#pragma once #include "settings.h" /* The ubitx is powered by an arduino nano. The pin assignment is as folows * */ #define ENC_A (A0) // Tuning encoder interface #define ENC_B (A1) // Tuning encoder interface #define FBUTTON (A2) // Tuning encoder interface #define PTT (A3) // Sense it for ssb and as a straight key for cw operation #define ANALOG_KEYER (A6) // This is used as keyer. The analog port has 4.7K pull up resistor. Details are in the circuit description on www.hfsignals.com #define ANALOG_SPARE (A7) // Not used yet #define TX_RX (7) // Pin from the Nano to the radio to switch to TX (HIGH) and RX(LOW) #define CW_TONE (6) // Generates a square wave sidetone while sending the CW. #define TX_LPF_A (5) // The 30 MHz LPF is permanently connected in the output of the PA... #define TX_LPF_B (4) // ...Alternatively, either 3.5 MHz, 7 MHz or 14 Mhz LPFs are... #define TX_LPF_C (3) // ...switched inline depending upon the TX frequency #define CW_KEY (2) // Pin goes high during CW keydown to transmit the carrier. // ... The CW_KEY is needed in addition to the TX/RX key as the... // ...key can be up within a tx period /** pin assignments 14 T_IRQ 2 std changed 13 T_DOUT (parallel to SOD/MOSI, pin 9 of display) 12 T_DIN (parallel to SDI/MISO, pin 6 of display) 11 T_CS 9 (we need to specify this) 10 T_CLK (parallel to SCK, pin 7 of display) 9 SDO(MSIO) 12 12 (spi) 8 LED A0 8 (not needed, permanently on +3.3v) (resistor from 5v, 7 SCK 13 13 (spi) 6 SDI 11 11 (spi) 5 D/C A3 7 (changable) 4 RESET A4 9 (not needed, permanently +5v) 3 CS A5 10 (changable) 2 GND GND 1 VCC VCC The model is called tjctm24028-spi it uses an ILI9341 display controller and an XPT2046 touch controller. */ #define TFT_DC 9 #define TFT_CS 10 #define CS_PIN 8 //this is the pin to select the touch controller on spi interface /** * The Arduino, unlike C/C++ on a regular computer with gigabytes of RAM, has very little memory. * We have to be very careful with variables that are declared inside the functions as they are * created in a memory region called the stack. The stack has just a few bytes of space on the Arduino * if you declare large strings inside functions, they can easily exceed the capacity of the stack * and mess up your programs. * We circumvent this by declaring a few global buffers as kitchen counters where we can * slice and dice our strings. These strings are mostly used to control the display or handle * the input and output from the USB port. We must keep a count of the bytes used while reading * the serial port as we can easily run out of buffer space. This is done in the serial_in_count variable. */ extern char c[30], b[128]; /** * The second set of 16 pins on the Raduino's bottom connector are have the three clock outputs and the digital lines to control the rig. * This assignment is as follows : * Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 * GND +5V CLK0 GND GND CLK1 GND GND CLK2 GND D2 D3 D4 D5 D6 D7 * These too are flexible with what you may do with them, for the Raduino, we use them to : * - TX_RX line : Switches between Transmit and Receive after sensing the PTT or the morse keyer * - CW_KEY line : turns on the carrier for CW */ /** * The uBITX is an upconnversion transceiver. The first IF is at 45 MHz. * The first IF frequency is not exactly at 45 Mhz but about 5 khz lower, * this shift is due to the loading on the 45 Mhz crystal filter by the matching * L-network used on it's either sides. * The first oscillator works between 48 Mhz and 75 MHz. The signal is subtracted * from the first oscillator to arriive at 45 Mhz IF. Thus, it is inverted : LSB becomes USB * and USB becomes LSB. * The second IF of 11.059 Mhz has a ladder crystal filter. If a second oscillator is used at * 56 Mhz (appox), the signal is subtracted FROM the oscillator, inverting a second time, and arrives * at the 11.059 Mhz ladder filter thus doouble inversion, keeps the sidebands as they originally were. * If the second oscillator is at 33 Mhz, the oscilaltor is subtracated from the signal, * thus keeping the signal's sidebands inverted. The USB will become LSB. * We use this technique to switch sidebands. This is to avoid placing the lsbCarrier close to * 11 MHz where its fifth harmonic beats with the arduino's 16 Mhz oscillator's fourth harmonic */ #define INIT_USB_FREQ (11059200l) // limits the tuning and working range of the ubitx between 3 MHz and 30 MHz #define LOWEST_FREQ (100000l) #define HIGHEST_FREQ (30000000l) static const uint32_t THRESHOLD_USB_LSB = 10000000L; /* these are functions implemented in the main file named as ubitx_xxx.ino */ void active_delay(int delay_by); void saveVFOs(); void setFrequency(const unsigned long freq, const bool transmit = false); void startTx(TuningMode_e tx_mode); void stopTx(); void ritEnable(unsigned long f); void ritDisable(); void checkCAT(); void cwKeyer(void); void switchVFO(Vfo_e vfoSelect); int enc_read(void); // returns the number of ticks in a short interval, +ve in clockwise, -ve in anti-clockwise void enc_setup(void); // Setups up initial values and interrupts. int btnDown(); //returns true if the encoder button is pressed /* these functions are called universally to update the display */ void updateDisplay(); //updates just the VFO frequency to show what is in 'frequency' variable void redrawVFOs(); //redraws only the changed digits of the vfo void guiUpdate(); //repaints the entire screen. Slow!! void drawCommandbar(char *text); void drawTx(); //getValueByKnob() provides a reusable dialog box to get a value from the encoder, the prefix and postfix //are useful to concatanate the values with text like "Set Freq to " x " KHz" int getValueByKnob(int minimum, int maximum, int step_size, int initial, char* prefix, char *postfix); //main functions to check if any button is pressed and other user interface events void doCommands(); //does the commands with encoder to jump from button to button /* these are functiosn implemented in ubitx_si5351.cpp */ void si5351bx_setfreq(uint8_t clknum, uint32_t fout); void initOscillators(); void si5351_set_calibration(int32_t cal); //calibration is a small value that is nudged to make up for the inaccuracies of the reference 25 MHz crystal frequency