
-       tmpKeyerControl = 0 ; 
-  }
+  else if (paddle > 50)
+    tmpKeyerControl |= (DAH_L | DIT_L) ;     //both are between 1 and 2v
+  else
+    tmpKeyerControl = 0 ;   //STRAIGHT KEY in original code
+    //keyerControl |= (DAH_L | DIT_L) ;   //STRAIGHT KEY in original code
   
-  if (isUpdateKeyState == 1)
+  if (isUpdateKeyState == 1) {
     keyerControl |= tmpKeyerControl;
+  }
 
   return tmpKeyerControl;
+  //if (analogRead(ANALOG_DOT)   < 600 ) keyerControl |= DIT_L;
+  //if (analogRead(ANALOG_DASH)  < 600 ) keyerControl |= DAH_L;
 }
 
-/*****************************************************************************
-// New logic, by RON
-// modified by KD8CEC
-******************************************************************************/
 void cwKeyer(void){
   byte paddle;
   lastPaddle = 0;
   int dot,dash;
   bool continue_loop = true;
   unsigned tmpKeyControl = 0;
-  
-  if( Iambic_Key ) {
-    while(continue_loop) {
-      switch (keyerState) {
-        case IDLE:
-          tmpKeyControl = update_PaddleLatch(0);
-          if ( tmpKeyControl == DAH_L || tmpKeyControl == DIT_L || 
-            tmpKeyControl == (DAH_L | DIT_L) || (keyerControl & 0x03)) {
-             update_PaddleLatch(1);
-             keyerState = CHK_DIT;
-          }else{
-            if (0 < cwTimeout && cwTimeout < millis()){
-              cwTimeout = 0;
-              stopTx();
-            }
-            continue_loop = false;
-          }
-          break;
-    
-        case CHK_DIT:
-          if (keyerControl & DIT_L) {
-            keyerControl |= DIT_PROC;
-            ktimer = cwSpeed;
-            keyerState = KEYED_PREP;
-          }else{
-            keyerState = CHK_DAH;
-          }
-          break;
-    
-        case CHK_DAH:
-          if (keyerControl & DAH_L) {
-            ktimer = cwSpeed*3;
-            keyerState = KEYED_PREP;
-          }else{
-            keyerState = IDLE;
-          }
-          break;
-    
-        case KEYED_PREP:
-          ktimer += millis(); // set ktimer to interval end time
-          keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
-          keyerState = KEYED; // next state
-          if (!inTx){
-            keyDown = 0;
-            cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
-            startTx(TX_CW, 1);
-          }
-          cwKeydown();
-          break;
-    
-        case KEYED:
-          if (millis() > ktimer) { // are we at end of key down ?
-           cwKeyUp();
-           ktimer = millis() + cwSpeed; // inter-element time
-            keyerState = INTER_ELEMENT; // next state
-          }else if (keyerControl & IAMBICB) {
-            update_PaddleLatch(1); // early paddle latch in Iambic B mode
-          }
-          break;
-    
-        case INTER_ELEMENT:
-          // Insert time between dits/dahs
-          update_PaddleLatch(1); // latch paddle state
-          if (millis() > ktimer) { // are we at end of inter-space ?
-            if (keyerControl & DIT_PROC) { // was it a dit or dah ?
-              keyerControl &= ~(DIT_L + DIT_PROC); // clear two bits
-              keyerState = CHK_DAH; // dit done, check for dah
-            }else{
-              keyerControl &= ~(DAH_L); // clear dah latch
-              keyerState = IDLE; // go idle
-            }
-          }
-          break;
-      }
-  
-      Check_Cat(3);
-    } //end of while
-  }
-  else{
-    while(1){
-      if (update_PaddleLatch(0) == DIT_L) {
-        // if we are here, it is only because the key is pressed
-        if (!inTx){
-          keyDown = 0;
-          cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT; 
-          startTx(TX_CW, 1);
-        }
-        cwKeydown();
-        
-        while ( update_PaddleLatch(0) == DIT_L ) 
-          delay_background(1, 3);
-          
-        cwKeyUp();
-      }
-      else{
+if( Iambic_Key ){
+
+while(continue_loop){
+  switch (keyerState) {
+    case IDLE:
+      tmpKeyControl = update_PaddleLatch(0);
+      if ( tmpKeyControl == DAH_L || tmpKeyControl == DIT_L || 
+        tmpKeyControl == (DAH_L | DIT_L) || (keyerControl & 0x03)) {
+        //DIT or DASH or current state DIT & DASH
+        //(analogRead(ANALOG_DOT)  < 600) ||  //DIT
+        //(analogRead(ANALOG_DASH)  < 600) || //DIT
+        //   (keyerControl & 0x03)) {
+         update_PaddleLatch(1);
+         keyerState = CHK_DIT;
+      }else{
         if (0 < cwTimeout && cwTimeout < millis()){
           cwTimeout = 0;
-          keyDown = 0;
           stopTx();
         }
-        if (!cwTimeout)
-          return;
-        // got back to the beginning of the loop, if no further activity happens on straight key
-        // we will time out, and return out of this routine 
-        //delay(5);
-        delay_background(5, 3);
-        continue;
+        continue_loop = false;
       }
+      break;
 
