If VEX.V is an immediate, it should not be subject to register range
checks.
If the WW flag is set, REX_W needs to be OR'd in, not XOR'd, because
the map might have the W bit set for matching purposes.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
- Significantly overhauled the disassembler internals to make
better use of the information already in the instruction template
and to reduce the implementation differences with the assembler
- Add APX support to the disassembler
- Fix problem with disassembler truncating addresses of jumps
- Fix generation of invalid EAs in 16-bit mode
- Fix array overrun for types in a few modules
- Fix invalid ND flag on near JMP
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
- rex2.w is used as a opcode extension (JMPABS), not rex2.x1 as an
earlier version of the spec had.
- Segment prefixes used as Jcc hints are valid in 64-bit mode.
- Avoid duplicate warning messages for ignored/invalid prefixes.
* emit_prefixes() is called twice during code generation.
- Add the UDB #UD opcode in 64-bit mode; SALC is 16/32-bit only.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Add a optimization frameword for operand narrowing (where the operand
size doesn't matter beyond a certain range because only certain bits
are referenced.)
Add a macro *and* matching facility for dealing with segment selectors, which are
typically rm16/r32/r64, but exactly how that is applied varies
depending on if a datum is read or written.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Add the MOVBE CPUID flag, add helper patterns for 16-bit BSWAP
emulation. Unfortunately using ROL/ROR for registers other than the
ones for which XCHG can work clobbers the flags.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
More work on cleaning up instruction patterns, fixing matchig corner
cases, and tidying up the organization of insns.dat.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
More matching and macrofication work.
Improve some error and warning messages.
Update some travis tests for better messages and added optimizations.
Fix duplicated warning messages for the same out-of-range value
problem.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Tag pseudo-instructions explicitly and don't set any CPU level flag
for those.
Change insnsa.c to have (length, pointer) rather than using an ever
increasing in size sentinel at the end of each table. This also means
that empty tables (Dx, INCBIN) can be omitted entirely.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add more instruction macros and fix problems. Adjust some matching
problems.
Remove all FUTURE tags from the instruction list, and add a bunch of
new CPUID tags. Hopefully a small step toward actually getting CPU
feature selection working properly in the future.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
"nw" now means: 64-bit operand size is the default, o32 is not
permitted in 64-bit mode.
"osz" means: instruction size determined by prefixes, otherwise the
mode default.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add more improvements to the macro features. Now it is possible to
generate the -X versions of the shift instructions as part of the
macroization, which is highly desirable in order to allow them to be
generated using {nf} syntax.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Work more on the macro facility. Add the ability to kill an
instruction pattern based on expansion (if the token KILL appears.)
Add APX patterns to the arithmetic macro and macroize the shift and
rotate patterns.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make the macro facility in preinsns.pl more general, and relying less
on evaluating Perl constructs. This *might* be practical with some
more work, to move to a data file, but wait until we have a better
idea of the needs.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This is a WIP checkpoint; not all tests pass yet.
More matching changes, and hopefully something much closer to what
really is desired now. The number of required patterns is now much
smaller.
However, a lot of *changes* are needed to the patterns.
Since some patterns are repeated all over the place, clean up the
x86/addflags.pl script and make it able to generate macro-based
common patterns; first use being the patterns for the "basic 8"
arithmetic patterns.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Work through a number of changes toward making matching a lot saner,
both to reduce the number of patterns to generate for APX but also to
make a number of code patterns simpler.
This replaces a fair number of byte codes.
Improve a number of error messages, especially related to overflows.
Move process_insn() from nasm.c to assemble.c, as it really is the
primary entry point to the assembler module.
Reorder some prefixes. In particular, F2/F3 override 66 when used as a
mandatory prefix, so it makes more sense for them to be closer to the
opcode.
Move a lot more information into struct insn. It is better to have it
in one place; memory consumption is not an issue because struct insn
is transient information.
Get rid of "optimization levels" and replace it with a mask of
flags. That was already halfway done; complete the job.
Replace seg:offset in struct out_data with a struct location. It would
be better to extend this to more places, too.
The ARx and SMx flags are now explicit bitmasks, instead of having a
couple of hard-coded ranges.
Add __func__ to assert or panic messages.
Because of prefix and message changes, a number of travis tests had to
be audited and updated.
Fix a number of instruction patterns which had .128 when they ought to
be .lig. This is no longer a minor issue with the disassembler: for
AVX10, the pattern vector length determines how SAE/RC are encoded,
and there is no valid 128-bit encoding. However, with .lig the 512-bit
encoding can be used.
Separate "o64nw" into two pieces: opsize 64 and "nw" = "REX.w not necessary". The
latter can be included in non-64-bit patterns. "o64" still set REX.W
since that is still the common thing.
New "osz" bytecode: emit an OSP *or* REX.W depending on the current
mode and operand size. Useful for special cases like "nop" where "o64
nop" probably wants to be encoded as "48 90".
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add MOVSX[D] -> CBW/CWDE/CDQE optimization patterns when the suitable
form of the AX register are referenced.
Add MOVZX reg64,rm32 pattern which converts to a 32-bit MOV.
Add MOVZXD reg64,rm32 alias pattern for consistency.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For the instructions ending in -x because they don't modify the flags,
also accept {nf}. Add 2-operand relaxed versions like for most other
instructions, too.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For the instruction space that are explicitly excluded by REX2, add
NOAPX tags. This was done with an automated script.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Implement the JMPABS instruction, which can also be specified as JMP
ABS for consistency. Since ABS is already a keyword, this does not
pollute the namespace.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
EVEX encoding is really messy, with the 4th register bit in one of
several places depending on which type of register it is. It seems to
work now.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
a
Support generating code for APX instruction and add support for the
{nf} prefix.
No disassembler support yet, and only a handful instructions encoded.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Change the byte code format and the byte code compiler to be able to
generate various kinds of APX-format instructions.
THE NEW BYTE CODES ARE NOT YET IMPLEMENTED IN THE ASSEMBLER OR
DISASSEMBLER.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Comment was missing a semicolon; fix to avoid unnecessary warning and
to make sure the documentation is generated correctly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add support for VEX-encoded SHA512-NI instructions.
Signed-off-by: Tomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Kind of embarrassing... I had not implemented the FRED instruction,
despite personally being one of the architects of FRED ;)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
"LOCK XCHG reg,mem" would issue a warning for being unlockable, which
is incorrect. In this case the RM encoding is simply an alias for the
MR encoding. Add a "LOCK1" bit to deal with that.
However, XCHG is *always* locked, so create a new warning to
explicitly flag a user-specified LOCK XCHG; default off.
Consider optimizing that prefix away in the future, but for now, let's
stick to the user-requested code sequence.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For VEX instructions created *after* the corresponding EVEX
instructions, we need the user to either explicitly declare them {vex}
or specifying "cpu latevex".
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add vector instructions from the Intel Instruction Set Extensions
document, version 046, September 2022.
Still need to check for missing instructions that have already passed
through the ISE into the SDM.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Additional nonvector instructions from the Intel Instruction Set
Extensions document 319433-046 September 2022.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
