mirror of
https://codeberg.org/mclemens/ubitxv6.git
synced 2024-11-19 06:46:00 -05:00
Swap EEPROM virtualization hardcoding for multi-byte reading using enums
This commit is contained in:
Reed Nightingale
parent
53a39b0699
commit
eba70c64ef
203
ubitx_cat.cpp
203
ubitx_cat.cpp
@ -95,6 +95,27 @@ struct ReadTxStatus_t {
|
||||
uint8_t PttOff : 1;
|
||||
};
|
||||
|
||||
//Values based on http://www.ka7oei.com/ft817_memmap.html
|
||||
enum Ft817Eeprom_e : uint16_t {
|
||||
VfoAndBankSelect = 0x0055,
|
||||
TuningModes = 0x0057,
|
||||
KeyerStatus = 0x0058,
|
||||
BandSelect = 0x0059,
|
||||
BeepVolume = 0x005C,
|
||||
CwPitch = 0x005E,
|
||||
CwWeight = 0x005F,
|
||||
CwDelay = 0x0060,
|
||||
SidetoneVolume = 0x0061,
|
||||
CwSpeed = 0x0062,
|
||||
VoxGain = 0x0063,
|
||||
CatBaudRate = 0x0064,
|
||||
SsbMicVolume = 0x0067,
|
||||
AmMicVolume = 0x0068,
|
||||
FmMicVolume = 0x0069,
|
||||
TxPower = 0x0079,
|
||||
AntennaSelectAndSplit = 0x007A,
|
||||
};
|
||||
|
||||
//for broken protocol
|
||||
static const uint16_t CAT_RECEIVE_TIMEOUT_MS = 500;
|
||||
|
||||
@ -171,34 +192,11 @@ uint32_t readFreq(uint8_t* cmd) {
|
||||
return ret*10;
|
||||
}
|
||||
|
||||
//void ReadEEPRom_FT817(uint8_t fromType)
|
||||
void catReadEEPRom(uint8_t* cat)
|
||||
void catGetEeprom(const uint16_t read_address, uint8_t* response)
|
||||
{
|
||||
//for remove warnings
|
||||
uint8_t temp0 = cat[P1];
|
||||
uint8_t temp1 = cat[P2];
|
||||
|
||||
cat[P1] = 0;
|
||||
cat[P2] = 0;
|
||||
//for remove warnings[1] = 0;
|
||||
|
||||
switch (temp1)
|
||||
switch (read_address)
|
||||
{
|
||||
case 0x45 : //
|
||||
if (temp0 == 0x03)
|
||||
{
|
||||
cat[P1] = 0x00;
|
||||
cat[P2] = 0xD0;
|
||||
}
|
||||
break;
|
||||
case 0x47 : //
|
||||
if (temp0 == 0x03)
|
||||
{
|
||||
cat[P1] = 0xDC;
|
||||
cat[P2] = 0xE0;
|
||||
}
|
||||
break;
|
||||
case 0x55 :
|
||||
case Ft817Eeprom_e::VfoAndBankSelect:
|
||||
//0 : VFO A/B 0 = VFO-A, 1 = VFO-B
|
||||
//1 : MTQMB Select 0 = (Not MTQMB), 1 = MTQMB ("Memory Tune Quick Memory Bank")
|
||||
//2 : QMB Select 0 = (Not QMB), 1 = QMB ("Quick Memory Bank")
|
||||
@ -207,10 +205,10 @@ void catReadEEPRom(uint8_t* cat)
|
||||
//5 : Memory/MTUNE select 0 = Memory, 1 = MTUNE
|
||||
//6 :
|
||||
//7 : MEM/VFO Select 0 = Memory, 1 = VFO (A or B - see bit 0)
|
||||
cat[P1] = 0x80 + ((VFO_B == globalSettings.activeVfo) ? 1 : 0);
|
||||
cat[P2] = 0x00;
|
||||
*response = 0x80 //always report VFO mode
|
||||
| ((VFO_B == globalSettings.activeVfo) ? 0x01 : 0x00);
|
||||
break;
|
||||
case 0x57 : //
|
||||
case Ft817Eeprom_e::TuningModes:
|
||||
//0 : 1-0 AGC Mode 00 = Auto, 01 = Fast, 10 = Slow, 11 = Off
|
||||