-      Check_Cat(2);
-    } //end of while
-  }   //end of elese
+    case CHK_DIT:
+      if (keyerControl & DIT_L) {
+        keyerControl |= DIT_PROC;
+        ktimer = cwSpeed;
+        keyerState = KEYED_PREP;
+      }else{
+        keyerState = CHK_DAH;
+      }
+      break;
+
+    case CHK_DAH:
+      if (keyerControl & DAH_L) {
+        ktimer = cwSpeed*3;
+        keyerState = KEYED_PREP;
+      }else{
+        keyerState = IDLE;
+      }
+      break;
+
+    case KEYED_PREP:
+      ktimer += millis(); // set ktimer to interval end time
+      keyerControl &= ~(DIT_L + DAH_L); // clear both paddle latch bits
+      keyerState = KEYED; // next state
+      if (!inTx){
+        keyDown = 0;
+        cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT;
+        startTx(TX_CW, 0);
+      }
+      cwKeydown();
+      break;
+
+    case KEYED:
+      if (millis() > ktimer) { // are we at end of key down ?
+       cwKeyUp();
+       ktimer = millis() + cwSpeed; // inter-element time
+        keyerState = INTER_ELEMENT; // next state
+      }else if (keyerControl & IAMBICB) {
+        update_PaddleLatch(1); // early paddle latch in Iambic B mode
+      }
+      break;
+
+    case INTER_ELEMENT:
+      // Insert time between dits/dahs
+      update_PaddleLatch(1); // latch paddle state
+      if (millis() > ktimer) { // are we at end of inter-space ?
+        if (keyerControl & DIT_PROC) { // was it a dit or dah ?
+          keyerControl &= ~(DIT_L + DIT_PROC); // clear two bits
+          keyerState = CHK_DAH; // dit done, check for dah
+        }else{
+          keyerControl &= ~(DAH_L); // clear dah latch
+          keyerState = IDLE; // go idle
+        }
+      }
+      break;
+  }
+} //end of while
+
+}else{
+  while(1){
+    //if (analogRead(ANALOG_DOT) < 600){
+      if (update_PaddleLatch(0) == DIT_L) {
+      // if we are here, it is only because the key is pressed
+      if (!inTx){
+        keyDown = 0;
+        cwTimeout = millis() + cwDelayTime * 10;  //+ CW_TIMEOUT; 
+        startTx(TX_CW, 0);
+      }
+      // start the transmission)
+      cwKeydown();
+      //while ( analogRead(ANALOG_DOT) < 600 ) delay(1);
+      while ( update_PaddleLatch(0) == DIT_L ) delay(1);
+      cwKeyUp();
+    }else{
+      if (0 < cwTimeout && cwTimeout < millis()){
+        cwTimeout = 0;
+        keyDown = 0;
+        stopTx();
+      }
+      if (!cwTimeout)
+        return;
+      // got back to the beginning of the loop, if no further activity happens on straight key
+      // we will time out, and return out of this routine 
+      delay(5);
+      continue;
+   }
+} //end of else
 }
+}
+
 
 
 //=======================================================================================

ubitx_20/ubitx_menu.ino

@@ -13,7 +13,6 @@
 #define printLineF1(x) (printLineF(1, x))
 #define printLineF2(x) (printLineF(0, x))
 
-//Ham band move by KD8CEC
 void menuBand(int btn){
   int knob = 0;
   int stepChangeCount = 0;
@@ -118,7 +117,6 @@ void menuBand(int btn){
   menuOn = 0;
 }
 
