mirror of
https://codeberg.org/mclemens/ubitxv6.git
synced 2024-11-15 14:46:03 -05:00
46 lines
2.5 KiB
C
46 lines
2.5 KiB
C
#pragma once
|
|
|
|
/*
|
|
* Pin configurations for uBiTXv6
|
|
*
|
|
* Attached devices are:
|
|
* * A rotory encoder for tuning, which has a built-in push button for selection
|
|
* * A Push-to-talk button input
|
|
* * A morse keyer input, using analog voltage divider for paddle support
|
|
* * A SI5351A 3-output frequency generator
|
|
* * A model tjctm24028-spi touch screen LCD, which has:
|
|
* * An ILI9341 display controller
|
|
* * A XPT2046 touch controller
|
|
* * A TX/RX output control pin
|
|
* * A tone output pin to provide audio feedback to the operator when sending CW
|
|
* * Three filter selection output control pins
|
|
* * A CW keydown output
|
|
* * Optionally, a serial CAT interface
|
|
*/
|
|
|
|
static const uint8_t PIN_ENC_A = A0; // Tuning encoder interface
|
|
static const uint8_t PIN_ENC_B = A1; // Tuning encoder interface
|
|
static const uint8_t PIN_ENC_PUSH_BUTTON = A2; // Tuning encoder interface
|
|
static const uint8_t PIN_PTT = A3; // Sense it for ssb and as a straight key for cw operation
|
|
//A4 is I2C SDA
|
|
//A5 is I2C SCK
|
|
static const uint8_t PIN_ANALOG_KEYER = A6; // This is used as keyer. The analog port has 4.7K pull up resistor. Details are in the circuit description on www.hfsignals.com
|
|
static const uint8_t PIN_ANALOG_SPARE = A7; // Not used yet
|
|
|
|
//13 is SPI CLK
|
|
//12 is SPI MISO
|
|
//11 is SPI MOSI
|
|
static const uint8_t PIN_TFT_CS = 10; // Selects the LCD controller on SPI interface (active low)
|
|
static const uint8_t PIN_TFT_DC = 9; // Tells the LCD controller if it's getting data (D, high) or commands (C, low)
|
|
static const uint8_t PIN_TOUCH_CS = 8; // Selects the touch controller on SPI interface (active low)
|
|
static const uint8_t PIN_TX_RXn = 7; // Pin from the Nano to the radio to switch to TX (HIGH) and RX(LOW)
|
|
static const uint8_t PIN_CW_TONE = 6; // Generates a square wave sidetone while sending the CW
|
|
static const uint8_t PIN_TX_LPF_A = 5; // The 30 MHz LPF is permanently connected in the output of the PA...
|
|
static const uint8_t PIN_TX_LPF_B = 4; // ...Alternatively, either 3.5 MHz, 7 MHz or 14 Mhz LPFs are...
|
|
static const uint8_t PIN_TX_LPF_C = 3; // ...switched inline depending upon the TX frequency
|
|
static const uint8_t PIN_CW_KEY = 2; // Pin goes high during CW keydown to transmit the carrier.
|
|
// ... The PIN_CW_KEY is needed in addition to the TX/RX key as the...
|
|
// ...key can be up within a tx period
|
|
//1 is UART RX
|
|
//0 is UART TX
|