//2 DSP On/Off 0 = Off, 1 = On (Display format)
|
||||
//4 PBT On/Off 0 = Off, 1 = On (Passband Tuning)
|
||||
@ -218,98 +216,126 @@ void catReadEEPRom(uint8_t* cat)
|
||||
//6 Lock On/Off 0 = Off, 1 = On (Dial Lock)
|
||||
//7 FST (Fast Tuning) On/Off 0 = Off, 1 = On (Fast tuning)
|
||||
|
||||
cat[P1] = 0xC0;
|
||||
cat[P2] = 0x40;
|
||||
*response = 0xC0;
|
||||
break;
|
||||
case 0x59 : // band select VFO A Band Select 0000 = 160 M, 0001 = 75 M, 0010 = 40 M, 0011 = 30 M, 0100 = 20 M, 0101 = 17 M, 0110 = 15 M, 0111 = 12 M, 1000 = 10 M, 1001 = 6 M, 1010 = FM BCB, 1011 = Air, 1100 = 2 M, 1101 = UHF, 1110 = (Phantom)
|
||||
case Ft817Eeprom_e::KeyerStatus:
|
||||
//1-0: power meter mode: 00 = Power, 01 = ALC, 10 = SWR, 11 = MOD
|
||||
//2 : CW paddle reverse: 1 = reverse
|
||||
//3 :
|
||||
//4 : CW keyer on/off: 1 = on
|
||||
//5 : break on/off: 1 = semi break-in
|
||||
//6 : voltmeter display on/off: 1 = display voltmeter
|
||||
//7 : VOX on/off: 1 = on
|
||||
*response = 0x40;
|
||||
break;
|
||||
case Ft817Eeprom_e::BandSelect:
|
||||
//band select VFO A Band Select 0000 = 160 M, 0001 = 75 M, 0010 = 40 M, 0011 = 30 M, 0100 = 20 M, 0101 = 17 M, 0110 = 15 M, 0111 = 12 M, 1000 = 10 M, 1001 = 6 M, 1010 = FM BCB, 1011 = Air, 1100 = 2 M, 1101 = UHF, 1110 = (Phantom)
|
||||
//http://www.ka7oei.com/ft817_memmap.html
|
||||
//CAT_BUFF[0] = 0xC2;
|
||||
//CAT_BUFF[1] = 0x82;
|
||||
break;
|
||||
case 0x5C : //Beep Volume (0-100) (#13)
|
||||
cat[P1] = 0xB2;
|
||||
cat[P2] = 0x42;
|
||||
case Ft817Eeprom_e::BeepVolume:
|
||||
//6-0 : Beep Volume (0-100) (#13)
|
||||
//7 : Beep Freq: 0 = 440Hz, 1 = 880Hz
|
||||
*response = 0xB2;
|
||||
break;
|
||||
case 0x5E :
|
||||
case Ft817Eeprom_e::CwPitch:
|
||||
//3-0 : CW Pitch (300-1000 Hz) (#20) From 0 to E (HEX) with 0 = 300 Hz and each step representing 50 Hz
|
||||
//5-4 : Lock Mode (#32) 00 = Dial, 01 = Freq, 10 = Panel
|
||||
//7-6 : Op Filter (#38) 00 = Off, 01 = SSB, 10 = CW
|
||||
//CAT_BUFF[0] = 0x08;
|
||||
cat[P1] = (globalSettings.cwSideToneFreq - 300)/50;
|
||||
cat[P2] = 0x25;
|
||||
*response = (globalSettings.cwSideToneFreq - 300)/50;
|
||||
break;
|
||||
case 0x61 : //globalSettings.cwSideToneFreq (Volume) (#44)
|
||||
cat[P1] = globalSettings.cwSideToneFreq % 50;
|
||||
cat[P2] = 0x08;
|
||||
case Ft817Eeprom_e::CwWeight:
|
||||
//4-0 : CW Weight (1.:2.5-1:4.5) (#22) From 0 to 14 (HEX) with 0 = 1:2.5, incrementing in 0.1 weight steps
|
||||
//5 : 420 ARS (#2), 1 = on
|
||||
//6 : 144 ARS (#1), 1 = on
|
||||
//7 : Sql/RF-G (#45), 1 = on
|
||||
*response = 0x25;
|
||||
break;
|
||||
case 0x5F : //
|
||||
//4-0 CW Weight (1.:2.5-1:4.5) (#22) From 0 to 14 (HEX) with 0 = 1:2.5, incrementing in 0.1 weight steps