-//Convert Mode, Number by KD8CEC
 //0: default, 1:not use, 2:LSB, 3:USB, 4:CW, 5:AM, 6:FM
 byte modeToByte(){
   if (isUSB)
@@ -127,15 +125,12 @@ byte modeToByte(){
     return 2;
 }
 
-//Convert Number to Mode by KD8CEC
 void byteToMode(byte modeValue){
   if (modeValue == 3)
     isUSB = 1;
   else
     isUSB = 0;
 }
-
-//Convert Number to Mode by KD8CEC
 void byteWithFreqToMode(byte modeValue){
   if (modeValue == 3)
     isUSB = 1;
@@ -145,7 +140,6 @@ void byteWithFreqToMode(byte modeValue){
     isUSB = 0;
 }
 
-//VFO Toggle and save VFO Information, modified by KD8CEC
 void menuVfoToggle(int btn, char isUseDelayTime)
 {
   if (!btn){
@@ -235,189 +229,6 @@ void menuSidebandToggle(int btn){
   }
 }
 
-/*
-//Select CW Key Type by KD8CEC
-void menuSetupKeyType(int btn){
-  if (!btn && digitalRead(PTT) == HIGH){
-      if (Iambic_Key)
-        printLineF2(F("Key: Straight?"));
-      else
-        printLineF2(F("Key: Fn=A, PTT=B"));
-  }
-  else {
-      if (Iambic_Key)
-      {
-        printLineF2(F("Straight Key!"));
-        Iambic_Key = false;
-      }
-      else
-      {
-        Iambic_Key = true;
-        if (btn)
-        {
-          keyerControl &= ~IAMBICB;
-          printLineF2(F("IAMBICA Key!"));
-        }
-        else
-        {
-          keyerControl |= IAMBICB;
-          printLineF2(F("IAMBICB Key!"));
-        }
-      }
-      
-    delay_background(500, 0);
-    printLine2ClearAndUpdate();
-    menuOn = 0;
-  }
-}
-*/
-
-//Select CW Key Type by KD8CEC
-void menuSetupKeyType(int btn){
-  int knob = 0;
-  int selectedKeyType = 0;
-  int moveStep = 0;
-  if (!btn && digitalRead(PTT) == HIGH){
-        printLineF2(F("Change Key Type?"));
-  }
-  else {
-    printLineF2(F("Press PTT to set"));
-    delay_background(500, 0);
-    selectedKeyType = cwKeyType;
-    while(!btnDown() && digitalRead(PTT) == HIGH){
-
-      //Display Key Type
-      if (selectedKeyType == 0)
-        printLineF1(F("Straight"));
-      else if (selectedKeyType == 1)
-        printLineF1(F("IAMBICA"));
-      else if (selectedKeyType == 2)
-        printLineF1(F("IAMBICB"));
-
-      knob = enc_read();
-
-      if (knob != 0)
-      {
-        moveStep += (knob > 0 ? 1 : -1);
-        if (selectedKeyType > 0 && moveStep < -3) {
-          selectedKeyType--;
-          moveStep = 0;
-        }
-        else if (selectedKeyType < 2 && moveStep > 3) {
-          selectedKeyType++;
-          moveStep = 0;
-        }
-      }
-
-      Check_Cat(0);  //To prevent disconnections
-    }
-    
-    //save the setting
-    if (digitalRead(PTT) == LOW){
-      printLineF2(F("CW Key Type set!"));
-      cwKeyType = selectedKeyType;
-      EEPROM.put(CW_KEY_TYPE, cwKeyType);
-
-      if (cwKeyType == 0)
-        Iambic_Key = false;
-      else
-      {
-        Iambic_Key = true;
-        if (cwKeyType = 1)
-          keyerControl &= ~IAMBICB;
-        else
-          keyerControl |= IAMBICB;
-      }
-      delay_background(2000, 0);
-    }
-    
-    printLine2ClearAndUpdate();
-    menuOn = 0;
-  }
-}
-
-//Analog pin monitoring with CW Key and function keys connected.
-//by KD8CEC
-void menuADCMonitor(int btn){
-  int adcPinA0 = 0;  //A0(BLACK, EncoderA)
-  int adcPinA1 = 0;  //A1(BROWN, EncoderB)
-  int adcPinA2 = 0;  //A2(RED, Function Key)
-  int adcPinA3 = 0;  //A3(ORANGE, CW Key)
-  int adcPinA6 = 0;  //A6(BLUE, Ptt)
-  int adcPinA7 = 0;  //A7(VIOLET, Spare)
-  unsigned long pressKeyTime = 0;
-  
-  if (!btn){
-        printLineF2(F("ADC Line Monitor"));
-        return;
-  }
-  
-  printLineF2(F("Exit:Long PTT"));
-  delay_background(2000, 0);
-  printLineF1(F("A0   A1   A2"));
-  printLineF2(F("A3   A6   A7"));
-  delay_background(3000, 0);
-  
-  while (true) {
-    adcPinA0 = analogRead(A0);  //A0(BLACK, EncoderA)
-    adcPinA1 = analogRead(A1);  //A1(BROWN, EncoderB)
-    adcPinA2 = analogRead(A2);  //A2(RED, Function Key)
-    adcPinA3 = analogRead(A3);  //A3(ORANGE, CW Key)
-    adcPinA6 = analogRead(A6);  //A6(BLUE, Ptt)
-    adcPinA7 = analogRead(A7);  //A7(VIOLET, Spare)
-
-/*
-  sprintf(c, "%4d %4d %4d", adcPinA0, adcPinA1, adcPinA2);
-  printLine1(c);
-  sprintf(c, "%4d %4d %4d", adcPinA3, adcPinA6, adcPinA7);
-  printLine2(c);
-*/  
-  
-    if (adcPinA6 < 10) {
-      if (pressKeyTime == 0)
-        pressKeyTime = millis();
-      else if (pressKeyTime < (millis() - 3000))
-          break;
-    }
-    else
-      pressKeyTime = 0;
-    
-    ltoa(adcPinA0, c, 10);
-    //strcat(b, c);
-    strcpy(b, c);
-    strcat(b, ", ");
-    
-    ltoa(adcPinA1, c, 10);
-    strcat(b, c);
-    strcat(b, ", ");
-    
-    ltoa(adcPinA2, c, 10);
-    strcat(b, c);
-
-    printLine1(b);
-
-    //strcpy(b, " ");
-    ltoa(adcPinA3, c, 10);
-    strcpy(b, c);
-    strcat(b, ", ");
-
-    ltoa(adcPinA6, c, 10);
-    strcat(b, c);
-    strcat(b, ", ");
-    
-    ltoa(adcPinA7, c, 10);
-    strcat(b, c);
-    printLine2(b);
-    
-    delay_background(200, 0);
-  } //end of while
-      
-  printLine2ClearAndUpdate();
-  menuOn = 0;
-}
-
-//Function to disbled transmission
-//by KD8CEC
 void menuTxOnOff(int btn, byte optionType){
   if (!btn){
     if ((isTxType & optionType) == 0)
@@ -531,7 +342,6 @@ void menuCWSpeed(int btn){
     menuOn = 0;
 }
 