|
||||
//5 420 ARS (#2) 0 = Off, 1 = On
|
||||
//6 144 ARS (#1) 0 = Off, 1 = On
|
||||
//7 Sql/RF-G (#45) 0 = Off, 1 = On
|
||||
cat[P1] = 0x32;
|
||||
cat[P2] = 0x08;
|
||||
case Ft817Eeprom_e::SidetoneVolume:
|
||||
//Sidetone (Volume) (#44)
|
||||
*response = globalSettings.cwSideToneFreq % 50;
|
||||
break;
|
||||
case 0x60 : //CW Delay (10-2500 ms) (#17) From 1 to 250 (decimal) with each step representing 10 ms
|
||||
cat[P1] = globalSettings.cwActiveTimeoutMs / 10;
|
||||
cat[P2] = 0x32;
|
||||
case Ft817Eeprom_e::CwDelay:
|
||||
//CW Delay (10-2500 ms) (#17) From 1 to 250 (decimal) with each step representing 10 ms
|
||||
*response = globalSettings.cwActiveTimeoutMs / 10;
|
||||
break;
|
||||
case 0x62 : //
|
||||
case Ft817Eeprom_e::CwSpeed:
|
||||
//5-0 CW Speed (4-60 WPM) (#21) From 0 to 38 (HEX) with 0 = 4 WPM and 38 = 60 WPM (1 WPM steps)
|
||||
//7-6 Batt-Chg (6/8/10 Hours (#11) 00 = 6 Hours, 01 = 8 Hours, 10 = 10 Hours
|
||||
//CAT_BUFF[0] = 0x08;
|
||||
cat[P1] = 1200 / globalSettings.cwDitDurationMs - 4;
|
||||
cat[P2] = 0xB2;
|
||||
*response = (1200 / globalSettings.cwDitDurationMs) - 4;
|
||||
break;
|
||||
case 0x63 : //
|
||||
case Ft817Eeprom_e::VoxGain:
|
||||
//6-0 VOX Gain (#51) Contains 1-100 (decimal) as displayed
|
||||
//7 Disable AM/FM Dial (#4) 0 = Enable, 1 = Disable
|
||||
cat[P1] = 0xB2;
|
||||
cat[P2] = 0xA5;
|
||||
*response = 0xB2;
|
||||
break;
|
||||
case 0x64 : //
|
||||
case Ft817Eeprom_e::CatBaudRate:
|
||||
//4-0 : VOX Delay (#50) 0 = 100 Ms with each step representing 100 Ms. 24 = 2500 Ms
|
||||
//5 : Emergency (#28) 0 = Off, 1 = On
|
||||
//7-6 : CAT Rate (4800, 9600, 38400) (#14) 00 = 4800, 01 = 9600, 10 = 38400 Baud
|
||||
*response = 0xA5;
|
||||
break;
|
||||
case 0x67 : //6-0 SSB Mic (#46) Contains 0-100 (decimal) as displayed
|
||||
cat[P1] = 0xB2;
|
||||
cat[P2] = 0xB2;
|
||||
case Ft817Eeprom_e::SsbMicVolume:
|
||||
//6-0 : SSB Mic (#46) Contains 0-100 (decimal) as displayed
|
||||
*response = 0xB2;
|
||||
break;
|
||||
case 0x69 : //FM Mic (#29) Contains 0-100 (decimal) as displayed
|
||||
case 0x78 :
|
||||
if (VfoMode_e::VFO_MODE_USB == GetActiveVfoMode())
|
||||
cat[P1] = OperatingMode_e::USB << 5;
|
||||
else
|
||||
cat[P1] = OperatingMode_e::LSB << 5;
|
||||
case Ft817Eeprom_e::AmMicVolume:
|
||||
//6-0 : AM Mic (#5) Contains 0-100 (decimal) as displayed
|
||||
//7 : Mic Key (#36) 1 = on
|
||||
*response = 0xB2;
|
||||
break;
|
||||
case 0x79 : //
|
||||
case Ft817Eeprom_e::FmMicVolume:
|
||||
//6-0 : FM Mic (#29) Contains 0-100 (decimal) as displayed
|
||||
//7 : Mic Scan (#37) 1 = on
|
||||
case 0x78 ://??