-//Builtin CW Keyer Logic by KD8CEC
 void menuCWAutoKey(int btn){
     if (!btn){
      printLineF2(F("CW AutoKey Mode?"));
@@ -555,7 +365,6 @@ void menuCWAutoKey(int btn){
     menuOn = 0;
 }
 
-//Modified by KD8CEC
 void menuSetupCwDelay(int btn){
     int knob = 0;
     int tmpCWDelay = cwDelayTime * 10;
@@ -604,7 +413,6 @@ void menuSetupCwDelay(int btn){
     menuOn = 0;
 }
 
-//CW Time delay by KD8CEC
 void menuSetupTXCWInterval(int btn){
     int knob = 0;
     int tmpTXCWInterval = delayBeforeCWStartTime * 2;
@@ -800,6 +608,7 @@ void menuSetupCalibration(int btn){
   menuOn = 0;
 }
 
+
 void printCarrierFreq(unsigned long freq){
 
   memset(c, 0, sizeof(c));
@@ -815,7 +624,6 @@ void printCarrierFreq(unsigned long freq){
   printLine2(c);    
 }
 
-//modified by KD8CEC (just 1 line remarked //usbCarrier = ...
 void menuSetupCarrier(int btn){
   int knob = 0;
   unsigned long prevCarrier;
@@ -869,7 +677,6 @@ void menuSetupCarrier(int btn){
   menuOn = 0; 
 }
 