|
||||
if (VfoMode_e::VFO_MODE_USB == GetActiveVfoMode()){
|
||||
*response = OperatingMode_e::USB << 5;
|
||||
}
|
||||
else{
|
||||
*response = OperatingMode_e::LSB << 5;
|
||||
}
|
||||
break;
|
||||
case Ft817Eeprom_e::TxPower:
|
||||
//1-0 TX Power (All bands) 00 = High, 01 = L3, 10 = L2, 11 = L1
|
||||
//3 PRI On/Off 0 = Off, 1 = On
|
||||
//DW On/Off 0 = Off, 1 = On
|
||||
//SCN (Scan) Mode 00 = No scan, 10 = Scan up, 11 = Scan down
|
||||
//ART On/Off 0 = Off, 1 = On
|
||||
cat[P1] = 0x00;
|
||||
cat[P2] = 0x00;
|
||||
*response = 0x00;
|
||||
break;
|
||||
case 0x7A : //SPLIT
|
||||
//7A 0 HF Antenna Select 0 = Front, 1 = Rear
|
||||
//7A 1 6 M Antenna Select 0 = Front, 1 = Rear
|
||||
//7A 2 FM BCB Antenna Select 0 = Front, 1 = Rear
|
||||
//7A 3 Air Antenna Select 0 = Front, 1 = Rear
|
||||
//7A 4 2 M Antenna Select 0 = Front, 1 = Rear
|
||||
//7A 5 UHF Antenna Select 0 = Front, 1 = Rear
|
||||
//7A 6 ? ?
|
||||
//7A 7 SPL On/Off 0 = Off, 1 = On
|
||||
case Ft817Eeprom_e::AntennaSelectAndSplit:
|
||||
//0 : HF Antenna Select 0 = Front, 1 = Rear
|
||||
//1 : 6 M Antenna Select 0 = Front, 1 = Rear
|
||||
//2 : FM BCB Antenna Select 0 = Front, 1 = Rear
|
||||
//3 : Air Antenna Select 0 = Front, 1 = Rear
|
||||
//4 : 2 M Antenna Select 0 = Front, 1 = Rear
|
||||
//5 : UHF Antenna Select 0 = Front, 1 = Rear
|
||||
//6 : ? ?
|
||||
//7 : SPL On/Off 0 = Off, 1 = On
|
||||
|
||||
cat[P1] = (globalSettings.splitOn ? 0xFF : 0x7F);
|
||||
*response = (globalSettings.splitOn ? 0xFF : 0x7F);
|
||||
break;
|
||||
case 0xB3 : //
|
||||
cat[P1] = 0x00;
|
||||
cat[P2] = 0x4D;
|
||||
case 0xB3 : //0xB1 is the base address of Base address of VFO A, 40 M.
|
||||
*response = 0x00;
|
||||
break;
|
||||
|
||||
case 0xB4 : //0xB1 is the base address of Base address of VFO A, 40 M.
|
||||
//2-0 : FM Step (Menu # 30) 000 = 5 kHz, 001 = 6.25 kHz, 010 = 10 kHz, 011 = 12.5 kHz, 100 = 15 kHz, 101 = 20 kHz, 110 = 25 kHz, 111 = 50 kHz
|
||||
//5-3 : AM Step (Menu #6) 000 = 2.5 kHz, 001 = 5 kHz, 010 = 9 kHz, 011 = 10 kHz, 100 = 12.5 kHz, 101 = 25 kHz
|
||||
//7-6 : SSB Step (Menu # 47) 00 = 1 kHz, 01 = 2.5 kHz, 10 = 5 kHz
|
||||
*response = 0x4D;
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
// sent the data
|
||||
Serial.write(cat, 2);
|
||||
//Maps some of the fixed memory layout of the FT817's EEPROM
|
||||
void catReadEEPRom(uint8_t* cmd, uint8_t* response)
|
||||
{
|
||||
const uint16_t read_address = cmd[P1] << 8 | cmd[P2];
|
||||
|
||||
catGetEeprom(read_address,response);
|
||||
catGetEeprom(read_address+1,response+1);
|
||||
}
|
||||
|
||||
void processCatCommand(uint8_t* cmd) {
|
||||
@ -397,7 +423,8 @@ void processCatCommand(uint8_t* cmd) {
|
||||
break;
|
||||
|
||||
case 0xBB: //Read FT-817 EEPROM Data (for comfirtable)
|
||||
catReadEEPRom(cmd);
|
||||
catReadEEPRom(cmd,response);
|
||||
response_length = 2;
|
||||
break;
|
||||
|
||||
case Ft817Command_e::ReadRxStatus:
|
||||
|
||||
Loading…
Reference in New Issue
Block a user