-//Modified by KD8CEC
 void menuSetupCwTone(int btn){
     int knob = 0;
     int prev_sideTone;
@@ -918,7 +725,6 @@ void menuSetupCwTone(int btn){
     menuOn = 0; 
  }
 
-//Lock Dial move by KD8CEC
 void setDialLock(byte tmpLock, byte fromMode) {
   if (tmpLock == 1)
     isDialLock |= (vfoActive == VFO_A ? 0x01 : 0x02);
@@ -941,7 +747,6 @@ unsigned int btnDownTimeCount;
 #define PRESS_ADJUST_TUNE 1000
 #define PRESS_LOCK_CONTROL 2000
 
-//Modified by KD8CEC
 void doMenu(){
   int select=0, i,btnState;
   char isNeedDisplay = 0;
@@ -1025,7 +830,7 @@ void doMenu(){
     btnState = btnDown();
 
     if (i > 0){
-      if (modeCalibrate && select + i < 170)
+      if (modeCalibrate && select + i < 150)
         select += i;
       if (!modeCalibrate && select + i < 80)
         select += i;
@@ -1063,12 +868,8 @@ void doMenu(){
     else if (select < 130 && modeCalibrate)
       menuSetupTXCWInterval(btnState);
     else if (select < 140 && modeCalibrate)
-      menuSetupKeyType(btnState);
-    else if (select < 150 && modeCalibrate)
-      menuADCMonitor(btnState);
-    else if (select < 160 && modeCalibrate)
       menuTxOnOff(btnState, 0x01);      //TX OFF / ON
-    else if (select < 170 && modeCalibrate)
+    else if (select < 150 && modeCalibrate)
       menuExit(btnState);
 
     Check_Cat(0);  //To prevent disconnections

ubitx_20/ubitx_ui.ino

@@ -116,9 +116,6 @@ void drawMeter(int8_t needle){
 
 // The generic routine to display one line on the LCD 
 void printLine(unsigned char linenmbr, const char *c) {
-  if ((displayOption1 & 0x01) == 0x01)
-    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
-    
   if (strcmp(c, printBuff[linenmbr])) {     // only refresh the display when there was a change
     lcd.setCursor(0, linenmbr);             // place the cursor at the beginning of the selected line
     lcd.print(c);
@@ -148,9 +145,6 @@ void printLineF(char linenmbr, const __FlashStringHelper *c)
 
 #define LCD_MAX_COLUMN 16
 void printLineFromEEPRom(char linenmbr, char lcdColumn, byte eepromStartIndex, byte eepromEndIndex) {
-  if ((displayOption1 & 0x01) == 0x01)
-    linenmbr = (linenmbr == 0 ? 1 : 0); //Line Toggle
-  
   lcd.setCursor(lcdColumn, linenmbr);
 
   for (byte i = eepromStartIndex; i <= eepromEndIndex; i++)
@@ -174,12 +168,6 @@ void printLine2(const char *c){
   printLine(0,c);
 }
 
-void clearLine2()
-{
-  printLine2("");
-  line2DisplayStatus = 0;
-}
-
 //  short cut to print to the first line
 void printLine1Clear(){
   printLine(1,"");
@@ -191,7 +179,6 @@ void printLine2Clear(){
 
 void printLine2ClearAndUpdate(){
   printLine(0, "");
-  line2DisplayStatus = 0;  
   updateDisplay();
 }
 
@@ -264,22 +251,18 @@ void updateDisplay() {
   //  strcat(c, " TX");
   printLine(1, c);
 
-  byte diplayVFOLine = 1;
-  if ((displayOption1 & 0x01) == 0x01)
-    diplayVFOLine = 0;
-
   if ((vfoActive == VFO_A && ((isDialLock & 0x01) == 0x01)) ||
     (vfoActive == VFO_B && ((isDialLock & 0x02) == 0x02))) {
-    lcd.setCursor(5,diplayVFOLine);
+    lcd.setCursor(5,1);
     lcd.write((uint8_t)0);
   }
   else if (isCWAutoMode == 2){
-    lcd.setCursor(5,diplayVFOLine);
+    lcd.setCursor(5,1);
     lcd.write(0x7E);
   }
   else
   {
-    lcd.setCursor(5,diplayVFOLine);
+    lcd.setCursor(5,1);
     lcd.write(":");
   }